Engine Control DTCS
ENGINE CONTROLS DTCS (MED17.7 ENGINE 157)
| MB DTC | Generic DTC | Description |
| B002000 | - | This error code can be ignored and erased. |
| B10E800 | - | This error code can be ignored and erased. |
| B10E900 | - | This error code can be ignored and erased. |
| B10EC00 | - | This error code can be ignored and erased. |
| B10EC01 | - | This error code can be ignored and erased. |
| B110900 | - | This error code can be ignored and erased. |
| B110A00 | - | This error code can be ignored and erased. |
| B1CE812 | - | The digital output for the crash signal has a malfunction. There is a short circuit to positive. |
| B218E00 | - | Actuation of the radiator shutters has a malfunction. |
| B218E04 | - | This error code can be ignored and erased. |
| B218E11 | - | Actuation of the radiator shutters has a malfunction. There is a short circuit to ground. |
| B218E12 | - | Actuation of the radiator shutters has a malfunction. There is a short circuit to positive. |
| B218E13 | - | Actuation of the radiator shutters has a malfunction. There is an open circuit. |
| B218E48 | - | Actuation of the radiator shutters has a malfunction. There is an error in the control memory. |
| C000100 | - | This error code can be ignored and erased. |
| C000200 | - | This error code can be ignored and erased. |
| C000300 | - | This error code can be ignored and erased. |
| C000400 | - | This error code can be ignored and erased. |
| C001000 | - | This error code can be ignored and erased. |
| C001100 | - | This error code can be ignored and erased. |
| C001200 | - | This error code can be ignored and erased. |
| C001400 | - | This error code can be ignored and erased. |
| C001500 | - | This error code can be ignored and erased. |
| C001600 | - | This error code can be ignored and erased. |
| C001800 | - | This error code can be ignored and erased. |
| C001900 | - | This error code can be ignored and erased. |
| C001A00 | - | This error code can be ignored and erased. |
| C001C00 | - | This error code can be ignored and erased. |
| C001D00 | - | This error code can be ignored and erased. |
| C001E00 | - | This error code can be ignored and erased. |
| C002000 | - | This error code can be ignored and erased. |
| C002100 | - | This error code can be ignored and erased. |
| C002200 | - | This error code can be ignored and erased. |
| C003000 | - | This error code can be ignored and erased. |
| C003100 | - | This error code can be ignored and erased. |
| C003108 | - | The left front wheel speed sensor has a malfunction. There is a signal fault or the message is faulty. |
| C003200 | - | This error code can be ignored and erased. |
| C003300 | - | This error code can be ignored and erased. |
| C003400 | - | This error code can be ignored and erased. |
| C003408 | - | The right front wheel speed sensor has a malfunction. There is a signal fault or the message is faulty. |
| C003500 | - | This error code can be ignored and erased. |
| C003600 | - | This error code can be ignored and erased. |
| C003700 | - | This error code can be ignored and erased. |
| C003708 | - | The left rear wheel speed sensor has a malfunction. There is a signal fault or the message is faulty. |
| C003800 | - | This error code can be ignored and erased. |
| C003900 | - | This error code can be ignored and erased. |
| C003A00 | - | This error code can be ignored and erased. |
| C003A08 | - | The right rear wheel speed sensor has a malfunction. There is a signal fault or the message is faulty. |
| C003B00 | - | This error code can be ignored and erased. |
| C004200 | - | This error code can be ignored and erased. |
| C004600 | - | This error code can be ignored and erased. |
| C004800 | - | This error code can be ignored and erased. |
| C006A00 | - | This error code can be ignored and erased. |
| C109000 | - | This error code can be ignored and erased. |
| C120200 | - | This error code can be ignored and erased. |
| C120300 | - | This error code can be ignored and erased. |
| C123300 | - | This error code can be ignored and erased. |
| C123600 | - | This error code can be ignored and erased. |
| C125000 | - | This error code can be ignored and erased. |
| C125200 | - | This error code can be ignored and erased. |
| C125400 | - | This error code can be ignored and erased. |
| C126000 | - | This error code can be ignored and erased. |
| C127000 | - | This error code can be ignored and erased. |
| C128100 | - | This error code can be ignored and erased. |
| C128200 | - | This error code can be ignored and erased. |
| C182500 | - | This error code can be ignored and erased. |
| C186500 | - | This error code can be ignored and erased. |
| C190800 | - | This error code can be ignored and erased. |
| C191000 | - | This error code can be ignored and erased. |
| C193300 | - | This error code can be ignored and erased. |
| C193400 | - | This error code can be ignored and erased. |
| C196500 | - | This error code can be ignored and erased. |
| C196700 | - | This error code can be ignored and erased. |
| C197500 | - | This error code can be ignored and erased. |
| C197600 | - | This error code can be ignored and erased. |
| C200100 | - | This error code can be ignored and erased. |
| C200200 | - | This error code can be ignored and erased. |
| C212000 | - | Circuit 30 has an open circuit. |
| C212B00 | - | This error code can be ignored and erased. |
| P000000 | - | This error code can be ignored and erased. |
| P000100 | - | Quantity control valve has an electrical fault or open circuit. |
| P000300 | - | Quantity control valve has a short circuit to positive. |
| P000400 | - | The quantity control valve has a short circuit to positive. |
| P000801 | - | The position of the crankshaft (cylinder bank 1) is implausible. There is a general electrical fault. |
| P000903 | - | The position of the crankshaft (cylinder bank 2) is implausible. There is a frequency or pulse width modulation fault. |
| P000E00 | - | The adaptation values of the quantity control valve are outside the valid range. |
| P001000 | - | Actuator 'Intake camshaft' (cylinder bank 1) has an electrical fault or open circuit. |
| P001164 | - | The position of the intake camshaft (cylinder bank 1) deviates from the specified value. There is an implausible signal. |
| P001177 | - | The position of the intake camshaft (cylinder bank 1) deviates from the specified value. The commanded position cannot be reached. |
| P001200 | - | Adjustment of the intake camshaft (cylinder bank 1) is performed late. |
| P001300 | - | Actuator 'Exhaust camshaft' (cylinder bank 1) has an electrical fault or open circuit. |
| P001464 | - | The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. There is an implausible signal. |
| P001477 | - | The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. The commanded position cannot be reached. |
| P001500 | - | Adjustment of the exhaust camshaft (cylinder bank 1) is performed late. |
| P001664 | - | The position of the intake camshaft (cylinder bank 1) is implausible relative to the position of the crankshaft. There is an implausible signal. |
| P001685 | - | The position of the intake camshaft (cylinder bank 1) is implausible relative to the position of the crankshaft. There is a signal above the permissible limit value. |
| P001764 | - | The position of the exhaust camshaft (cylinder bank 1) is implausible relative to the position of the crankshaft. There is an implausible signal. |
| P001785 | - | The position of the exhaust camshaft (cylinder bank 1) is implausible relative to the position of the crankshaft. There is a signal above the permissible limit value. |
| P001864 | - | The position of the intake camshaft (cylinder bank 2) is implausible relative to the position of the crankshaft. There is an implausible signal. |
| P001885 | - | The position of the intake camshaft (cylinder bank 2) is implausible relative to the position of the crankshaft. There is a signal above the permissible limit value. |
| P001964 | - | The position of the exhaust camshaft (cylinder bank 2) is implausible relative to the position of the crankshaft. There is an implausible signal. |
| P001985 | - | The position of the exhaust camshaft (cylinder bank 2) is implausible relative to the position of the crankshaft. There is a signal above the permissible limit value. |
| P002000 | - | Actuator 'Intake camshaft' (cylinder bank 2) has an electrical fault or open circuit. |
| P002164 | - | The position of the intake camshaft (cylinder bank 2) deviates from the specified value. There is an implausible signal. |
| P002177 | - | The position of the intake camshaft (cylinder bank 2) deviates from the specified value. The commanded position cannot be reached. |
| P002200 | - | Adjustment of the intake camshaft (cylinder bank 2) is performed late. |
| P002300 | - | Actuator 'Exhaust camshaft' (cylinder bank 2) has an electrical fault or open circuit. |
| P002464 | - | The position of the exhaust camshaft (cylinder bank 2) deviates from the specified value. There is an implausible signal. |
| P002477 | - | The position of the exhaust camshaft (cylinder bank 2) deviates from the specified value. The commanded position cannot be reached. |
| P002500 | - | Adjustment of the exhaust camshaft (cylinder bank 2) is performed late. |
| P003000 | - | The output for the heater of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. |
| P003100 | - | The output for the heater of oxygen sensor 1 (cylinder bank 1) has a short circuit to ground. |
| P003200 | - | The output for the heater of oxygen sensor 1 (cylinder bank 1) has a short circuit to positive. |
| P003300 | - | The output for the switchover valve for bypass flap 'Charge air' has an electrical fault. |
| P003400 | - | The output for the switchover valve for bypass flap 'Charge air' has a short circuit to ground. |
| P003500 | - | The output for the switchover valve for bypass flap 'Charge air' has a short circuit to positive. |
| P003600 | - | The output for the heater of oxygen sensor 2 (cylinder bank 1) has an electrical fault or open circuit. |
| P003700 | - | The output for the heater of oxygen sensor 2 (cylinder bank 1) has a short circuit to ground. |
| P003800 | - | The output for the heater of oxygen sensor 2 (cylinder bank 1) has a short circuit to positive. |
| P003973 | - | This error code can be ignored and erased. |
| P004000 | - | Oxygen sensors 1 (cylinder banks 1 and 2) have been swapped. |
| P004100 | - | Oxygen sensors 2 (cylinder banks 1 and 2) have been swapped. |
| P005000 | - | The output for the heater of oxygen sensor 1 (cylinder bank 2) has an electrical fault or open circuit. |
| P005100 | - | The output for the heater of oxygen sensor 1 (cylinder bank 2) has a short circuit to ground. |
| P005200 | - | The output for the heater of oxygen sensor 1 (cylinder bank 2) has a short circuit to positive. |
| P005400 | - | The heater for oxygen sensor 2 (cylinder bank 1) has an implausible electrical resistance value. |
| P005600 | - | The output for the heater of oxygen sensor 2 (cylinder bank 2) has an electrical fault or open circuit. |
| P005700 | - | The output for the heater of oxygen sensor 2 (cylinder bank 2) has a short circuit to ground. |
| P005800 | - | The output for the heater of oxygen sensor 2 (cylinder bank 2) has a short circuit to positive. |
| P006000 | - | The heater for oxygen sensor 2 (cylinder bank 2) has an implausible electrical resistance value. |
| P006800 | - | The position of the throttle valve is implausible relative to the mass air flow or intake manifold pressure. |
| P007001 | - | The outside temperature sensor has an electrical fault. There is a general electrical fault. |
| P007062 | - | The outside temperature sensor has an electrical fault. The signal comparison is faulty. |
| P007064 | - | The outside temperature sensor has an electrical fault. There is an implausible signal. |
| P007101 | - | The outside temperature sensor has a malfunction. There is a general electrical fault. |
| P007126 | - | The outside temperature sensor has a malfunction. The signal change rate is below the permissible limit value. |
| P007127 | - | The outside temperature sensor has a malfunction. The signal change rate is above the permissible limit value. |
| P007200 | - | The outside temperature sensor has a short circuit to ground. |
| P007201 | - | The outside temperature sensor has a short circuit to ground. There is a general electrical fault. |
| P007300 | - | The outside temperature sensor has a short circuit to positive. |
| P007301 | - | The outside temperature sensor has a short circuit to positive. There is a general electrical fault. |
| P007B00 | - | The charge air temperature sensor (cylinder bank 1) has a malfunction. |
| P007B27 | - | The charge air temperature sensor (cylinder bank 1) has a malfunction. The signal change rate is above the permissible limit value. |
| P007B28 | - | The charge air temperature sensor (cylinder bank 1) has a malfunction. The signal offset is outside the permissible range. |
| P007B64 | - | This error code can be ignored and erased. |
| P007B84 | - | This error code can be ignored and erased. |
| P007C11 | - | The charge air temperature sensor (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground. |
| P007D12 | - | The charge air temperature sensor (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive. |
| P007E2A | - | The charge air temperature sensor (cylinder bank 1) has a sporadic malfunction. There is no signal change. |
| P008700 | - | The fuel pressure in the system is too low. |
| P008792 | - | The fuel pressure in the system is too low. The function or the instruction is faulty. |
| P008796 | - | The fuel pressure in the system is too low. There is an internal component fault. |
| P008800 | - | The fuel pressure in the system is too high. |
| P008900 | - | Pressure regulating valve 1 has a malfunction. |
| P008992 | - | Pressure regulating valve 1 has a malfunction. The function or the instruction is faulty. |
| P008994 | - | Pressure regulating valve 1 has a malfunction. There is an unexpected instruction. |
| P008A00 | - | The pressure in the fuel low pressure circuit is too low. |
| P008B00 | - | The pressure in the fuel low pressure circuit is too high. |
| P009627 | - | Intake air temperature sensor 2 (cylinder bank 1) has a malfunction. The signal change rate is above the permissible limit value. |
| P009628 | - | Intake air temperature sensor 2 (cylinder bank 1) has a malfunction. The signal offset is outside the permissible range. |
| P009664 | - | Intake air temperature sensor 2 (cylinder bank 1) has a malfunction. There is an implausible signal. |
| P009684 | - | Intake air temperature sensor 2 (cylinder bank 1) has a malfunction. There is a signal below the permissible limit value. |
| P009711 | - | Intake air temperature sensor 2 (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground. |
| P009812 | - | Intake air temperature sensor 2 (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive. |
| P00992A | - | Intake air temperature sensor 2 (cylinder bank 1) has a sporadic malfunction. There is no signal change. |
| P009E07 | - | The pressure relief valve for fuel is jammed open. There is a mechanical fault. |
| P00BC00 | - | The flow rate of mass air flow sensor 1 is too low. |
| P00BD00 | - | The flow rate of mass air flow sensor 1 is too high. |
| P00C000 | - | The output for the switchover valve of bypass flap 'Charge air' 2 has an electrical fault. |
| P00C100 | - | The output for the switchover valve of bypass flap 'Charge air' 2 has a short circuit to ground. |
| P00C200 | - | The output for the switchover valve of bypass flap 'Charge air' 2 has a short circuit to positive. |
| P010126 | - | Mass air flow sensor 1 has a malfunction. The signal change rate is below the permissible limit value. |
| P010127 | - | Mass air flow sensor 1 has a malfunction. The signal change rate is above the permissible limit value. |
| P010129 | - | Mass air flow sensor 1 has a malfunction. There is an invalid signal. |
| P010184 | - | Mass air flow sensor 1 has a malfunction. There is a signal below the permissible limit value. |
| P010185 | - | Mass air flow sensor 1 has a malfunction. There is a signal above the permissible limit value. |
| P010186 | - | Mass air flow sensor 1 has a malfunction. There is an incorrect signal. |
| P010192 | - | Mass air flow sensor 1 has a malfunction. The function or the instruction is faulty. |
| P010211 | - | Mass air flow sensor 1 has a short circuit to ground. There is a short circuit to ground. |
| P010226 | - | Mass air flow sensor 1 has a short circuit to ground. The signal change rate is below the permissible limit value. |
| P010300 | - | Mass air flow sensor 1 has a short circuit to positive. |
| P010327 | - | Mass air flow sensor 1 has a short circuit to positive. The signal change rate is above the permissible limit value. |
| P010616 | - | The intake manifold pressure sensor has a malfunction. The limit value for electrical voltage has not been attained. |
| P010617 | - | The intake manifold pressure sensor has a malfunction. The limit value for electrical voltage has been exceeded. |
| P010628 | - | The intake manifold pressure sensor has a malfunction. The signal offset is outside the permissible range. |
| P010664 | - | The intake manifold pressure sensor has a malfunction. There is an implausible signal. |
| P010668 | - | This error code can be ignored and erased. |
| P010692 | - | The intake manifold pressure sensor has a malfunction. The function or the instruction is faulty. |
| P010693 | - | The intake manifold pressure sensor has a malfunction. There are no instructions. |
| P010694 | - | The intake manifold pressure sensor has a malfunction. There is an unexpected instruction. |
| P010711 | - | The intake manifold pressure sensor has a short circuit to ground. There is a short circuit to ground. |
| P010812 | - | The intake manifold pressure sensor has a short circuit to positive. There is a short circuit to positive. |
| P010B29 | - | Mass air flow sensor 2 has a malfunction. There is an invalid signal. |
| P010B92 | - | Mass air flow sensor 2 has a malfunction. The function or the instruction is faulty. |
| P010C26 | - | Mass air flow sensor 2 has a short circuit to ground. The signal change rate is below the permissible limit value. |
| P010D27 | - | Mass air flow sensor 2 has a short circuit to positive. The signal change rate is above the permissible limit value. |
| P011100 | - | Intake air temperature sensor 1 (cylinder bank 1) has a malfunction. |
| P011127 | - | Intake air temperature sensor 1 (cylinder bank 1) has a malfunction. The signal change rate is above the permissible limit value. |
| P011128 | - | Intake air temperature sensor 1 (cylinder bank 1) has a malfunction. The signal offset is outside the permissible range. |
| P011164 | - | This error code can be ignored and erased. |
| P011184 | - | This error code can be ignored and erased. |
| P011211 | - | Intake air temperature sensor 1 (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground. |
| P011312 | - | Intake air temperature sensor 1 (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive. |
| P01142A | - | Intake air temperature sensor 1 (cylinder bank 1) has a sporadic malfunction. There is no signal change. |
| P011500 | - | Coolant temperature sensor 1 has an electrical fault. |
| P011600 | - | Coolant temperature sensor 1 has a malfunction. |
| P011684 | - | Coolant temperature sensor 1 has a malfunction. There is a signal below the permissible limit value. |
| P011685 | - | Coolant temperature sensor 1 has a malfunction. There is a signal above the permissible limit value. |
| P011686 | - | Coolant temperature sensor 1 has a malfunction. There is an incorrect signal. |
| P011700 | - | Coolant temperature sensor 1 has a short circuit to ground. |
| P011800 | - | Coolant temperature sensor 1 has a short circuit to positive. |
| P011900 | - | Coolant temperature sensor 1 has a sporadic malfunction. |
| P012200 | - | Position sensor 1 for the throttle valve has a short circuit to ground. |
| P012300 | - | Position sensor 1 for the throttle valve has a short circuit to positive. |
| P012800 | - | The coolant temperature is below the coolant thermostat specified temperature. |
| P013011 | - | Oxygen sensor 1 (cylinder bank 1) has an electrical fault. There is a short circuit to ground. |
| P013012 | - | Oxygen sensor 1 (cylinder bank 1) has an electrical fault. There is a short circuit to positive. |
| P013084 | - | Oxygen sensor 1 (cylinder bank 1) has an electrical fault. There is a signal below the permissible limit value. |
| P013300 | - | Oxygen sensor 1 (cylinder bank 1) has a delayed reaction. |
| P013500 | - | The heater for oxygen sensor 1 (cylinder bank 1) has an electrical fault. |
| P013504 | - | The heater for oxygen sensor 1 (cylinder bank 1) has an electrical fault. There is an internal fault. |
| P013584 | - | The heater for oxygen sensor 1 (cylinder bank 1) has an electrical fault. There is a signal below the permissible limit value. |
| P013600 | - | Oxygen sensor 2 (cylinder bank 1) has an electrical fault. |
| P013700 | - | Oxygen sensor 2 (cylinder bank 1) has a short circuit to ground. |
| P013800 | - | Oxygen sensor 2 (cylinder bank 1) has a short circuit to positive. |
| P013A00 | - | The rich/lean switchover of oxygen sensor 2 (cylinder bank 1) is too slow. |
| P013B00 | - | The lean/rich switchover of oxygen sensor 2 (cylinder bank 1) is too slow. |
| P013C00 | - | The rich/lean switchover of oxygen sensor 2 (cylinder bank 2) is too slow. |
| P013D00 | - | The lean/rich switchover of oxygen sensor 2 (cylinder bank 2) is too slow. |
| P013E00 | - | The rich/lean switchover of oxygen sensor 2 (cylinder bank 1) is delayed. |
| P013F00 | - | The lean/rich switchover of oxygen sensor 2 (cylinder bank 1) is delayed. |
| P014200 | - | The NOx sensor (cylinder bank 1) has an electrical fault. |
| P014300 | - | The NOx sensor (cylinder bank 1) has a short circuit to ground. |
| P014526 | - | The NOx sensor 1 (cylinder bank 1) reacts with a delay. The signal change rate is below the permissible limit value. |
| P014527 | - | The NOx sensor 1 (cylinder bank 1) reacts with a delay. The signal change rate is above the permissible limit value. |
| P014A00 | - | The rich/lean switchover of oxygen sensor 2 (cylinder bank 2) is delayed. |
| P014B00 | - | The lean/rich switchover of oxygen sensor 2 (cylinder bank 2) is delayed. |
| P015011 | - | Oxygen sensor 1 (cylinder bank 2) has an electrical fault. There is a short circuit to ground. |
| P015012 | - | Oxygen sensor 1 (cylinder bank 2) has an electrical fault. There is a short circuit to positive. |
| P015084 | - | Oxygen sensor 1 (cylinder bank 2) has an electrical fault. There is a signal below the permissible limit value. |
| P015300 | - | Oxygen sensor 1 (cylinder bank 2) has a delayed reaction. |
| P015500 | - | The heater for oxygen sensor 1 (cylinder bank 1) has an electrical fault. |
| P015504 | - | The heater for oxygen sensor 1 (cylinder bank 2) has an electrical fault. There is an internal fault. |
| P015584 | - | The heater for oxygen sensor 1 (cylinder bank 2) has an electrical fault. There is a signal below the permissible limit value. |
| P015600 | - | Oxygen sensor 2 (cylinder bank 2) has an electrical fault. |
| P015700 | - | Oxygen sensor 2 (cylinder bank 2) has a short circuit to ground. |
| P015800 | - | Oxygen sensor 2 (cylinder bank 2) has a short circuit to positive. |
| P016200 | - | The NOx sensor (cylinder bank 2) has an electrical fault. |
| P016300 | - | The NOx sensor (cylinder bank 2) has a short circuit to ground. |
| P016526 | - | The NOx sensor 1 (cylinder bank 2) reacts with a delay. The signal change rate is below the permissible limit value. |
| P016527 | - | The NOx sensor 1 (cylinder bank 2) reacts with a delay. The signal change rate is above the permissible limit value. |
| P017004 | - | The mixture formation (cylinder bank 1) has a malfunction. There is an internal fault. |
| P017026 | - | This error code can be ignored and erased. |
| P017100 | - | The mixture (cylinder bank 1) is too lean. |
| P017184 | - | The mixture (cylinder bank 1) is too lean. There is a signal below the permissible limit value. |
| P017200 | - | The mixture (cylinder bank 1) is too rich. |
| P017285 | - | The mixture (cylinder bank 1) is too rich. There is a signal above the permissible limit value. |
| P017304 | - | The mixture formation (cylinder bank 2) has a malfunction. There is an internal fault. |
| P017326 | - | This error code can be ignored and erased. |
| P017400 | - | The mixture (cylinder bank 2) is too lean. |
| P017484 | - | The mixture (cylinder bank 2) is too lean. There is a signal below the permissible limit value. |
| P017500 | - | The mixture (cylinder bank 2) is too rich. |
| P017585 | - | The mixture (cylinder bank 2) is too rich. There is a signal above the permissible limit value. |
| P018000 | - | The fuel temperature sensor has an electrical fault. |
| P018108 | - | This error code can be ignored and erased. |
| P018116 | - | The fuel temperature sensor has a malfunction. The limit value for electrical voltage has not been attained. |
| P018117 | - | The fuel temperature sensor has a malfunction. The limit value for electrical voltage has been exceeded. |
| P018127 | - | The fuel temperature sensor has a malfunction. The signal change rate is above the permissible limit value. |
| P018128 | - | The fuel temperature sensor has a malfunction. The signal offset is outside the permissible range. |
| P01812A | - | The fuel temperature sensor has a malfunction. There is no signal change. |
| P018184 | - | The fuel temperature sensor has a malfunction. There is a signal below the permissible limit value. |
| P018185 | - | The fuel temperature sensor has a malfunction. There is a signal above the permissible limit value. |
| P018187 | - | This error code can be ignored and erased. |
| P018211 | - | The fuel temperature sensor has a short circuit to ground. There is a short circuit to ground. |
| P018312 | - | The fuel temperature sensor has a short circuit to positive. There is a short circuit to positive. |
| P019016 | - | The rail pressure sensor has an electrical fault. The limit value for electrical voltage has not been attained. |
| P019017 | - | The rail pressure sensor has an electrical fault. The limit value for electrical voltage has been exceeded. |
| P019116 | - | The rail pressure sensor has a malfunction. The limit value for electrical voltage has not been attained. |
| P019117 | - | The rail pressure sensor has a malfunction. The limit value for electrical voltage has been exceeded. |
| P019211 | - | The rail pressure sensor has a short circuit to ground. There is a short circuit to ground. |
| P019312 | - | The rail pressure sensor has a short circuit to positive. There is a short circuit to positive. |
| P019627 | - | Engine oil temperature sensor 1 has a malfunction. The signal change rate is above the permissible limit value. |
| P01962A | - | Engine oil temperature sensor 1 has a malfunction. There is no signal change. |
| P019661 | - | This error code can be ignored and erased. |
| P019692 | - | Engine oil temperature sensor 1 has a malfunction. The function or the instruction is faulty. |
| P019711 | - | Engine oil temperature sensor 1 has a short circuit to ground. There is a short circuit to ground. |
| P019812 | - | Engine oil temperature sensor 1 has a short circuit to positive. There is a short circuit to positive. |
| P019A00 | - | The lean/rich switchover of NOx sensor 1 (cylinder bank 1) is delayed. |
| P019B00 | - | The lean/rich switchover of NOx sensor 1 (cylinder bank 1) is delayed. |
| P019C00 | - | The lean/rich switchover of NOx sensor 1 (cylinder bank 2) is delayed. |
| P019D00 | - | The lean/rich switchover of NOx sensor 1 (cylinder bank 2) is delayed. |
| P020101 | - | The fuel injector (cylinder 1) has an electrical fault or an open circuit. There is a general electrical fault. |
| P020111 | - | The fuel injector (cylinder 1) has an electrical fault or an open circuit. There is a short circuit to ground. |
| P020113 | - | The fuel injector (cylinder 1) has an electrical fault or an open circuit. There is an open circuit. |
| P020119 | - | The fuel injector (cylinder 1) has an electrical fault or an open circuit. The limit value for current has been exceeded. |
| P02011F | - | The fuel injector (cylinder 1) has an electrical fault or an open circuit. There is a sporadic fault. |
| P020149 | - | The fuel injector (cylinder 1) has an electrical fault or an open circuit. There is an internal electrical fault. |
| P020192 | - | The fuel injector (cylinder 1) has an electrical fault or an open circuit. The function or the instruction is faulty. |
| P020201 | - | The fuel injector (cylinder 2) has an electrical fault or an open circuit. There is a general electrical fault. |
| P020211 | - | The fuel injector (cylinder 2) has an electrical fault or an open circuit. There is a short circuit to ground. |
| P020213 | - | The fuel injector (cylinder 2) has an electrical fault or an open circuit. There is an open circuit. |
| P020219 | - | The fuel injector (cylinder 2) has an electrical fault or an open circuit. The limit value for current has been exceeded. |
| P02021F | - | The fuel injector (cylinder 2) has an electrical fault or an open circuit. There is a sporadic fault. |
| P020249 | - | The fuel injector (cylinder 2) has an electrical fault or an open circuit. There is an internal electrical fault. |
| P020292 | - | The fuel injector (cylinder 2) has an electrical fault or an open circuit. The function or the instruction is faulty. |
| P020301 | - | The fuel injector (cylinder 3) has an electrical fault or an open circuit. There is a general electrical fault. |
| P020311 | - | The fuel injector (cylinder 3) has an electrical fault or an open circuit. There is a short circuit to ground. |
| P020313 | - | The fuel injector (cylinder 3) has an electrical fault or an open circuit. There is an open circuit. |
| P020319 | - | The fuel injector (cylinder 3) has an electrical fault or an open circuit. The limit value for current has been exceeded. |
| P02031F | - | The fuel injector (cylinder 3) has an electrical fault or an open circuit. There is a sporadic fault. |
| P020349 | - | The fuel injector (cylinder 3) has an electrical fault or an open circuit. There is an internal electrical fault. |
| P020392 | - | The fuel injector (cylinder 3) has an electrical fault or an open circuit. The function or the instruction is faulty. |
| P020401 | - | The fuel injector (cylinder 4) has an electrical fault or an open circuit. There is a general electrical fault. |
| P020411 | - | The fuel injector (cylinder 4) has an electrical fault or an open circuit. There is a short circuit to ground. |
| P020413 | - | The fuel injector (cylinder 4) has an electrical fault or an open circuit. There is an open circuit. |
| P020419 | - | The fuel injector (cylinder 4) has an electrical fault or an open circuit. The limit value for current has been exceeded. |
| P02041F | - | The fuel injector (cylinder 4) has an electrical fault or an open circuit. There is a sporadic fault. |
| P020449 | - | The fuel injector (cylinder 4) has an electrical fault or an open circuit. There is an internal electrical fault. |
| P020492 | - | The fuel injector (cylinder 4) has an electrical fault or an open circuit. The function or the instruction is faulty. |
| P020501 | - | The fuel injector (cylinder 5) has an electrical fault or an open circuit. There is a general electrical fault. |
| P020511 | - | The fuel injector (cylinder 5) has an electrical fault or an open circuit. There is a short circuit to ground. |
| P020513 | - | The fuel injector (cylinder 5) has an electrical fault or an open circuit. There is an open circuit. |
| P020519 | - | The fuel injector (cylinder 5) has an electrical fault or an open circuit. The limit value for current has been exceeded. |
| P02051F | - | The fuel injector (cylinder 5) has an electrical fault or an open circuit. There is a sporadic fault. |
| P020549 | - | The fuel injector (cylinder 5) has an electrical fault or an open circuit. There is an internal electrical fault. |
| P020592 | - | The fuel injector (cylinder 5) has an electrical fault or an open circuit. The function or the instruction is faulty. |
| P020601 | - | The fuel injector (cylinder 6) has an electrical fault or an open circuit. There is a general electrical fault. |
| P020611 | - | The fuel injector (cylinder 6) has an electrical fault or an open circuit. There is a short circuit to ground. |
| P020613 | - | The fuel injector (cylinder 6) has an electrical fault or an open circuit. There is an open circuit. |
| P020619 | - | The fuel injector (cylinder 6) has an electrical fault or an open circuit. The limit value for current has been exceeded. |
| P02061F | - | The fuel injector (cylinder 6) has an electrical fault or an open circuit. There is a sporadic fault. |
| P020649 | - | The fuel injector (cylinder 6) has an electrical fault or an open circuit. There is an internal electrical fault. |
| P020692 | - | The fuel injector (cylinder 6) has an electrical fault or an open circuit. The function or the instruction is faulty. |
| P020701 | - | The fuel injector (cylinder 7) has an electrical fault or an open circuit. There is a general electrical fault. |
| P020711 | - | The fuel injector (cylinder 7) has an electrical fault or an open circuit. There is a short circuit to ground. |
| P020713 | - | The fuel injector (cylinder 7) has an electrical fault or an open circuit. There is an open circuit. |
| P020719 | - | The fuel injector (cylinder 7) has an electrical fault or an open circuit. The limit value for current has been exceeded. |
| P02071F | - | The fuel injector (cylinder 7) has an electrical fault or an open circuit. There is a sporadic fault. |
| P020749 | - | The fuel injector (cylinder 7) has an electrical fault or an open circuit. There is an internal electrical fault. |
| P020792 | - | The fuel injector (cylinder 7) has an electrical fault or an open circuit. The function or the instruction is faulty. |
| P020801 | - | The fuel injector (cylinder 8) has an electrical fault or an open circuit. There is a general electrical fault. |
| P020811 | - | The fuel injector (cylinder 8) has an electrical fault or an open circuit. There is a short circuit to ground. |
| P020813 | - | The fuel injector (cylinder 8) has an electrical fault or an open circuit. There is an open circuit. |
| P020819 | - | The fuel injector (cylinder 8) has an electrical fault or an open circuit. The limit value for current has been exceeded. |
| P02081F | - | The fuel injector (cylinder 8) has an electrical fault or an open circuit. There is a sporadic fault. |
| P020849 | - | The fuel injector (cylinder 8) has an electrical fault or an open circuit. There is an internal electrical fault. |
| P020892 | - | The fuel injector (cylinder 8) has an electrical fault or an open circuit. The function or the instruction is faulty. |
| P021700 | - | The coolant temperature of the engine is too high. |
| P021900 | - | The engine speed is too high. |
| P021935 | - | The engine speed is too high. The on-time of the signal frequency is too long. |
| P022200 | - | Position sensor 2 for the throttle valve has a short circuit to ground. |
| P022300 | - | Position sensor 2 for the throttle valve has a short circuit to positive. |
| P023400 | - | The boost pressure of turbocharger 1 is too high. |
| P023409 | - | The boost pressure of turbocharger 1 is too high. There is a component fault. |
| P023616 | - | The boost pressure sensor has a malfunction. The limit value for electrical voltage has not been attained. |
| P023617 | - | The boost pressure sensor has a malfunction. The limit value for electrical voltage has been exceeded. |
| P023628 | - | The boost pressure sensor has a malfunction. The signal offset is outside the permissible range. |
| P023664 | - | The boost pressure sensor has a malfunction. There is an implausible signal. |
| P023711 | - | The boost pressure sensor has a short circuit to ground. There is a short circuit to ground. |
| P023812 | - | The boost pressure sensor has a short circuit to positive. There is a short circuit to positive. |
| P023A00 | - | Actuation 'Coolant pump of charge air cooler' has an electrical fault or open circuit. |
| P023B00 | - | Actuation 'Coolant pump of charge air cooler' has a short circuit to ground. |
| P023C00 | - | Actuation 'Coolant pump of charge air cooler' has a short circuit to positive. |
| P024300 | - | The output for the low-pressure turbocharger has an electrical fault. |
| P024313 | - | The output for the low-pressure turbocharger has an electrical fault. There is an open circuit. |
| P024500 | - | The output for the low-pressure turbocharger has a short circuit to ground. |
| P024511 | - | The output for the low-pressure turbocharger has a short circuit to ground. There is a short circuit to ground. |
| P024600 | - | The output for the low-pressure turbocharger has a short circuit to positive. |
| P024612 | - | The output for the low-pressure turbocharger has a short circuit to positive. There is a short circuit to positive. |
| P024700 | - | This error code can be ignored and erased. |
| P024713 | - | This error code can be ignored and erased. |
| P024900 | - | This error code can be ignored and erased. |
| P024911 | - | This error code can be ignored and erased. |
| P025000 | - | This error code can be ignored and erased. |
| P025012 | - | This error code can be ignored and erased. |
| P026212 | - | The fuel injector (cylinder 1) has a short circuit to positive. There is a short circuit to positive. |
| P026512 | - | The fuel injector (cylinder 2) has a short circuit to positive. There is a short circuit to positive. |
| P026812 | - | The fuel injector (cylinder 3) has a short circuit to positive. There is a short circuit to positive. |
| P026A00 | - | The efficiency of the charge air cooler is not sufficient. |
| P027112 | - | The fuel injector (cylinder 4) has a short circuit to positive. There is a short circuit to positive. |
| P027412 | - | The fuel injector (cylinder 5) has a short circuit to positive. There is a short circuit to positive. |
| P027712 | - | The fuel injector (cylinder 6) has a short circuit to positive. There is a short circuit to positive. |
| P028012 | - | The fuel injector (cylinder 7) has a short circuit to positive. There is a short circuit to positive. |
| P028312 | - | The fuel injector (cylinder 8) has a short circuit to positive. There is a short circuit to positive. |
| P029900 | - | The boost pressure of turbocharger 1 is too low. |
| P029909 | - | The boost pressure of turbocharger 1 is too low. There is a component fault. |
| P030000 | - | Combustion misfiring has been detected. |
| P030022 | - | Combustion misfiring has been detected. The signal amplitude is greater than the maximum amplitude. |
| P030027 | - | Combustion misfiring has been detected. The signal change rate is above the permissible limit value. |
| P030084 | - | Combustion misfiring has been detected. There is a signal below the permissible limit value. |
| P030085 | - | Combustion misfiring has been detected. There is a signal above the permissible limit value. |
| P030100 | - | Combustion misfiring of cylinder 1 has been detected. |
| P030184 | - | Combustion misfiring of cylinder 1 has been detected. There is a signal below the permissible limit value. |
| P030185 | - | Combustion misfiring of cylinder 1 has been detected. There is a signal above the permissible limit value. |
| P030200 | - | Combustion misfiring of cylinder 2 has been detected. |
| P030284 | - | Combustion misfiring of cylinder 2 has been detected. There is a signal below the permissible limit value. |
| P030285 | - | Combustion misfiring of cylinder 2 has been detected. There is a signal above the permissible limit value. |
| P030300 | - | Combustion misfiring of cylinder 3 has been detected. |
| P030384 | - | Combustion misfiring of cylinder 3 has been detected. There is a signal below the permissible limit value. |
| P030385 | - | Combustion misfiring of cylinder 3 has been detected. There is a signal above the permissible limit value. |
| P030400 | - | Combustion misfiring of cylinder 4 has been detected. |
| P030484 | - | Combustion misfiring of cylinder 4 has been detected. There is a signal below the permissible limit value. |
| P030485 | - | Combustion misfiring of cylinder 4 has been detected. There is a signal above the permissible limit value. |
| P030500 | - | Combustion misfiring of cylinder 5 has been detected. |
| P030584 | - | Combustion misfiring of cylinder 5 has been detected. There is a signal below the permissible limit value. |
| P030585 | - | Combustion misfiring of cylinder 5 has been detected. There is a signal above the permissible limit value. |
| P030600 | - | Combustion misfiring of cylinder 6 has been detected. |
| P030684 | - | Combustion misfiring of cylinder 6 has been detected. There is a signal below the permissible limit value. |
| P030685 | - | Combustion misfiring of cylinder 6 has been detected. There is a signal above the permissible limit value. |
| P030700 | - | Combustion misfiring of cylinder 7 has been detected. |
| P030784 | - | Combustion misfiring of cylinder 7 has been detected. There is a signal below the permissible limit value. |
| P030785 | - | Combustion misfiring of cylinder 7 has been detected. There is a signal above the permissible limit value. |
| P030800 | - | Combustion misfiring of cylinder 8 has been detected. |
| P030884 | - | Combustion misfiring of cylinder 8 has been detected. There is a signal below the permissible limit value. |
| P030885 | - | Combustion misfiring of cylinder 8 has been detected. There is a signal above the permissible limit value. |
| P032400 | - | The knock control has a malfunction. |
| P032427 | - | The knock control has a malfunction. The signal change rate is above the permissible limit value. |
| P032711 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground. |
| P032714 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground or an open circuit. |
| P032784 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to ground. There is a signal below the permissible limit value. |
| P032812 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive. |
| P032815 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P032885 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to positive. There is a signal above the permissible limit value. |
| P032C11 | - | Knock sensor 2 (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground. |
| P032C14 | - | Knock sensor 2 (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground or an open circuit. |
| P032C84 | - | Knock sensor 2 (cylinder bank 1) has a short circuit to ground. There is a signal below the permissible limit value. |
| P032D12 | - | Knock sensor 2 (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive. |
| P032D15 | - | Knock sensor 2 (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P032D85 | - | Knock sensor 2 (cylinder bank 1) has a short circuit to positive. There is a signal above the permissible limit value. |
| P033211 | - | Knock sensor 1 (cylinder bank 2) has a short circuit to ground. There is a short circuit to ground. |
| P033214 | - | Knock sensor 1 (cylinder bank 2) has a short circuit to ground. There is a short circuit to ground or an open circuit. |
| P033284 | - | Knock sensor 1 (cylinder bank 2) has a short circuit to ground. There is a signal below the permissible limit value. |
| P033312 | - | Knock sensor 1 (cylinder bank 2) has a short circuit to positive. There is a short circuit to positive. |
| P033315 | - | Knock sensor 1 (cylinder bank 2) has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P033385 | - | Knock sensor 1 (cylinder bank 2) has a short circuit to positive. There is a signal above the permissible limit value. |
| P033500 | - | Position sensor 1 for the crankshaft has an electrical fault. |
| P033502 | - | Position sensor 1 for the crankshaft has an electrical fault. There is a general signal fault. |
| P033900 | - | Position sensor 1 for the crankshaft has a sporadic malfunction. |
| P033901 | - | Position sensor 1 for the crankshaft has a sporadic malfunction. There is a general electrical fault. |
| P033902 | - | Position sensor 1 for the crankshaft has a sporadic malfunction. There is a general signal fault. |
| P033903 | - | Position sensor 1 for the crankshaft has a sporadic malfunction. There is a frequency or pulse width modulation fault. |
| P033904 | - | Position sensor 1 for the crankshaft has a sporadic malfunction. There is an internal fault. |
| P033905 | - | Position sensor 1 for the crankshaft has a sporadic malfunction. There is a programming fault. |
| P033906 | - | Position sensor 1 for the crankshaft has a sporadic malfunction. There is an algorithm fault. |
| P033C11 | - | Knock sensor 2 (cylinder bank 2) has a short circuit to ground. There is a short circuit to ground. |
| P033C14 | - | Knock sensor 2 (cylinder bank 2) has a short circuit to ground. There is a short circuit to ground or an open circuit. |
| P033C84 | - | Knock sensor 2 (cylinder bank 2) has a short circuit to ground. There is a signal below the permissible limit value. |
| P033D12 | - | Knock sensor 2 (cylinder bank 2) has a short circuit to positive. There is a short circuit to positive. |
| P033D15 | - | Knock sensor 2 (cylinder bank 2) has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P033D85 | - | Knock sensor 2 (cylinder bank 2) has a short circuit to positive. There is a signal above the permissible limit value. |
| P034100 | - | The position sensor for the intake camshaft (cylinder bank 1) has a malfunction. |
| P034200 | - | The position sensor for the intake camshaft (cylinder bank 1) has a short circuit to ground. |
| P034300 | - | The position sensor for the intake camshaft (cylinder bank 1) has a short circuit to positive. |
| P034600 | - | The position sensor for the intake camshaft (cylinder bank 2) has a malfunction. |
| P034700 | - | The position sensor for the intake camshaft (cylinder bank 2) has a short circuit to ground. |
| P034800 | - | The position sensor for the intake camshaft (cylinder bank 2) has a short circuit to positive. |
| P035107 | - | This error code can be ignored and erased. |
| P035113 | - | The actuation of ignition coil 1 has an electrical fault or open circuit. There is an open circuit. |
| P035149 | - | The actuation of ignition coil 1 has an electrical fault or open circuit. There is an internal electrical fault. |
| P035196 | - | The actuation of ignition coil 1 has an electrical fault or open circuit. There is an internal component fault. |
| P035207 | - | This error code can be ignored and erased. |
| P035213 | - | The actuation of ignition coil 2 has an electrical fault or open circuit. There is an open circuit. |
| P035249 | - | The actuation of ignition coil 2 has an electrical fault or open circuit. There is an internal electrical fault. |
| P035296 | - | The actuation of ignition coil 2 has an electrical fault or open circuit. There is an internal component fault. |
| P035307 | - | This error code can be ignored and erased. |
| P035313 | - | The actuation of ignition coil 3 has an electrical fault or open circuit. There is an open circuit. |
| P035349 | - | The actuation of ignition coil 3 has an electrical fault or open circuit. There is an internal electrical fault. |
| P035396 | - | The actuation of ignition coil 3 has an electrical fault or open circuit. There is an internal component fault. |
| P035407 | - | This error code can be ignored and erased. |
| P035413 | - | The actuation of ignition coil 4 has an electrical fault or open circuit. There is an open circuit. |
| P035449 | - | The actuation of ignition coil 4 has an electrical fault or open circuit. There is an internal electrical fault. |
| P035496 | - | The actuation of ignition coil 4 has an electrical fault or open circuit. There is an internal component fault. |
| P035507 | - | This error code can be ignored and erased. |
| P035513 | - | The actuation of ignition coil 5 has an electrical fault or open circuit. There is an open circuit. |
| P035549 | - | The actuation of ignition coil 5 has an electrical fault or open circuit. There is an internal electrical fault. |
| P035596 | - | The actuation of ignition coil 5 has an electrical fault or open circuit. There is an internal component fault. |
| P035607 | - | This error code can be ignored and erased. |
| P035613 | - | The actuation of ignition coil 6 has an electrical fault or open circuit. There is an open circuit. |
| P035649 | - | The actuation of ignition coil 6 has an electrical fault or open circuit. There is an internal electrical fault. |
| P035696 | - | The actuation of ignition coil 6 has an electrical fault or open circuit. There is an internal component fault. |
| P035707 | - | This error code can be ignored and erased. |
| P035713 | - | The actuation of ignition coil 7 has an electrical fault or open circuit. There is an open circuit. |
| P035749 | - | The actuation of ignition coil 7 has an electrical fault or open circuit. There is an internal electrical fault. |
| P035796 | - | The actuation of ignition coil 7 has an electrical fault or open circuit. There is an internal component fault. |
| P035807 | - | This error code can be ignored and erased. |
| P035813 | - | The actuation of ignition coil 8 has an electrical fault or open circuit. There is an open circuit. |
| P035849 | - | The actuation of ignition coil 8 has an electrical fault or open circuit. There is an internal electrical fault. |
| P035896 | - | The actuation of ignition coil 8 has an electrical fault or open circuit. There is an internal component fault. |
| P036300 | - | Injector shutoff was activated due to a combustion misfire. |
| P036600 | - | The position sensor for the exhaust camshaft (cylinder bank 1) has a malfunction. |
| P036700 | - | The position sensor for the exhaust camshaft (cylinder bank 1) has a short circuit to ground. |
| P036800 | - | The position sensor for the exhaust camshaft (cylinder bank 1) has a short circuit to positive. |
| P039100 | - | The position sensor for the exhaust camshaft (cylinder bank 2) has a malfunction. |
| P039200 | - | The position sensor for the exhaust camshaft (cylinder bank 2) has a short circuit to ground. |
| P039300 | - | The position sensor for the exhaust camshaft (cylinder bank 2) has a short circuit to positive. |
| P040300 | - | The actuation for the exhaust gas recirculation controller (cylinder bank 1) has an electrical fault. |
| P040319 | - | The actuation for the exhaust gas recirculation controller (cylinder bank 1) has an electrical fault. The limit value for current has been exceeded. |
| P040464 | - | The actuation for the exhaust gas recirculation controller (cylinder bank 1) has a malfunction. There is an implausible signal. |
| P040477 | - | The actuation for the exhaust gas recirculation controller (cylinder bank 1) has a malfunction. The commanded position cannot be reached. |
| P040478 | - | The actuation for the exhaust gas recirculation controller (cylinder bank 1) has a malfunction. The adaptation or adjustment is incorrect. |
| P040492 | - | The actuation for the exhaust gas recirculation controller (cylinder bank 1) has a malfunction. The function or the instruction is faulty. |
| P040500 | - | The position sensor for the exhaust gas recirculation controller (cylinder bank 1) has a short circuit to ground. |
| P040600 | - | The position sensor for the exhaust gas recirculation controller (cylinder bank 1) has a short circuit to positive. |
| P040700 | - | The position sensor for the exhaust gas recirculation controller (cylinder bank 2) has a short circuit to ground. |
| P040800 | - | The position sensor for the exhaust gas recirculation controller (cylinder bank 2) has a short circuit to positive. |
| P041B27 | - | Temperature sensor 2 of the exhaust gas recirculation has a malfunction. The signal change rate is above the permissible limit value. |
| P041B28 | - | Temperature sensor 2 of the exhaust gas recirculation has a malfunction. The signal offset is outside the permissible range. |
| P041B2A | - | Temperature sensor 2 of the exhaust gas recirculation has a malfunction. There is no signal change. |
| P041C11 | - | Temperature sensor 2 of the exhaust gas recirculation has a short circuit to ground. There is a short circuit to ground. |
| P041D12 | - | Temperature sensor 2 of the exhaust gas recirculation has a short circuit to positive. There is a short circuit to positive. |
| P042000 | - | The efficiency of the catalytic converter (cylinder bank 1) is not sufficient. |
| P04252A | - | Temperature sensor 1 'Catalytic converter' (cylinder bank 1) has an electrical fault. There is no signal change. |
| P042627 | - | Temperature sensor 1 'Catalytic converter' (cylinder bank 1) has a malfunction. The signal change rate is above the permissible limit value. |
| P042628 | - | Temperature sensor 1 'Catalytic converter' (cylinder bank 1) has a malfunction. The signal offset is outside the permissible range. |
| P042662 | - | Temperature sensor 1 'Catalytic converter' (cylinder bank 1) has a malfunction. The signal comparison is faulty. |
| P042711 | - | Temperature sensor 1 'Catalytic converter' (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground. |
| P042812 | - | Temperature sensor 1 'Catalytic converter' (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive. |
| P042E72 | - | The exhaust gas recirculation controller (cylinder bank 1) is jammed open. The actuator does not close. |
| P042E92 | - | The exhaust gas recirculation controller (cylinder bank 1) is jammed open. The function or the instruction is faulty. |
| P042F73 | - | The exhaust gas recirculation controller (cylinder bank 1) is jammed closed. The actuator does not open. |
| P042F97 | - | The exhaust gas recirculation controller (cylinder bank 1) is jammed closed. The system function is restricted. |
| P043000 | - | The efficiency of the catalytic converter (cylinder bank 2) is not sufficient. |
| P043500 | - | Temperature sensor 1 'Catalytic converter' (cylinder bank 2) has an electrical fault. |
| P043504 | - | Temperature sensor 1 'Catalytic converter' (cylinder bank 2) has an electrical fault. There is an internal fault. |
| P04352A | - | Temperature sensor 1 'Catalytic converter' (cylinder bank 2) has an electrical fault. There is no signal change. |
| P043627 | - | Temperature sensor 1 'catalytic converter' (cylinder bank 2) has a malfunction. The signal change rate is above the permissible limit value. |
| P043628 | - | Temperature sensor 1 'catalytic converter' (cylinder bank 2) has a malfunction. The signal offset is outside the permissible range. |
| P043662 | - | Temperature sensor 1 'catalytic converter' (cylinder bank 2) has a malfunction. The signal comparison is faulty. |
| P043711 | - | Temperature sensor 1 'Catalytic converter' (cylinder bank 2) has a short circuit to ground. There is a short circuit to ground. |
| P043812 | - | Temperature sensor 1 'Catalytic converter' (cylinder bank 2) has a short circuit to positive. There is a short circuit to positive. |
| P044200 | - | A fine leak in the evaporative emission control system was detected. |
| P044209 | - | This error code can be ignored and erased. |
| P04427A | - | A fine leak in the evaporative emission control system was detected. Leakage or a defective seal was detected. |
| P044400 | - | The purge valve of the evaporative emission control system has an open circuit. |
| P044700 | - | The shutoff valve of the activated charcoal canister has an open circuit. |
| P045002 | - | The pressure sensor/pressure switch of the evaporative emission control system has an electrical fault. There is a general signal fault. |
| P045100 | - | This error code can be ignored and erased. |
| P045101 | - | This error code can be ignored and erased. |
| P045111 | - | This error code can be ignored and erased. |
| P045112 | - | This error code can be ignored and erased. |
| P045116 | - | This error code can be ignored and erased. |
| P045117 | - | This error code can be ignored and erased. |
| P045124 | - | The pressure sensor/pressure switch of the evaporative emission control system has a malfunction. No signal change: Voltage level is too high. |
| P045126 | - | The pressure sensor/pressure switch of the evaporative emission control system has a malfunction. The signal change rate is below the permissible limit value. |
| P045128 | - | The pressure sensor/pressure switch of the evaporative emission control system has a malfunction. The signal offset is outside the permissible range. |
| P045129 | - | This error code can be ignored and erased. |
| P045200 | - | The pressure sensor/pressure switch of the evaporative emission control system has a short circuit to ground. |
| P045300 | - | The pressure sensor/pressure switch of the evaporative emission control system has a short circuit to positive. |
| P045500 | - | A gross leak in the evaporative emission control system was detected. |
| P045509 | - | This error code can be ignored and erased. |
| P045600 | - | A very fine leak in the evaporative emission control system was detected. |
| P045604 | - | This error code can be ignored and erased. |
| P045609 | - | This error code can be ignored and erased. |
| P04567A | - | A very fine leak in the evaporative emission control system was detected. Leakage or a defective seal was detected. |
| P045700 | - | Leakage in the evaporative emission control system was detected (tank cap missing). |
| P045709 | - | Leakage in the evaporative emission control system was detected (tank cap missing). There is a component fault. |
| P04577A | - | Leakage in the evaporative emission control system was detected (tank cap missing). Leakage or a defective seal was detected. |
| P045800 | - | The purge valve of the evaporative emission control system has a short circuit to ground. |
| P045900 | - | The purge valve of the evaporative emission control system has a short circuit to positive. |
| P045A00 | - | The actuation for the exhaust gas recirculation controller (cylinder bank 2) has an electrical fault. |
| P045A19 | - | The actuation for the exhaust gas recirculation controller (cylinder bank 2) has an electrical fault. The limit value for current has been exceeded. |
| P045B64 | - | The actuation for the exhaust gas recirculation controller (cylinder bank 2) has a malfunction. There is an implausible signal. |
| P045B77 | - | The actuation for the exhaust gas recirculation controller (cylinder bank 2) has a malfunction. The commanded position cannot be reached. |
| P045B78 | - | The actuation for the exhaust gas recirculation controller (cylinder bank 2) has a malfunction. The adaptation or adjustment is incorrect. |
| P045B92 | - | The actuation for the exhaust gas recirculation controller (cylinder bank 2) has a malfunction. The function or the instruction is faulty. |
| P045E72 | - | The exhaust gas recirculation controller (cylinder bank 2) is jammed open. The actuator does not close. |
| P045E92 | - | The exhaust gas recirculation controller (cylinder bank 2) is jammed open. The function or the instruction is faulty. |
| P045F73 | - | The exhaust gas recirculation controller (cylinder bank 2) is jammed closed. The actuator does not open. |
| P045F97 | - | The exhaust gas recirculation controller (cylinder bank 2) is jammed closed. The system function is restricted. |
| P04608F | - | The left fuel level sensor has an electrical fault. The signal or message is erratic. |
| P046100 | - | The left fuel level sensor has a malfunction. |
| P04612A | - | The left fuel level sensor has a malfunction. There is no signal change. |
| P046184 | - | The left fuel level sensor has a malfunction. There is a signal below the permissible limit value. |
| P046185 | - | The left fuel level sensor has a malfunction. There is a signal above the permissible limit value. |
| P046211 | - | The left fuel level sensor has a short circuit to ground. There is a short circuit to ground. |
| P046312 | - | The left fuel level sensor has a short circuit to positive. There is a short circuit to positive. |
| P046C00 | - | The position sensor for the exhaust gas recirculation controller (cylinder bank 1) has a malfunction. |
| P046C09 | - | The position sensor for the exhaust gas recirculation controller (cylinder bank 1) has a malfunction. There is a component fault. |
| P046E00 | - | The position sensor for the exhaust gas recirculation controller (cylinder bank 2) has a malfunction. |
| P046E09 | - | The position sensor for the exhaust gas recirculation controller (cylinder bank 2) has a malfunction. There is a component fault. |
| P047100 | - | This error code can be ignored and erased. |
| P047128 | - | Exhaust back pressure sensor 1 has a malfunction. The signal offset is outside the permissible range. |
| P04712A | - | Exhaust back pressure sensor 1 has a malfunction. There is no signal change. |
| P047200 | - | Exhaust back pressure sensor 1 has a short circuit to ground. |
| P047300 | - | Exhaust back pressure sensor 1 has a short circuit to positive. |
| P047B00 | - | This error code can be ignored and erased. |
| P047B28 | - | Exhaust back pressure sensor 2 has a malfunction. The signal offset is outside the permissible range. |
| P047B2A | - | Exhaust back pressure sensor 2 has a malfunction. There is no signal change. |
| P047C00 | - | Exhaust back pressure sensor 2 has a short circuit to ground. |
| P047D00 | - | Exhaust back pressure sensor 2 has a short circuit to positive. |
| P048000 | - | The output of electric fan 1 has an electrical fault or an open circuit. |
| P048013 | - | This error code can be ignored and erased. |
| P048300 | - | Electric fan has a malfunction. |
| P048309 | - | The electric fan has a malfunction. There is a component fault. |
| P048568 | - | The power supply or ground connection of the electric fan has a malfunction. There is incomplete information. |
| P048708 | - | The output for the exhaust gas recirculation actuator (cylinder bank 1) has an electrical fault or open circuit. There is a signal fault or the message is faulty. |
| P049600 | - | The purge flow of the evaporative emission control system is too high. |
| P049697 | - | This error code can be ignored and erased. |
| P049700 | - | The purge flow of the of evaporative emission control system is too low. |
| P049792 | - | This error code can be ignored and erased. |
| P049800 | - | The shutoff valve of the activated charcoal canister has a short circuit to ground. |
| P049900 | - | The shutoff valve of the activated charcoal canister has a short circuit to positive. |
| P04F000 | - | Standard-Fehlercode |
| P050000 | - | Speed sensor 1 has a malfunction. |
| P050008 | - | Speed sensor 1 has a malfunction. There is a signal fault or the message is faulty. |
| P050500 | - | Idle speed control has a malfunction. |
| P050600 | - | Idle speed too low when the internal combustion engine is hot. |
| P050700 | - | Idle speed too high when the internal combustion engine is hot. |
| P050A92 | - | Idle speed control has a malfunction during a cold start. The function or the instruction is faulty. |
| P050A94 | - | Idle speed control has a malfunction during a cold start. There is an unexpected instruction. |
| P050B00 | - | Ignition angle setting has a malfunction during a cold start. |
| P050C62 | - | The coolant temperature of the combustion engine is implausible during a cold start. The signal comparison is faulty. |
| P050C64 | - | The coolant temperature of the combustion engine is implausible during a cold start. There is an implausible signal. |
| P050D00 | - | The combustion engine idles roughly after a cold start. |
| P051136 | - | The idle speed control has an electrical fault. The signal frequency is too low. |
| P051192 | - | The idle speed control has an electrical fault. The function or the instruction is faulty. |
| P051194 | - | The idle speed control has an electrical fault. There is an unexpected instruction. |
| P051200 | - | Start enable has a malfunction. |
| P051204 | - | Start enable has a malfunction. There is an internal fault. |
| P051301 | - | Start enable was not issued. There is a general electrical fault. |
| P051302 | - | Start enable was not issued. There is a general signal fault. |
| P051303 | - | Start enable was not issued. There is a frequency or pulse width modulation fault. |
| P051304 | - | Start enable was not issued. There is an internal fault. |
| P051305 | - | Start enable was not issued. There is a programming fault. |
| P051306 | - | Start enable was not issued. There is an algorithm fault. |
| P051307 | - | Start enable was not issued. There is a mechanical fault. |
| P051308 | - | Start enable was not issued. There is a signal fault or the message is faulty. |
| P051309 | - | Start enable was not issued. There is a component fault. |
| P051310 | - | Start enable was not issued. Reserved for ISO/SAE |
| P051311 | - | Start enable was not issued. There is a short circuit to ground. |
| P051312 | - | Start enable was not issued. There is a short circuit to positive. |
| P051313 | - | Start enable was not issued. There is an open circuit. |
| P051314 | - | Start enable was not issued. There is a short circuit to ground or an open circuit. |
| P051315 | - | Start enable was not issued. There is a short circuit to positive or an open circuit. |
| P051316 | - | Start enable was not issued. The limit value for electrical voltage has not been attained. |
| P052100 | - | The engine oil pressure sensor has a malfunction. |
| P052200 | - | The engine oil pressure sensor has a short circuit to ground. |
| P052300 | - | The engine oil pressure sensor has a short circuit to positive. |
| P052400 | - | Oil pressure is too low. |
| P052A00 | - | The position of the intake camshaft (cylinder bank 1) deviates from the specified value in direction 'Advanced' during cold start. |
| P052C00 | - | The position of the intake camshaft (cylinder bank 2) deviates from the specified value in direction 'Advanced' during cold start. |
| P053200 | - | This error code can be ignored and erased. |
| P053300 | - | This error code can be ignored and erased. |
| P053400 | - | This error code can be ignored and erased. |
| P053600 | - | This error code can be ignored and erased. |
| P053700 | - | This error code can be ignored and erased. |
| P053800 | - | This error code can be ignored and erased. |
| P053F92 | - | The fuel pressure during a cold start is implausible. The function or the instruction is faulty. |
| P053F94 | - | The fuel pressure during a cold start is implausible. There is an unexpected instruction. |
| P054A00 | - | The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value during cold start. |
| P054C00 | - | The position of the intake camshaft (cylinder bank 1) deviates from the specified value during cold start. |
| P056000 | - | This error code can be ignored and erased. |
| P056001 | - | This error code can be ignored and erased. |
| P056002 | - | The on-board electrical system voltage has a malfunction. There is a general signal fault. |
| P05601C | - | This error code can be ignored and erased. |
| P056200 | - | The on-board power supply voltage is too low. |
| P056216 | - | The on-board power supply voltage is too low. The limit value for electrical voltage has not been attained. |
| P056300 | - | The on-board power supply voltage is too high. |
| P056317 | - | The on-board power supply voltage is too high. The limit value for electrical voltage has been exceeded. |
| P057108 | - | Switch 'Brake light' has a malfunction. There is a signal fault or the message is faulty. |
| P057129 | - | Switch 'Brake light' has a malfunction. There is an invalid signal. |
| P057164 | - | Switch 'Brake light' has a malfunction. There is an implausible signal. |
| P057529 | - | Input 'CRUISE CONTROL' has an electrical fault. There is an invalid signal. |
| P059700 | - | The coolant thermostat has an electrical fault or open circuit. |
| P059800 | - | The coolant thermostat has a short circuit to ground. |
| P059900 | - | The coolant thermostat has a short circuit to positive. |
| P060400 | - | There is an internal control unit fault in the RAM memory. |
| P060404 | - | There is an internal control unit fault in the RAM memory. There is an internal fault. |
| P060405 | - | There is an internal control unit fault in the RAM memory. There is a programming fault. |
| P060416 | - | There is an internal control unit fault in the RAM memory. The limit value for electrical voltage has not been attained. |
| P060417 | - | There is an internal control unit fault in the RAM memory. The limit value for electrical voltage has been exceeded. |
| P060600 | - | There is an internal control unit fault in the processor. |
| P060700 | - | This error code can be ignored and erased. |
| P060704 | - | This error code can be ignored and erased. |
| P060709 | - | The control unit has a malfunction. There is a component fault. |
| P060710 | - | The control unit has a malfunction. Reserved for ISO/SAE |
| P060711 | - | The control unit has a malfunction. There is a short circuit to ground. |
| P060712 | - | The control unit has a malfunction. There is a short circuit to positive. |
| P060713 | - | The control unit has a malfunction. There is an open circuit. |
| P060714 | - | The control unit has a malfunction. There is a short circuit to ground or an open circuit. |
| P060715 | - | The control unit has a malfunction. There is a short circuit to positive or an open circuit. |
| P060716 | - | The control unit has a malfunction. The limit value for electrical voltage has not been attained. |
| P060717 | - | The control unit has a malfunction. The limit value for electrical voltage has been exceeded. |
| P060718 | - | The control unit has a malfunction. The limit value for current has not been attained. |
| P060719 | - | The control unit has a malfunction. The limit value for current has been exceeded. |
| P060741 | - | The control unit has a malfunction. There is a general checksum error. |
| P060748 | - | The control unit has a malfunction. There is an error in the control memory. |
| P060762 | - | The control unit has a malfunction. The signal comparison is faulty. |
| P060764 | - | The control unit has a malfunction. There is an implausible signal. |
| P060796 | - | The control unit has a malfunction. There is an internal component fault. |
| P060B00 | - | There is an internal control unit fault in the analog/digital converter. |
| P060C02 | - | There is an internal control unit fault in the central processing unit. There is a general signal fault. |
| P060C04 | - | There is an internal control unit fault in the central processing unit. There is an internal fault. |
| P060C09 | - | There is an internal control unit fault in the central processing unit. There is a component fault. |
| P060C17 | - | There is an internal control unit fault in the central processing unit. The limit value for electrical voltage has been exceeded. |
| P060C29 | - | There is an internal control unit fault in the central processing unit. There is an invalid signal. |
| P060C47 | - | There is an internal control unit fault in the central processing unit. There is a runtime error. |
| P060D00 | - | There is an internal control unit fault affecting the calculation of the accelerator pedal position. |
| P060D64 | - | There is an internal control unit fault affecting the calculation of the accelerator pedal position. There is an implausible signal. |
| P061100 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). |
| P061101 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a general electrical fault. |
| P061102 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a general signal fault. |
| P061103 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a frequency or pulse width modulation fault. |
| P061104 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is an internal fault. |
| P061105 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a programming fault. |
| P061106 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is an algorithm fault. |
| P061107 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a mechanical fault. |
| P061108 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a signal fault or the message is faulty. |
| P061109 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a component fault. |
| P061113 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is an open circuit. |
| P061116 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The limit value for electrical voltage has not been attained. |
| P061117 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The limit value for electrical voltage has been exceeded. |
| P061142 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a general memory error. |
| P061149 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is an internal electrical fault. |
| P06114A | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The wrong component is installed. |
| P061165 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The signal has too few transitions or events. |
| P061167 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The signal is impermissible after an event. |
| P061188 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). Bus OFF |
| P061192 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The function or the instruction is faulty. |
| P061194 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is an unexpected instruction. |
| P061196 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is an internal component fault. |
| P061242 | - | The relay actuation of control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a general memory error. |
| P06124A | - | The relay actuation of control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The wrong component is installed. |
| P061265 | - | The relay actuation of control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The signal has too few transitions or events. |
| P061267 | - | The relay actuation of control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The signal is impermissible after an event. |
| P061288 | - | The relay actuation of control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). Bus OFF |
| P061296 | - | The relay actuation of control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is an internal component fault. |
| P061408 | - | This error code can be ignored and erased. |
| P061487 | - | This error code can be ignored and erased. |
| P061513 | - | The starter relay has an electrical fault. There is an open circuit. |
| P061605 | - | The starter relay has a short circuit to ground. There is a programming fault. |
| P061606 | - | The starter relay has a short circuit to ground. There is an algorithm fault. |
| P061614 | - | The starter relay has a short circuit to ground. There is a short circuit to ground or an open circuit. |
| P061703 | - | The starter relay has a short circuit to positive. There is a frequency or pulse width modulation fault. |
| P061704 | - | The starter relay has a short circuit to positive. There is an internal fault. |
| P061715 | - | The starter relay has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P061A26 | - | The torque control of the control unit has a malfunction. The signal change rate is below the permissible limit value. |
| P061A27 | - | The torque control of the control unit has a malfunction. The signal change rate is above the permissible limit value. |
| P061A28 | - | The torque control of the control unit has a malfunction. The signal offset is outside the permissible range. |
| P061A61 | - | The torque control of the control unit has a malfunction. The signal calculation is faulty. |
| P061A62 | - | The torque control of the control unit has a malfunction. The signal comparison is faulty. |
| P061B00 | - | The torque calculation of the control unit has a malfunction. |
| P061B01 | - | The torque calculation of the control unit has a malfunction. There is a general electrical fault. |
| P061B04 | - | This error code can be ignored and erased. |
| P061B05 | - | This error code can be ignored and erased. |
| P061B06 | - | This error code can be ignored and erased. |
| P061B08 | - | The torque calculation of the control unit has a malfunction. There is a signal fault or the message is faulty. |
| P061B85 | - | The torque calculation of the control unit has a malfunction. There is a signal above the permissible limit value. |
| P061C00 | - | There is an internal control unit fault affecting the calculation of the engine speed. |
| P061C02 | - | There is an internal control unit fault affecting the calculation of the engine speed. There is a general signal fault. |
| P061C04 | - | There is an internal control unit fault affecting the calculation of the engine speed. There is an internal fault. |
| P061D00 | - | There is an internal control unit fault in the monitoring function for the air mass. |
| P061D46 | - | There is an internal control unit fault in the monitoring function for the air mass. There is an error in the calibration or parameterization memory. |
| P061D64 | - | There is an internal control unit fault in the monitoring function for the air mass. There is an implausible signal. |
| P062700 | - | The output for the fuel pump has an electrical fault or open circuit. |
| P062713 | - | The output for the fuel pump has an electrical fault or open circuit. There is an open circuit. |
| P062800 | - | The output for the fuel pump has a short circuit to ground. |
| P062811 | - | The output for the fuel pump has a short circuit to ground. There is a short circuit to ground. |
| P062900 | - | The output for the fuel pump has a short circuit to positive. |
| P062A00 | - | The output of the fuel pump is implausible. |
| P062B00 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. |
| P062B62 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. The signal comparison is faulty. |
| P062B63 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. The duration of the actuation was exceeded: overload protection is active. |
| P062B64 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. There is an implausible signal. |
| P062B66 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. The signal has too many transitions or events. |
| P062B68 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. There is incomplete information. |
| P062C00 | - | This error code can be ignored and erased. |
| P062F04 | - | This error code can be ignored and erased. |
| P062F05 | - | This error code can be ignored and erased. |
| P062F06 | - | This error code can be ignored and erased. |
| P063400 | - | The temperature in the control unit is too high. |
| P063884 | - | This error code can be ignored and erased. |
| P063885 | - | This error code can be ignored and erased. |
| P063E07 | - | The throttle valve adaptation has a malfunction. There is a mechanical fault. |
| P064104 | - | Output 1 for the reference voltage of the sensors has an electrical fault or an open circuit. There is an internal fault. |
| P064200 | - | Output 1 for the reference voltage of the sensors has a short circuit to ground. |
| P064300 | - | Output 1 for the reference voltage of the sensors has a short circuit to positive. |
| P064D04 | - | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. There is an internal fault. |
| P064D84 | - | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. There is a signal below the permissible limit value. |
| P064D85 | - | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. There is a signal above the permissible limit value. |
| P064D86 | - | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. There is an incorrect signal. |
| P064E04 | - | The processor of the oxygen sensor (cylinder bank 2) in the control unit has a malfunction. There is an internal fault. |
| P064E84 | - | The processor of the oxygen sensor (cylinder bank 2) in the control unit has a malfunction. There is a signal below the permissible limit value. |
| P064E85 | - | The processor of the oxygen sensor (cylinder bank 2) in the control unit has a malfunction. There is a signal above the permissible limit value. |
| P064E86 | - | The processor of the oxygen sensor (cylinder bank 2) in the control unit has a malfunction. There is an incorrect signal. |
| P065100 | - | Output 2 for the reference voltage of the sensors has an electrical fault or an open circuit. |
| P065104 | - | Output 2 for the reference voltage of the sensors has an electrical fault or an open circuit. There is an internal fault. |
| P065116 | - | Output 2 for the reference voltage of the sensors has an electrical fault or an open circuit. The limit value for electrical voltage has not been attained. |
| P065117 | - | Output 2 for the reference voltage of the sensors has an electrical fault or an open circuit. The limit value for electrical voltage has been exceeded. |
| P065413 | - | The output signal for engine speed has an electrical fault or open circuit. There is an open circuit. |
| P065B00 | - | The alternator has a malfunction. |
| P066000 | - | The actuation for the switchover valve of the intake manifold (cylinder bank 1) has an electrical fault or open circuit. |
| P066100 | - | The actuation for the switchover valve of the intake manifold (cylinder bank 1) has a short circuit to ground. |
| P066200 | - | The actuation for the switchover valve of the intake manifold (cylinder bank 1) has a short circuit to positive. |
| P066300 | - | The actuation for the switchover valve of the intake manifold (cylinder bank 2) has an electrical fault or open circuit. |
| P066400 | - | The actuation for the switchover valve of the intake manifold (cylinder bank 2) has a short circuit to ground. |
| P066500 | - | The actuation for the switchover valve of the intake manifold (cylinder bank 2) has a short circuit to positive. |
| P066700 | - | The internal temperature sensor of the control unit has a malfunction. |
| P066716 | - | The internal temperature sensor of the control unit has a malfunction. The limit value for electrical voltage has not been attained. |
| P066717 | - | The internal temperature sensor of the control unit has a malfunction. The limit value for electrical voltage has been exceeded. |
| P066729 | - | The internal temperature sensor of the control unit has a malfunction. There is an invalid signal. |
| P069100 | - | The output of electric fan 1 has a short circuit to ground. |
| P069116 | - | This error code can be ignored and erased. |
| P069200 | - | The output of electric fan 1 has a short circuit to positive. |
| P069212 | - | This error code can be ignored and erased. |
| P069704 | - | Output 3 for the reference voltage of the sensors has an electrical fault or an open circuit. There is an internal fault. |
| P06AF00 | - | The torque control system has triggered torque limitation or shutoff of the combustion engine. |
| P06DA00 | - | The actuation of the valve of the oil pump in the combustion engine has an electrical fault or open circuit. |
| P06DB00 | - | The actuation of the valve of the oil pump in the combustion engine has a short circuit to ground. |
| P06DC00 | - | The actuation of the valve of the oil pump in the combustion engine has a short circuit to positive. |
| P06ED11 | - | The output signal for engine speed has a short circuit to ground. There is a short circuit to ground. |
| P06EE12 | - | The output signal for engine speed has a short circuit to positive. There is a short circuit to positive. |
| P070200 | - | Control unit 'Transmission' has a malfunction. |
| P070229 | - | Control unit 'Transmission' has a malfunction. There is an invalid signal. |
| P070400 | - | Switch 'Clutch pedal' has an electrical fault. |
| P070500 | - | Selection range sensor A has an electrical fault. |
| P070600 | - | Selection range sensor A has a malfunction. |
| P071500 | - | Rpm sensor 'Turbine wheel' has an electrical fault. |
| P071600 | - | Rpm sensor 'Turbine wheel' has a malfunction. |
| P071700 | - | The signal of rpm sensor 'Turbine wheel' is missing. |
| P071800 | - | Rpm sensor 'Turbine wheel' has a sporadic malfunction. |
| P072000 | - | Rpm sensor 'Output shaft' has an electrical fault. |
| P072200 | - | The signal of rpm sensor 'Output shaft' is missing. |
| P072300 | - | Rpm sensor 'Output shaft' has a sporadic malfunction. |
| P073000 | - | There is an impermissible transmission ratio. |
| P074000 | - | Standard-Fehlercode |
| P074300 | - | Standard-Fehlercode |
| P074800 | - | Pressure regulating valve 1 has an electrical fault. |
| P075300 | - | Standard-Fehlercode |
| P075800 | - | Standard-Fehlercode |
| P076300 | - | Standard-Fehlercode |
| P077800 | - | Pressure regulating valve 2 has an electrical fault. |
| P079800 | - | Pressure regulating valve 3 has an electrical fault. |
| P082011 | - | 'Transmission neutral' sensor has an electrical fault. There is a short circuit to ground. |
| P082015 | - | 'Transmission neutral' sensor has an electrical fault. There is a short circuit to positive or an open circuit. |
| P082064 | - | 'Transmission neutral' sensor has an electrical fault. There is an implausible signal. |
| P082096 | - | 'Transmission neutral' sensor has an electrical fault. There is an internal component fault. |
| P082A00 | - | Gear Lever X Position Sensor 1 Circuit Range/Performance no sub type information |
| P082B00 | - | Gear Lever X Position Sensor 1 Circuit Low no sub type information |
| P082C00 | - | Gear Lever X Position Sensor 1 Circuit High no sub type information |
| P083600 | - | Four Wheel Drive (4WD) Switch Circuit no sub type information |
| P086B00 | - | Neutral Position Sensor 'A' Range/Performance no sub type information |
| P099900 | - | This error code can be ignored and erased. |
| P0A0800 | - | DC/DC Converter Status Circuit no sub type information |
| P0A0B00 | - | The interlock circuit of the high-voltage on-board electrical system has a malfunction. |
| P0A0F05 | - | This error code can be ignored and erased. |
| P0A0F97 | - | The engine does not start. The system function is restricted. |
| P0A1200 | - | DC/DC Converter Enable Circuit Low no sub type information |
| P0A1300 | - | DC/DC Converter Enable Circuit High no sub type information |
| P0A1400 | - | The actuation for engine mount 'A' has an electrical fault or open circuit. |
| P0A1500 | - | The actuation for engine mount 'A' has a short circuit to ground. |
| P0A1600 | - | The actuation for engine mount 'A' has a short circuit to positive. |
| P0A1E01 | - | Control unit 'Integrated starter alternator' has a malfunction. There is a general electrical fault. |
| P0A1E02 | - | Control unit 'Integrated starter alternator' has a malfunction. There is a general signal fault. |
| P0A1E03 | - | Control unit 'Integrated starter alternator' has a malfunction. There is a frequency or pulse width modulation fault. |
| P0A1E04 | - | Control unit 'Integrated starter alternator' has a malfunction. There is an internal fault. |
| P0A1E05 | - | Control unit 'Integrated starter alternator' has a malfunction. There is a programming fault. |
| P0A1E06 | - | Control unit 'Integrated starter alternator' has a malfunction. There is an algorithm fault. |
| P0A1E07 | - | Control unit 'Integrated starter alternator' has a malfunction. There is a mechanical fault. |
| P0A1E08 | - | Control unit 'Integrated starter alternator' has a malfunction. There is a signal fault or the message is faulty. |
| P0A1E09 | - | Control unit 'Integrated starter alternator' has a malfunction. There is a component fault. |
| P0A1E10 | - | Control unit 'Integrated starter alternator' has a malfunction. Reserved for ISO/SAE |
| P0A1E11 | - | Control unit 'Integrated starter alternator' has a malfunction. There is a short circuit to ground. |
| P0A1E12 | - | Control unit 'Integrated starter alternator' has a malfunction. There is a short circuit to positive. |
| P0A1E13 | - | Control unit 'Integrated starter alternator' has a malfunction. There is an open circuit. |
| P0A1E14 | - | Control unit 'Integrated starter alternator' has a malfunction. There is a short circuit to ground or an open circuit. |
| P0A1E15 | - | Control unit 'Integrated starter alternator' has a malfunction. There is a short circuit to positive or an open circuit. |
| P0A1E16 | - | Control unit 'Integrated starter alternator' has a malfunction. The limit value for electrical voltage has not been attained. |
| P0A1E17 | - | Control unit 'Integrated starter alternator' has a malfunction. The limit value for electrical voltage has been exceeded. |
| P0A7D18 | - | The charge level of the high-voltage battery module is low. The limit value for current has not been attained. |
| P0A7D1F | - | The charge level of the high-voltage battery module is low. There is a sporadic fault. |
| P0A9400 | - | Control unit 'DC/DC converter' has a malfunction. |
| P0A9408 | - | Control unit 'DC/DC converter' has a malfunction. There is a signal fault or the message is faulty. |
| P0A9429 | - | Control unit 'DC/DC converter' has a malfunction. There is an invalid signal. |
| P0AB900 | - | The hybrid system has a malfunction. |
| P0AB901 | - | The hybrid system has a malfunction. There is a general electrical fault. |
| P0AB902 | - | This error code can be ignored and erased. |
| P0AB903 | - | This error code can be ignored and erased. |
| P0AB904 | - | This error code can be ignored and erased. |
| P0AB905 | - | This error code can be ignored and erased. |
| P0AB906 | - | This error code can be ignored and erased. |
| P0AB908 | - | This error code can be ignored and erased. |
| P0AB919 | - | This error code can be ignored and erased. |
| P0AB91A | - | This error code can be ignored and erased. |
| P0AB91B | - | This error code can be ignored and erased. |
| P0AB91D | - | This error code can be ignored and erased. |
| P0AB91E | - | This error code can be ignored and erased. |
| P0AB921 | - | This error code can be ignored and erased. |
| P0AB922 | - | This error code can be ignored and erased. |
| P0AB925 | - | This error code can be ignored and erased. |
| P0AB929 | - | This error code can be ignored and erased. |
| P0AB92F | - | This error code can be ignored and erased. |
| P0AB932 | - | This error code can be ignored and erased. |
| P0AB933 | - | This error code can be ignored and erased. |
| P0AB934 | - | This error code can be ignored and erased. |
| P0AB935 | - | This error code can be ignored and erased. |
| P0AB936 | - | This error code can be ignored and erased. |
| P0AB937 | - | This error code can be ignored and erased. |
| P0AB938 | - | This error code can be ignored and erased. |
| P0AB939 | - | This error code can be ignored and erased. |
| P0AB93A | - | This error code can be ignored and erased. |
| P0AB953 | - | This error code can be ignored and erased. |
| P0AB956 | - | This error code can be ignored and erased. |
| P0AB961 | - | This error code can be ignored and erased. |
| P0AB964 | - | This error code can be ignored and erased. |
| P0AB965 | - | This error code can be ignored and erased. |
| P0AB966 | - | This error code can be ignored and erased. |
| P0AB967 | - | This error code can be ignored and erased. |
| P0AB968 | - | This error code can be ignored and erased. |
| P0AB981 | - | This error code can be ignored and erased. |
| P0AB984 | - | This error code can be ignored and erased. |
| P0AB986 | - | This error code can be ignored and erased. |
| P0AB98F | - | This error code can be ignored and erased. |
| P0AB992 | - | This error code can be ignored and erased. |
| P0AB993 | - | This error code can be ignored and erased. |
| P0AB994 | - | This error code can be ignored and erased. |
| P0AB99A | - | This error code can be ignored and erased. |
| P0C2F00 | - | There is an internal control unit fault in the monitoring function of signal 'Engine speed'. |
| P0C7600 | - | The discharge time in the high-voltage on-board electrical system is too long. |
| P101300 | - | Reserved JM 9/9/07 no sub type information |
| P101301 | - | Reserved JM 9/9/07 General Electrical Failure |
| P101302 | - | Reserved JM 9/9/07 General Signal Failure |
| P101303 | - | Reserved JM 9/9/07 FM (Frequency Modulated) / PWM (Pulse Width Modulated) Failures |
| P101304 | - | Reserved JM 9/9/07 System Internal Failures |
| P101305 | - | Reserved JM 9/9/07 System Programming Failures |
| P101306 | - | Reserved JM 9/9/07 Algorithm Based Failures |
| P101307 | - | Reserved JM 9/9/07 Mechanical Failures |
| P101308 | - | Reserved JM 9/9/07 Bus Signal / Message Failures |
| P101309 | - | Reserved JM 9/9/07 Component Failures |
| P101310 | - | Reserved JM 9/9/07 ISO/SAE reserved |
| P101311 | - | Reserved JM 9/9/07 circuit short to ground |
| P101312 | - | Reserved JM 9/9/07 circuit short to battery |
| P101313 | - | Reserved JM 9/9/07 circuit open |
| P101314 | - | Reserved JM 9/9/07 circuit short to ground or open |
| P101315 | - | Reserved JM 9/9/07 circuit short to battery or open |
| P101316 | - | Reserved JM 9/9/07 circuit voltage below threshold |
| P101317 | - | Reserved JM 9/9/07 circuit voltage above threshold |
| P101318 | - | Reserved JM 9/9/07 circuit current below threshold |
| P101319 | - | Reserved JM 9/9/07 circuit current above threshold |
| P10131A | - | Reserved JM 9/9/07 circuit resistance below threshold |
| P10131B | - | Reserved JM 9/9/07 circuit resistance above threshold |
| P10131C | - | Reserved JM 9/9/07 circuit voltage out of range |
| P10131D | - | Reserved JM 9/9/07 circuit current out of range |
| P10131E | - | Reserved JM 9/9/07 circuit resistance out of range |
| P10131F | - | Reserved JM 9/9/07 circuit intermittent |
| P101320 | - | Reserved JM 9/9/07 ISO/SAE reserved |
| P101321 | - | Reserved JM 9/9/07 signal amplitude < minimum |
| P101322 | - | Reserved JM 9/9/07 signal amplitude > maximum |
| P101323 | - | Reserved JM 9/9/07 signal stuck low |
| P101324 | - | Reserved JM 9/9/07 signal stuck high |
| P101325 | - | Reserved JM 9/9/07 signal shape / waveform failure |
| P101326 | - | Reserved JM 9/9/07 signal rate of change below threshold |
| P101327 | - | Reserved JM 9/9/07 signal rate of change above threshold |
| P101328 | - | Reserved JM 9/9/07 signal bias level out of range / zero adjustment failure |
| P101329 | - | Reserved JM 9/9/07 signal invalid |
| P10132A | - | Reserved JM 9/9/07 signal stuck in range |
| P10132B | - | Reserved JM 9/9/07 Signal Cross Coupled |
| P10132F | - | Reserved JM 9/9/07 signal erratic |
| P101330 | - | Reserved JM 9/9/07 ISO/SAE reserved |
| P101331 | - | Reserved JM 9/9/07 no signal |
| P101332 | - | Reserved JM 9/9/07 signal low time < minimum |
| P126F01 | - | This error code can be ignored and erased. |
| P13A600 | - | This error code can be ignored and erased. |
| P13A604 | - | Emergency shutoff input has a malfunction. There is an internal fault. |
| P13A800 | - | The efficiency of the NOx storage catalytic converter (cylinder bank 2) is insufficient: stratified operation disabled. |
| P13A964 | - | The efficiency of the NOx storage catalytic converter (cylinder bank 2) is insufficient: sulfurous fuel suspected. There is an implausible signal. |
| P13AA00 | - | The efficiency of the NOx storage catalytic converter (cylinder bank 1) is insufficient: stratified operation disabled. |
| P13AA07 | - | The efficiency of the NOx storage catalytic converter (cylinder bank 1) is insufficient: stratified operation disabled. There is a mechanical fault. |
| P13AA09 | - | The efficiency of the NOx storage catalytic converter (cylinder bank 1) is insufficient: stratified operation disabled. There is a component fault. |
| P13AB64 | - | The efficiency of the NOx storage catalytic converter (cylinder bank 1) is insufficient: sulfurous fuel suspected. There is an implausible signal. |
| P13AC12 | - | The output for emergency shutoff of control unit 'Power electronics' has a short circuit to positive. There is a short circuit to positive. |
| P13AD11 | - | The output for emergency shutoff of control unit 'Power electronics' has a short circuit to ground. There is a short circuit to ground. |
| P13AE13 | - | The output for emergency shutoff of control unit 'Power electronics' has an open circuit. There is an open circuit. |
| P13AF12 | - | The output for on-board electrical system shutoff has a short circuit to positive. There is a short circuit to positive. |
| P13B011 | - | The output for on-board electrical system shutoff has a short circuit to ground. There is a short circuit to ground. |
| P13B113 | - | The output for on-board electrical system switchover has an electrical fault or an open circuit. There is an open circuit. |
| P13B200 | - | Electrical fuse 1 for the ignition coil has a malfunction. |
| P13B300 | - | Electrical fuse 2 for the ignition coil has a malfunction. |
| P13C200 | - | The exhaust flap has a malfunction. |
| P13C271 | - | The exhaust flap has a malfunction. The actuator is blocked. |
| P13C272 | - | The exhaust flap has a malfunction. The actuator does not close. |
| P13C273 | - | The exhaust flap has a malfunction. The actuator does not open. |
| P13C298 | - | The exhaust flap has a malfunction. The component or the system has overtemperature. |
| P13C311 | - | The output for the 'high/low-temperature circuit' bypass flap's switchover valve has a malfunction. There is a short circuit to ground. |
| P13C312 | - | The output for the 'high/low-temperature circuit' bypass flap's switchover valve has a malfunction. There is a short circuit to positive. |
| P13C313 | - | The output for the 'high/low-temperature circuit' bypass flap's switchover valve has a malfunction. There is an open circuit. |
| P13C523 | - | A short-term torque limitation was detected by the knock control. No signal change: Voltage level is too low. |
| P13C624 | - | A long-term torque limitation was detected by the knock control. No signal change: Voltage level is too high. |
| P13C700 | - | The exhaust flap has an electrical fault or an open circuit. |
| P13C800 | - | The exhaust flap has a short circuit to positive. |
| P13C900 | - | The exhaust flap has a short circuit to ground. |
| P13EA00 | - | The ignition angle setting has a malfunction during cold starting (partial load operation). |
| P13FE07 | - | HDCAC_HV_Dischargemax: Intermediate Voltage System Performance Intermediate Voltage System Performance General Signal Failure |
| P140400 | - | Exhaust flap 2 has a malfunction. |
| P140471 | - | Exhaust flap 2 has a malfunction. The actuator is blocked. |
| P140472 | - | Exhaust flap 2 has a malfunction. The actuator does not close. |
| P140473 | - | Exhaust flap 2 has a malfunction. The actuator does not open. |
| P140498 | - | Exhaust flap 2 has a malfunction. The component or the system has overtemperature. |
| P141100 | - | Exhaust flap 2 has an electrical fault or an open circuit. |
| P141200 | - | Exhaust flap 2 has a short circuit to positive. |
| P141300 | - | Exhaust flap 2 has a short circuit to ground. |
| P150F00 | - | This error code can be ignored and erased. |
| P161404 | - | This error code can be ignored and erased. |
| P161405 | - | This error code can be ignored and erased. |
| P161406 | - | This error code can be ignored and erased. |
| P164400 | - | An incorrect variant coding or configuration was detected. |
| P164404 | - | An incorrect variant coding or configuration was detected. There is an internal fault. |
| P164408 | - | An incorrect variant coding or configuration was detected. There is a signal fault or the message is faulty. |
| P164429 | - | An incorrect variant coding or configuration was detected. There is an invalid signal. |
| P16442A | - | An incorrect variant coding or configuration was detected. There is no signal change. |
| P164456 | - | An incorrect variant coding or configuration was detected. An incorrect or incompatible configuration was detected. |
| P164464 | - | An incorrect variant coding or configuration was detected. There is an implausible signal. |
| P167085 | - | Calibration of the torque curve of the control unit has a malfunction. There is a signal above the permissible limit value. |
| P167B09 | - | The drivetrain has been switched off due to a crash signal. There is a component fault. |
| P199900 | - | This error code can be ignored and erased. |
| P1A8802 | - | This error code can be ignored and erased. |
| P1CC813 | - | The quantity control valve (cylinder bank 2) has an electrical fault or an open circuit. There is an open circuit. |
| P1CCA11 | - | The quantity control valve (cylinder bank 2) has a short circuit to ground. There is a short circuit to ground. |
| P1CCB12 | - | The quantity control valve (cylinder bank 2) has a short circuit to positive. There is a short circuit to positive. |
| P1CCF00 | - | High pressure could not be built up during engine start. |
| P1CD009 | - | The NOx storage catalytic converter (cylinder bank 1) has been removed. There is a component fault. |
| P1CD109 | - | The NOx storage catalytic converter (cylinder bank 2) has been removed. There is a component fault. |
| P1CD212 | - | The output for circulation pump 'Transmission oil cooling' has a short circuit to positive. There is a short circuit to positive. |
| P1CD311 | - | The output for circulation pump 'Transmission oil cooling' has a short circuit to ground. There is a short circuit to ground. |
| P1CD400 | - | The output for circulation pump 'Transmission oil cooling' has an electrical fault or an open circuit. |
| P1CD509 | - | The output for shutoff valve 'Transmission oil cooling' has a short circuit to positive. There is a component fault. |
| P1CD609 | - | The output for shutoff valve 'Transmission oil cooling' has a short circuit to ground. There is a component fault. |
| P1CD709 | - | The output for shutoff valve 'Transmission oil cooling' has an electrical fault or an open circuit. There is a component fault. |
| P1CD878 | - | A leakage in the exhaust pipe upstream of the right NOx sensor was detected. The adaptation or adjustment is incorrect. |
| P1CD87A | - | A leakage in the exhaust pipe upstream of the right NOx sensor was detected. Leakage or a defective seal was detected. |
| P1CD978 | - | A leakage in the exhaust pipe upstream of the left NOx sensor was detected. The adaptation or adjustment is incorrect. |
| P1CD97A | - | A leakage in the exhaust pipe upstream of the left NOx sensor was detected. Leakage or a defective seal was detected. |
| P1CDE00 | - | The ECO start/stop function has detected excessively low engine speed during the starting procedure. |
| P1CDF00 | - | The ECO start/stop function has aborted an engine start due to a fault in sensor 'Neutral position of transmission' or at switch 'Clutch pedal'. |
| P1CE000 | - | This error code can be ignored and erased. |
| P1CE100 | - | The ECO start/stop function has detected implausible drive authorization data. |
| P1CE200 | - | The ECO start/stop function has detected excessively low engine speed. |
| P1CE365 | - | No result obtained from AFIM-diagnosis. The signal has too few transitions or events. |
| P1CE49A | - | Implausible result obtained from AFIM-Diagnosis. The operating conditions for the component or the system are not fulfilled. |
| P1CE577 | - | Recognization of maximum Lambda failure at cylinder equalization (failure stage 2) The commanded position cannot be reached. |
| P1CE678 | - | Recognization of minimum Lambda failure at cylinder equalization (failure stage 2) The adaptation or adjustment is incorrect. |
| P1CE700 | - | Crankcase ventilation in wide open throttle operation (cylinder bank 1) has a malfunction. |
| P1CE800 | - | Crankcase ventilation in wide open throttle operation (cylinder bank 2) has a malfunction. |
| P1CEF85 | - | Recognization of maximum fuel failure at cylinder equalization (failure stage 1) There is a signal above the permissible limit value. |
| P1CF084 | - | Recognization of minimum fuel failure at cylinder equalization (failure stage 1) There is a signal below the permissible limit value. |
| P1CF129 | - | signal invalid |
| P1CF186 | - | Implausible result of cylinder equalization obtained. There is an invalid signal. |
| P1CF200 | - | No result of cylinder equalization obtained. |
| P1CF385 | - | Recognization of maximum fuel failure at cylinder equalization in shift operation (failure stage 1) There is a signal above the permissible limit value. |
| P1CF484 | - | Recognization of minimum fuel failure at cylinder equalization in shift operation (failure stage 1) There is a signal below the permissible limit value. |
| P1D0400 | - | The ECO start/stop function has requested a manual engine start. |
| P1D0500 | - | The ECO start/stop function has prevented an engine stop. |
| P1D0600 | - | This error code can be ignored and erased. |
| P1D0602 | - | The ECO start/stop function has a malfunction. There is a general signal fault. |
| P1D0700 | - | The ECO start/stop function has prevented an engine start. |
| P1D2909 | - | An internal leakage in the high pressure fuel pump was detected. There is a component fault. |
| P1D2A09 | - | At least one defective seal pack was detected. There is a component fault. |
| P1D4212 | - | The output for the switchover valve of the bypass flap 'High/low-temperature circuit' has a short circuit to positive. There is a short circuit to positive. |
| P1D4311 | - | The output for the switchover valve of the bypass flap 'High/low-temperature circuit' has a short circuit to ground. There is a short circuit to ground. |
| P1D4413 | - | The output for the switchover valve of the bypass flap 'High/low-temperature circuit' has an electrical fault or an open circuit. There is an open circuit. |
| P1D6D00 | - | The ECO start/stop function has detected an impermissible engine stop. |
| P20658F | - | The right fuel level sensor has an electrical fault. The signal or message is erratic. |
| P206600 | - | The right fuel level sensor has a malfunction. |
| P20662A | - | The right fuel level sensor has a malfunction. There is no signal change. |
| P206685 | - | The right fuel level sensor has a malfunction. There is a signal above the permissible limit value. |
| P206711 | - | The right fuel level sensor has a short circuit to ground. There is a short circuit to ground. |
| P206812 | - | The right fuel level sensor has a short circuit to positive. There is a short circuit to positive. |
| P207204 | - | The throttle valve is blocked due to ice. There is an internal fault. |
| P207284 | - | The throttle valve is blocked due to ice. There is a signal below the permissible limit value. |
| P207285 | - | The throttle valve is blocked due to ice. There is a signal above the permissible limit value. |
| P207286 | - | The throttle valve is blocked due to ice. There is an incorrect signal. |
| P208800 | - | Actuator 'Intake camshaft' (cylinder bank 1) has a short circuit to ground. |
| P208900 | - | Actuator 'Intake camshaft' (cylinder bank 1) has a short circuit to positive. |
| P209000 | - | Actuator 'Exhaust camshaft' (cylinder bank 1) has a short circuit to ground. |
| P209100 | - | Actuator 'Exhaust camshaft' (cylinder bank 1) has a short circuit to positive. |
| P209200 | - | Actuator 'Intake camshaft' (cylinder bank 2) has a short circuit to ground. |
| P209300 | - | Actuator 'Intake camshaft' (cylinder bank 2) has a short circuit to positive. |
| P209400 | - | Actuator 'Exhaust camshaft' (cylinder bank 2) has a short circuit to ground. |
| P209500 | - | Actuator 'Exhaust camshaft' (cylinder bank 2) has a short circuit to positive. |
| P209600 | - | The mixture is too lean downstream of the catalytic converter (cylinder bank 1). |
| P209700 | - | The mixture is too rich downstream of the catalytic converter (cylinder bank 1). |
| P209800 | - | The mixture is too lean downstream of the catalytic converter (cylinder bank 2). |
| P209900 | - | The mixture is too rich downstream of the catalytic converter (cylinder bank 2). |
| P20B100 | - | Output for coolant shutoff valve has an electrical fault or open circuit. |
| P20B300 | - | Output for coolant shutoff valve has a short circuit to ground. |
| P20B400 | - | Output for coolant shutoff valve has a short circuit to positive. |
| P210100 | - | The throttle valve actuator has a malfunction. |
| P210128 | - | The throttle valve actuator has a malfunction. The signal offset is outside the permissible range. |
| P210129 | - | The throttle valve actuator has a malfunction. There is an invalid signal. |
| P210164 | - | The throttle valve actuator has a malfunction. There is an implausible signal. |
| P210184 | - | The throttle valve actuator has a malfunction. There is a signal below the permissible limit value. |
| P210185 | - | The throttle valve actuator has a malfunction. There is a signal above the permissible limit value. |
| P210200 | - | The throttle valve actuator has a short circuit to ground. |
| P210300 | - | The throttle valve actuator has a short circuit to positive. |
| P211100 | - | The throttle valve is jammed open. |
| P211900 | - | This error code can be ignored and erased. |
| P212200 | - | Position sensor 1 for the accelerator pedal has a short circuit to ground. |
| P212300 | - | Position sensor 1 for the accelerator pedal has a short circuit to positive |
| P212711 | - | Position sensor 2 for the accelerator pedal has a short circuit to ground. There is a short circuit to ground. |
| P212812 | - | Position sensor 2 for the accelerator pedal has a short circuit to positive There is a short circuit to positive. |
| P213500 | - | The values from the position sensors of the throttle valve are implausible in relation to each other. |
| P213629 | - | The values from position sensors 'A/C' of the throttle valve are implausible relative to each other. There is an invalid signal. |
| P213700 | - | The values from position sensors 'B/C' of the throttle valve are implausible relative to each other. |
| P213800 | - | The values from the position sensors of the accelerator pedal are implausible in relation to each other. |
| P213A08 | - | The output for the exhaust gas recirculation actuator (cylinder bank 2) has an electrical fault or open circuit. There is a signal fault or the message is faulty. |
| P217609 | - | This error code can be ignored and erased. |
| P217616 | - | Adaptation of the idle position of the throttle valve actuator was not performed. The limit value for electrical voltage has not been attained. |
| P217617 | - | Adaptation of the idle position of the throttle valve actuator was not performed. The limit value for electrical voltage has been exceeded. |
| P217700 | - | The mixture (cylinder bank 1) is too lean in partial load operation. |
| P217797 | - | The mixture (cylinder bank 1) is too lean in partial load operation. The system function is restricted. |
| P217800 | - | The mixture (cylinder bank 1) is too rich in partial load operation. |
| P217897 | - | The mixture (cylinder bank 1) is too rich in partial load operation. The system function is restricted. |
| P217900 | - | The mixture (cylinder bank 2) is too lean in partial load operation. |
| P217997 | - | The mixture (cylinder bank 2) is too lean in partial load operation. The system function is restricted. |
| P218000 | - | The mixture (cylinder bank 2) is too rich in partial load operation. |
| P218097 | - | The mixture (cylinder bank 2) is too rich in partial load operation. The system function is restricted. |
| P218762 | - | The mixture (cylinder bank 1) is too lean at idle speed. The signal comparison is faulty. |
| P218797 | - | The mixture (cylinder bank 1) is too lean at idle speed. The system function is restricted. |
| P218862 | - | The mixture (cylinder bank 1) is too rich at idle speed. The signal comparison is faulty. |
| P218897 | - | The mixture (cylinder bank 1) is too rich at idle speed. The system function is restricted. |
| P218962 | - | The mixture (cylinder bank 2) at idle is too lean. The signal comparison is faulty. |
| P218997 | - | The mixture (cylinder bank 2) at idle is too lean. The system function is restricted. |
| P219062 | - | The mixture (cylinder bank 2) at idle is too rich. The signal comparison is faulty. |
| P219097 | - | The mixture (cylinder bank 2) at idle is too rich. The system function is restricted. |
| P219500 | - | This error code can be ignored and erased. |
| P219585 | - | The signal from oxygen sensor 1 (cylinder bank 1) is shifted towards 'Lean'. There is a signal above the permissible limit value. |
| P219600 | - | This error code can be ignored and erased. |
| P219684 | - | The signal from oxygen sensor 1 (cylinder bank 1) is shifted towards 'Rich'. There is a signal below the permissible limit value. |
| P219700 | - | This error code can be ignored and erased. |
| P219785 | - | The signal from oxygen sensor 1 (cylinder bank 2) is shifted towards 'Lean'. There is a signal above the permissible limit value. |
| P219800 | - | This error code can be ignored and erased. |
| P219884 | - | The signal from oxygen sensor 1 (cylinder bank 2) is shifted towards 'Rich'. There is a signal below the permissible limit value. |
| P219C29 | - | Mixture formation (cylinder 1) is irregular. There is an invalid signal. |
| P219C77 | - | Mixture formation (cylinder 1) is irregular. The commanded position cannot be reached. |
| P219C78 | - | Mixture formation (cylinder 1) is irregular. The adaptation or adjustment is incorrect. |
| P219D29 | - | Mixture formation (cylinder 2) is irregular. There is an invalid signal. |
| P219D77 | - | Mixture formation (cylinder 2) is irregular. The commanded position cannot be reached. |
| P219D78 | - | Mixture formation (cylinder 2) is irregular. The adaptation or adjustment is incorrect. |
| P219E29 | - | Mixture formation (cylinder 3) is irregular. There is an invalid signal. |
| P219E77 | - | Mixture formation (cylinder 3) is irregular. The commanded position cannot be reached. |
| P219E78 | - | Mixture formation (cylinder 3) is irregular. The adaptation or adjustment is incorrect. |
| P219F29 | - | Mixture formation (cylinder 4) is irregular. There is an invalid signal. |
| P219F77 | - | Mixture formation (cylinder 4) is irregular. The commanded position cannot be reached. |
| P219F78 | - | Mixture formation (cylinder 4) is irregular. The adaptation or adjustment is incorrect. |
| P21A029 | - | Mixture formation (cylinder 5) is irregular. There is an invalid signal. |
| P21A077 | - | Mixture formation (cylinder 5) is irregular. The commanded position cannot be reached. |
| P21A078 | - | Mixture formation (cylinder 5) is irregular. The adaptation or adjustment is incorrect. |
| P21A129 | - | Mixture formation (cylinder 6) is irregular. There is an invalid signal. |
| P21A177 | - | Mixture formation (cylinder 6) is irregular. The commanded position cannot be reached. |
| P21A178 | - | Mixture formation (cylinder 6) is irregular. The adaptation or adjustment is incorrect. |
| P21A277 | - | Mixture formation (cylinder 7) is irregular. The commanded position cannot be reached. |
| P21A278 | - | Mixture formation (cylinder 7) is irregular. The adaptation or adjustment is incorrect. |
| P21A377 | - | Mixture formation (cylinder 8) is irregular. The commanded position cannot be reached. |
| P21A378 | - | Mixture formation (cylinder 8) is irregular. The adaptation or adjustment is incorrect. |
| P220087 | - | This error code can be ignored and erased. |
| P220100 | - | The NOx sensor (cylinder bank 1) has a malfunction. |
| P220101 | - | The NOx sensor (cylinder bank 1) has a malfunction. There is a general electrical fault. |
| P220108 | - | The NOx sensor (cylinder bank 1) has a malfunction. There is a signal fault or the message is faulty. |
| P220164 | - | The NOx sensor (cylinder bank 1) has a malfunction. There is an implausible signal. |
| P220165 | - | The NOx sensor (cylinder bank 1) has a malfunction. The signal has too few transitions or events. |
| P220513 | - | The heater of the NOx sensor (cylinder bank 1) has an electrical fault or an open circuit. There is an open circuit. |
| P220516 | - | The heater of the NOx sensor (cylinder bank 1) has an electrical fault or an open circuit. The limit value for electrical voltage has not been attained. |
| P221387 | - | This error code can be ignored and erased. |
| P221400 | - | The NOx sensor (cylinder bank 2) has a malfunction. |
| P221401 | - | The NOx sensor (cylinder bank 2) has a malfunction. There is a general electrical fault. |
| P221408 | - | The NOx sensor (cylinder bank 2) has a malfunction. There is a signal fault or the message is faulty. |
| P221464 | - | The NOx sensor (cylinder bank 2) has a malfunction. There is an implausible signal. |
| P221465 | - | The NOx sensor (cylinder bank 2) has a malfunction. The signal has too few transitions or events. |
| P221813 | - | The heater of the NOx sensor (cylinder bank 2) has an electrical fault or an open circuit. There is an open circuit. |
| P221816 | - | The heater of the NOx sensor (cylinder bank 2) has an electrical fault or an open circuit. The limit value for electrical voltage has not been attained. |
| P222700 | - | The ambient pressure sensor has a malfunction. |
| P222784 | - | The ambient pressure sensor has a malfunction. There is a signal below the permissible limit value. |
| P222785 | - | The ambient pressure sensor has a malfunction. There is a signal above the permissible limit value. |
| P222786 | - | The ambient pressure sensor has a malfunction. There is an incorrect signal. |
| P222800 | - | The ambient pressure sensor has a short circuit to ground. |
| P222900 | - | The ambient pressure sensor has a short circuit to positive. |
| P222B27 | - | Pressure sensor 2 has a malfunction. The signal change rate is above the permissible limit value. |
| P222B28 | - | Pressure sensor 2 has a malfunction. The signal offset is outside the permissible range. |
| P222B64 | - | Pressure sensor 2 has a malfunction. There is an implausible signal. |
| P222B84 | - | Pressure sensor 2 has a malfunction. There is a signal below the permissible limit value. |
| P222C11 | - | Pressure sensor 2 has a short circuit to ground. There is a short circuit to ground. |
| P222D12 | - | Pressure sensor 2 has a short circuit to positive. There is a short circuit to positive. |
| P223100 | - | This error code can be ignored and erased. |
| P223200 | - | The signal line of oxygen sensor 2 (cylinder bank 1) and the electric heater circuit have a short circuit to each other. |
| P223400 | - | This error code can be ignored and erased. |
| P223500 | - | The signal line of oxygen sensor 2 (cylinder bank 2) and the electric heater circuit have a short circuit to each other. |
| P223784 | - | This error code can be ignored and erased. |
| P223785 | - | The pump current connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. There is a signal above the permissible limit value. |
| P223786 | - | This error code can be ignored and erased. |
| P224084 | - | This error code can be ignored and erased. |
| P224085 | - | The pump current connection of oxygen sensor 1 (cylinder bank 2) has an electrical fault or open circuit. There is a signal above the permissible limit value. |
| P224086 | - | This error code can be ignored and erased. |
| P224300 | - | The reference voltage connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. |
| P224700 | - | The reference voltage connection of oxygen sensor 1 (cylinder bank 2) has an electrical fault or open circuit. |
| P225100 | - | This error code can be ignored and erased. |
| P225400 | - | This error code can be ignored and erased. |
| P226321 | - | The boost pressure deviates from the specified value. The signal amplitude is less than the minimum amplitude. |
| P226322 | - | The boost pressure deviates from the specified value. The signal amplitude is greater than the maximum amplitude. |
| P226394 | - | This error code can be ignored and erased. |
| P227000 | - | The signal from oxygen sensor 2 (cylinder bank 1) is shifted towards 'Lean'. |
| P227026 | - | The signal from oxygen sensor 2 (cylinder bank 1) is shifted towards 'Lean'. The signal change rate is below the permissible limit value. |
| P227100 | - | The signal from oxygen sensor 2 (cylinder bank 1) is shifted towards 'Rich'. |
| P227126 | - | The signal from oxygen sensor 2 (cylinder bank 1) is shifted towards 'Rich'. The signal change rate is below the permissible limit value. |
| P227200 | - | The signal from oxygen sensor 2 (cylinder bank 2) is shifted towards 'Lean'. |
| P227226 | - | The signal from oxygen sensor 2 (cylinder bank 2) is shifted towards 'Lean'. The signal change rate is below the permissible limit value. |
| P227300 | - | The signal from oxygen sensor 2 (cylinder bank 2) is shifted towards 'Rich'. |
| P227326 | - | The signal from oxygen sensor 2 (cylinder bank 2) is shifted towards 'Rich'. The signal change rate is below the permissible limit value. |
| P227400 | - | The signal of NOx sensor 1 (cylinder bank 1) is shifted towards 'Lean'. |
| P227423 | - | The signal of NOx sensor 1 (cylinder bank 1) is shifted towards 'Lean'. No signal change: Voltage level is too low. |
| P227426 | - | The signal of NOx sensor 1 (cylinder bank 1) is shifted towards 'Lean'. The signal change rate is below the permissible limit value. |
| P227500 | - | The signal of NOx sensor 1 (cylinder bank 1) is shifted towards 'Rich'. |
| P227524 | - | The signal of NOx sensor 1 (cylinder bank 1) is shifted towards 'Rich'. No signal change: Voltage level is too high. |
| P227526 | - | The signal of NOx sensor 1 (cylinder bank 1) is shifted towards 'Rich'. The signal change rate is below the permissible limit value. |
| P227600 | - | The signal of NOx sensor 1 (cylinder bank 2) is shifted towards 'Lean'. |
| P227623 | - | The signal of NOx sensor 1 (cylinder bank 2) is shifted towards 'Lean'. No signal change: Voltage level is too low. |
| P227626 | - | The signal of NOx sensor 1 (cylinder bank 2) is shifted towards 'Lean'. The signal change rate is below the permissible limit value. |
| P227700 | - | The signal of NOx sensor 1 (cylinder bank 2) is shifted towards 'Rich'. |
| P227724 | - | The signal of NOx sensor 1 (cylinder bank 2) is shifted towards 'Rich'. No signal change: Voltage level is too high. |
| P227726 | - | The signal of NOx sensor 1 (cylinder bank 2) is shifted towards 'Rich'. The signal change rate is below the permissible limit value. |
| P227900 | - | A leak was detected in the intake air system. |
| P227B27 | - | Pressure sensor 3 has a malfunction. The signal change rate is above the permissible limit value. |
| P227B28 | - | Pressure sensor 3 has a malfunction. The signal offset is outside the permissible range. |
| P227B64 | - | Pressure sensor 3 has a malfunction. There is an implausible signal. |
| P227B84 | - | Pressure sensor 3 has a malfunction. There is a signal below the permissible limit value. |
| P227C11 | - | Pressure sensor 3 has a short circuit to ground. There is a short circuit to ground. |
| P227D12 | - | Pressure sensor 3 has a short circuit to positive. There is a short circuit to positive. |
| P227F97 | - | The air mass flow in the intake air system (cylinder bank 2) has a malfunction. The system function is restricted. |
| P228092 | - | The air mass flow in the intake air system (cylinder bank 1) has a malfunction. The function or the instruction is faulty. |
| P228097 | - | The air mass flow in the intake air system (cylinder bank 1) has a malfunction. The system function is restricted. |
| P229F00 | - | NOx sensor 2 (cylinder bank 1) has a malfunction. |
| P229F08 | - | NOx sensor 2 (cylinder bank 1) has a malfunction. There is a signal fault or the message is faulty. |
| P229F64 | - | NOx sensor 2 (cylinder bank 1) has a malfunction. There is an implausible signal. |
| P229F65 | - | NOx sensor 2 (cylinder bank 1) has a malfunction. The signal has too few transitions or events. |
| P22A313 | - | Standard-Fehlercode There is an open circuit. |
| P22A316 | - | Standard-Fehlercode The limit value for electrical voltage has not been attained. |
| P230000 | - | The actuation of ignition coil 1 has a short circuit to ground. |
| P230100 | - | The actuation of ignition coil 1 has a short circuit to positive. |
| P230300 | - | The actuation of ignition coil 2 has a short circuit to ground. |
| P230400 | - | The actuation of ignition coil 2 has a short circuit to positive. |
| P230600 | - | The actuation of ignition coil 3 has a short circuit to ground. |
| P230700 | - | The actuation of ignition coil 3 has a short circuit to positive. |
| P230900 | - | The actuation of ignition coil 4 has a short circuit to ground. |
| P230A00 | - | no sub type information |
| P230A29 | - | signal invalid |
| P230B00 | - | no sub type information |
| P230B29 | - | signal invalid |
| P230C00 | - | no sub type information |
| P230C29 | - | signal invalid |
| P230D00 | - | no sub type information |
| P230D29 | - | signal invalid |
| P230E00 | - | no sub type information |
| P230E29 | - | signal invalid |
| P230F00 | - | no sub type information |
| P230F29 | - | signal invalid |
| P231000 | - | The actuation of ignition coil 4 has a short circuit to positive. |
| P231200 | - | The actuation of ignition coil 5 has a short circuit to ground. |
| P231300 | - | The actuation of ignition coil 5 has a short circuit to positive. |
| P231500 | - | The actuation of ignition coil 6 has a short circuit to ground. |
| P231600 | - | The actuation of ignition coil 6 has a short circuit to positive. |
| P231800 | - | The actuation of ignition coil 7 has a short circuit to ground. |
| P231900 | - | The actuation of ignition coil 7 has a short circuit to positive. |
| P231A00 | - | This error code can be ignored and erased. |
| P231B00 | - | This error code can be ignored and erased. |
| P232100 | - | The actuation of ignition coil 8 has a short circuit to ground. |
| P232200 | - | The actuation of ignition coil 8 has a short circuit to positive. |
| P233627 | - | The knock limit of cylinder 1 has been exceeded. The signal change rate is above the permissible limit value. |
| P233727 | - | The knock limit of cylinder 2 has been exceeded. The signal change rate is above the permissible limit value. |
| P233827 | - | The knock limit of cylinder 3 has been exceeded. The signal change rate is above the permissible limit value. |
| P233927 | - | The knock limit of cylinder 4 has been exceeded. The signal change rate is above the permissible limit value. |
| P234027 | - | The knock limit of cylinder 5 has been exceeded. The signal change rate is above the permissible limit value. |
| P234127 | - | The knock limit of cylinder 6 has been exceeded. The signal change rate is above the permissible limit value. |
| P234227 | - | The knock limit of cylinder 7 has been exceeded. The signal change rate is above the permissible limit value. |
| P234327 | - | The knock limit of cylinder 8 has been exceeded. The signal change rate is above the permissible limit value. |
| P240000 | - | Actuation of the pump in the diagnostic module of the evaporative emission control system has an open circuit. |
| P240004 | - | This error code can be ignored and erased. |
| P240013 | - | Actuation of the pump in the diagnostic module of the evaporative emission control system has an open circuit. There is an open circuit. |
| P240100 | - | Actuation of the pump in the diagnostic module of the evaporative emission control system has a short circuit to ground. |
| P240104 | - | This error code can be ignored and erased. |
| P240111 | - | Actuation of the pump in the diagnostic module of the evaporative emission control system has a short circuit to ground. There is a short circuit to ground. |
| P240200 | - | Actuation of the pump in the diagnostic module of the evaporative emission control system has a short circuit to positive. |
| P240204 | - | This error code can be ignored and erased. |
| P240212 | - | Actuation of the pump in the diagnostic module of the evaporative emission control system has a short circuit to positive. There is a short circuit to positive. |
| P240400 | - | The pump in the diagnostic module of the evaporative emission control system has a malfunction. |
| P240418 | - | The pump in the diagnostic module of the evaporative emission control system has a malfunction. The limit value for current has not been attained. |
| P240419 | - | The pump in the diagnostic module of the evaporative emission control system has a malfunction. The limit value for current has been exceeded. |
| P24041C | - | The pump in the diagnostic module of the evaporative emission control system has a malfunction. The voltage value is outside the permissible range. |
| P240700 | - | The pump in the diagnostic module of the evaporative emission control system has a sporadic malfunction. |
| P240A00 | - | Actuation of the heater in the diagnostic module of the evaporative emission control system has an open circuit. |
| P240B00 | - | Actuation of the heater in the diagnostic module of the evaporative emission control system has a short circuit to ground. |
| P240C00 | - | Actuation of the heater in the diagnostic module of the evaporative emission control system has a short circuit to positive. |
| P241378 | - | Exhaust gas recirculation has a malfunction. The adaptation or adjustment is incorrect. |
| P241400 | - | The signal from oxygen sensor 1 (cylinder bank 1) is implausible. |
| P241500 | - | The signal from oxygen sensor 1 (cylinder bank 2) is implausible. |
| P241800 | - | This error code can be ignored and erased. |
| P241900 | - | This error code can be ignored and erased. |
| P242000 | - | This error code can be ignored and erased. |
| P242200 | - | The shutoff valve of the activated charcoal canister sticks in the closed position. |
| P242F00 | - | Particulate Filter Restriction - Ash Accumulation Bank 1 no sub type information |
| P245000 | - | This error code can be ignored and erased. |
| P245100 | - | This error code can be ignored and erased. |
| P245900 | - | Particulate Filter Regeneration Frequency Bank 1 no sub type information |
| P24D628 | - | Standard-Fehlercode The signal offset is outside the permissible range. |
| P24D62A | - | Standard-Fehlercode There is no signal change. |
| P24D700 | - | Standard-Fehlercode |
| P24D800 | - | Standard-Fehlercode |
| P24D812 | - | Standard-Fehlercode There is a short circuit to positive. |
| P250500 | - | This error code can be ignored and erased. |
| P250513 | - | The power supply at the input of the control unit 'combustion engine' has a malfunction. There is an open circuit. |
| P250516 | - | This error code can be ignored and erased. |
| P250517 | - | This error code can be ignored and erased. |
| P25051C | - | The power supply at the input of the control unit 'combustion engine' has a malfunction. The voltage value is outside the permissible range. |
| P250B46 | - | The oil level sensor has a malfunction. There is an error in the calibration or parameterization memory. |
| P250B92 | - | The oil level sensor has a malfunction. The function or the instruction is faulty. |
| P250B96 | - | The oil level sensor has a malfunction. There is an internal component fault. |
| P250E2A | - | The oil level sensor has a sporadic malfunction. There is no signal change. |
| P250E46 | - | The oil level sensor has a sporadic malfunction. There is an error in the calibration or parameterization memory. |
| P252B46 | - | This error code can be ignored and erased. |
| P252B92 | - | The oil sensor has a malfunction. The function or the instruction is faulty. |
| P252B94 | - | The oil sensor has a malfunction. There is an unexpected instruction. |
| P253900 | - | The pressure sensor of the low-pressure fuel circuit has a malfunction. |
| P254000 | - | The signal for the pressure sensor of the low-pressure fuel circuit is implausible. |
| P254100 | - | The pressure sensor of the low-pressure fuel circuit has a short circuit to ground. |
| P254101 | - | The pressure sensor of the low-pressure fuel circuit has a short circuit to ground. There is a general electrical fault. |
| P254200 | - | The pressure sensor of the low-pressure fuel circuit has a short circuit to positive. |
| P254201 | - | The pressure sensor of the low-pressure fuel circuit has a short circuit to positive. There is a general electrical fault. |
| P256800 | - | The PremAir sensor has a malfunction. |
| P256804 | - | The PremAir sensor has a malfunction. There is an internal fault. |
| P256809 | - | The PremAir sensor has a malfunction. There is a component fault. |
| P25681C | - | This error code can be ignored and erased. |
| P256885 | - | The PremAir sensor has a malfunction. There is a signal above the permissible limit value. |
| P256900 | - | The PremAir sensor has a short circuit to ground. |
| P257000 | - | The PremAir sensor has a short circuit to positive. |
| P257187 | - | The PremAir sensor has a sporadic malfunction. The message is missing. |
| P257300 | - | Standard-Fehlercode |
| P257D00 | - | Contact switch 1 'Engine hood' has a malfunction. |
| P260F26 | - | This error code can be ignored and erased. |
| P260F27 | - | This error code can be ignored and erased. |
| P261008 | - | The engine off time has an implausible value. There is a signal fault or the message is faulty. |
| P261029 | - | The engine off time has an implausible value. There is an invalid signal. |
| P261082 | - | The engine off time has an implausible value. The instruction counter is not updated. |
| P261084 | - | The engine off time has an implausible value. There is a signal below the permissible limit value. |
| P261085 | - | The engine off time has an implausible value. There is a signal above the permissible limit value. |
| P261713 | - | The signal of the position sensor of the crankshaft has an electrical fault or an open circuit. There is an open circuit. |
| P261A00 | - | Actuation of coolant pump 2 has an open circuit. |
| P261C00 | - | Actuation of coolant pump 2 has a short circuit to ground. |
| P261D00 | - | Actuation of coolant pump 2 has a short circuit to positive. |
| P262600 | - | The trimming resistor connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. |
| P262900 | - | The trimming resistor connection of oxygen sensor 1 (cylinder bank 2) has an electrical fault or open circuit. |
| P26A500 | - | Engine Coolant Bypass Valve 'A' Position Sensor Circuit Range/Performance no sub type information |
| P26A600 | - | Engine Coolant Bypass Valve 'A' Position Sensor Circuit Low no sub type information |
| P26A700 | - | Engine Coolant Bypass Valve 'A' Position Sensor Circuit High no sub type information |
| P271600 | - | Pressure regulating valve 4 has an electrical fault. |
| P272500 | - | Pressure regulating valve 5 has an electrical fault. |
| P273400 | - | Pressure regulating valve 6 has an electrical fault. |
| P275700 | - | The pressure regulating valve of the torque converter lockup clutch has a malfunction. |
| P275900 | - | The pressure regulating valve of the torque converter lockup clutch has an electrical fault. |
| P276600 | - | Rpm sensor 2 'Turbine wheel' has a malfunction. |
| P276700 | - | The signal of rpm sensor 2 'Turbine wheel' is missing. |
| P276800 | - | Rpm sensor 2 'Turbine wheel' has a sporadic malfunction. |
| P278700 | - | Clutch temperature too high. |
| P281000 | - | Pressure regulating valve 7 has an electrical fault. |
| U000900 | - | This error code can be ignored and erased. |
| U002886 | - | Communication with the drivetrain CAN bus has a malfunction. There is an incorrect signal. |
| U002888 | - | Communication with the drivetrain CAN bus has a malfunction. Bus OFF |
| U003788 | - | Communication with the chassis CAN bus has a malfunction. Bus OFF |
| U004688 | - | Communication with the drive train sensor CAN bus has a malfunction. Bus OFF |
| U005588 | - | Communication with the hybrid CAN bus has a malfunction. Bus OFF |
| U007304 | - | Drive train CAN bus OFF fault There is an internal fault. |
| U007305 | - | Drive train CAN bus OFF fault There is a programming fault. |
| U010187 | - | Communication with control unit 'Transmission' has a malfunction. The message is missing. |
| U010287 | - | Communication with the transfer case has a malfunction. The message is missing. |
| U010300 | - | Communication with the electronic selector lever module has a malfunction. |
| U010387 | - | Communication with the electronic selector lever module has a malfunction. The message is missing. |
| U010987 | - | Communication with control unit 'Fuel pump' has a malfunction. The message is missing. |
| U011087 | - | This error code can be ignored and erased. |
| U011187 | - | Communication with control unit 'Battery' has a malfunction. The message is missing. |
| U012008 | - | This error code can be ignored and erased. |
| U012087 | - | Communication with the starter or alternator has a malfunction. The message is missing. |
| U012102 | - | Communication with ESP has a malfunction. There is a general signal fault. |
| U012287 | - | Communication with control unit 'Traction system' has a malfunction. The message is missing. |
| U012887 | - | Communication with the electric parking brake has a malfunction. The message is missing. |
| U013287 | - | Communication with control unit 'Suspension' has a malfunction. The message is missing. |
| U014000 | - | Communication with the signal acquisition and actuation module has a malfunction. |
| U014687 | - | Communication with the central gateway has a malfunction. The message is missing. |
| U015108 | - | Communication with the supplemental restraint system has a malfunction. There is a signal fault or the message is faulty. |
| U015187 | - | Communication with the supplemental restraint system has a malfunction. The message is missing. |
| U015500 | - | Communication with the instrument cluster has a malfunction. |
| U015587 | - | Communication with the instrument cluster has a malfunction. The message is missing. |
| U01558F | - | Communication with the instrument cluster has a malfunction. The signal or message is erratic. |
| U015987 | - | Communication with PARKTRONIC has a malfunction. The message is missing. |
| U016487 | - | Communication with the air conditioning has a malfunction. The message is missing. |
| U016887 | - | Communication with the electronic ignition lock has a malfunction. The message is missing. |
| U016B87 | - | Communication with the 'electric A/C compressor' control unit has a malfunction. The message is missing. |
| U019B00 | - | This error code can be ignored and erased. |
| U021287 | - | Communication with the steering column module has a malfunction. The message is missing. |
| U025900 | - | This error code can be ignored and erased. |
| U025908 | - | This error code can be ignored and erased. |
| U025987 | - | This error code can be ignored and erased. |
| U029287 | - | Communication with control unit 'Electric machine B' has a malfunction. The message is missing. |
| U029300 | - | This error code can be ignored and erased. |
| U029387 | - | Communication with control unit 'Hybrid system' has a malfunction. The message is missing. |
| U029487 | - | This error code can be ignored and erased. |
| U029887 | - | Communication with control unit 'DC/DC converter' has a malfunction. The message is missing. |
| U029A87 | - | Communication with the sensor module of the high-voltage battery module has a malfunction. The message is missing. |
| U029D87 | - | Communication with NOx sensor 1 has a malfunction. The message is missing. |
| U029E87 | - | Communication with NOx sensor 2 has a malfunction. The message is missing. |
| U040200 | - | Implausible data were received from control unit 'Transmission'. |
| U040208 | - | Implausible data were received from control unit 'Transmission'. There is a signal fault or the message is faulty. |
| U040308 | - | Implausible data were received from transfer case. There is a signal fault or the message is faulty. |
| U040400 | - | Implausible data were received from the electronic selector lever module. |
| U040408 | - | Implausible data were received from the electronic selector lever module. There is a signal fault or the message is faulty. |
| U040500 | - | Implausible data were received from the speed control system. |
| U040A00 | - | Implausible data were received from 'Air conditioning' control unit'. |
| U041108 | - | This error code can be ignored and erased. |
| U041208 | - | Implausible data were received from control unit 'Battery'. There is a signal fault or the message is faulty. |
| U041600 | - | Implausible data were received from control unit 'Traction system'. |
| U041608 | - | Implausible data were received from control unit 'Traction system'. There is a signal fault or the message is faulty. |
| U041681 | - | Implausible data were received from control unit 'Traction system'. Incorrect data were received. |
| U041708 | - | Implausible data were received from the electric parking brake. There is a signal fault or the message is faulty. |
| U041800 | - | Implausible data were received from control unit 'Regenerative braking system'. |
| U042108 | - | Implausible data were received from control unit 'Suspension'. There is a signal fault or the message is faulty. |
| U042300 | - | Implausible data were received from the instrument cluster. |
| U042400 | - | Implausible data were received from the air conditioning. |
| U042408 | - | Implausible data were received from the air conditioning. There is a signal fault or the message is faulty. |
| U04244A | - | Implausible data were received from the air conditioning. The wrong component is installed. |
| U042486 | - | Implausible data were received from the air conditioning. There is an incorrect signal. |
| U042708 | - | Implausible data were received from the electronic ignition lock. There is a signal fault or the message is faulty. |
| U042908 | - | Implausible data were received from the steering column module. There is a signal fault or the message is faulty. |
| U044708 | - | Implausible data were received from the central gateway. There is a signal fault or the message is faulty. |
| U046600 | - | This error code can be ignored and erased. |
| U046686 | - | This error code can be ignored and erased. |
| U046908 | - | This error code can be ignored and erased. |
| U051500 | - | This error code can be ignored and erased. |
| U059308 | - | Implausible data were received from control unit 'Electric machine B'. There is a signal fault or the message is faulty. |
| U059508 | - | This error code can be ignored and erased. |
| U104188 | - | Communication with the engine CAN bus has a malfunction. Bus OFF |
| U104787 | - | This error code can be ignored and erased. |
| U111029 | - | The vehicle speed signal was not received. There is an invalid signal. |
| U11A687 | - | Communication with control unit 'Radar sensorics' has a malfunction. The message is missing. |
| U11BE87 | - | Communication with the radiator shutters has a malfunction. The message is missing. |
| U120087 | - | Communication with NOx sensor 3 has a malfunction. The message is missing. |
| U120187 | - | Communication with NOx sensor 4 has a malfunction. The message is missing. |
| U14038F | - | This error code can be ignored and erased. |
| U140781 | - | Implausible signal 'Engine torque' was received. Incorrect data were received. |
| U140786 | - | Implausible signal 'Engine torque' was received. There is an incorrect signal. |
| U140787 | - | Implausible signal 'Engine torque' was received. The message is missing. |
| U140D29 | - | This error code can be ignored and erased. |
| U144408 | - | Implausible data were received from control unit 'Radar sensorics'. There is a signal fault or the message is faulty. |
| U145400 | - | Implausible data were received from the ethanol sensor. |
| U145700 | - | Signal 'Fuel level' from the rear signal acquisition and actuation module was not received by the instrument cluster. |
| U14572A | - | Signal 'Fuel level' from the rear signal acquisition and actuation module was not received by the instrument cluster. There is no signal change. |
| U151200 | - | This error code can be ignored and erased. |
| U151300 | - | This error code can be ignored and erased. |
| U151301 | - | This error code can be ignored and erased. |
| U151307 | - | This error code can be ignored and erased. |
| U151400 | - | This error code can be ignored and erased. |
| U187661 | - | Communication with control unit 'electric machine B' with the control unit 'combustion engine' via the hybrid CAN bus has a malfunction. The signal calculation is faulty. |
| U187662 | - | Communication with control unit 'electric machine B' with the control unit 'combustion engine' via the hybrid CAN bus has a malfunction. The signal comparison is faulty. |
| U187664 | - | Communication with control unit 'electric machine B' with the control unit 'combustion engine' via the hybrid CAN bus has a malfunction. There is an implausible signal. |
| U187668 | - | Communication with control unit 'electric machine B' with the control unit 'combustion engine' via the hybrid CAN bus has a malfunction. There is incomplete information. |
| U300316 | - | This error code can be ignored and erased. |
| U300317 | - | This error code can be ignored and erased. |
| U300E00 | - | Input signal 'Circuit 15 ON' is implausible. |
| U301100 | - | Input signal 'Circuit 15 OFF' is implausible. |