Ignition ON/OFF, Basic Function - GF07.10-S-1039A

Engine All (Light transporter) 

Overview 

This document contains information on:

• General 
• Function requirements 
• Function 

General 

The ignition ON function starts the engine management in the combustion engine control unit and prepares the combustion engine for starting.

The ignition OFF function switches off the combustion engine and then the engine management in the combustion engine control unit.

Function requirements 

• Ignition ON (circuit 15)

Function 

Ignition ON (circuit 15) 

Upon ignition ON, the electronic ignition lock control unit switches on the circuit 15 relay. Via the conducted on-board electrical system voltage, the engine management in the combustion engine control unit is started. The circuit status is also available to other systems via the vehicle bus systems.

The following functions start if the ignition is switched on and the engine management is started:

• To fully fill the low-pressure fuel circuit and build up pressure, the fuel pump is briefly actuated the first time the ignition is switched to ON after the vehicle has been unlocked.
• Engine diagnosis indicator lamp is actuated in instrument cluster.
• In diesel engines: preglow indicator lamp in instrument cluster and glow output stage are actuated.
• Fault memory in combustion engine control unit can be read out and deleted via the diagnostics connection.
• Diagnosis or correction programming can be performed via the diagnostics connection.
• Throttle valve actuator checks its return spring and performs an actuator adaptation if necessary.

Ignition OFF 

Additional function requirements:

• Engine management ON (circuit 87M)

If the ignition is switched off, the electronic ignition lock control unit switches off the circuit 15 relay. The circuit status is also available to other systems via the vehicle bus systems.

The following components are switched off if the ignition is switched off:

• Fuel pump (FP)
• Fuel injectors
• Quantity control valve
• With spark-ignition engines: ignition coils

The computer run-on of the combustion engine control unit also starts. In this connection, the time until the control unit changes to standby mode is involved.

	Function schematics
	Function schematic for ignition ON	Engine 654 in model 447.8 with code MO6 (Emissions class Euro 6d M/N1 Gr. II) with code MT6 (Emissions class Euro 6d N1 Gr.III/N2) with code XM0 (Facelift)	PE07.10-S-2505TRA
		Engine 654 in model 447.6/7 with code MO6 (Emissions class Euro 6d M/N1 Gr. II) with code MT6 (Emissions class Euro 6d N1 Gr.III/N2) with code XM0 (Facelift)	PE07.10-S-2505TRB
		Engine 654 in model 447.6/7 with code XM0 (Facelift) except code MO6 (Emissions class Euro 6d M/N1 Gr. II) except code MT6 (Emissions class Euro 6d N1 Gr.III/N2)	PE07.10-S-2505TRK
		Engine 654 in model 447.8 with code XM0 (Facelift) except code MO6 (Emissions class Euro 6d M/N1 Gr. II) except code MT6 (Emissions class Euro 6d N1 Gr.III/N2)	PE07.10-S-2505TRL
		Engine 200 in model 420	PE07.10-S-2505VRA
		Engine 608 in model 420	PE07.10-S-2505VRB
	Function schematic for ignition OFF	Engine 654 in model 447.8 with code MO6 (Emissions class Euro 6d M/N1 Gr. II) with code MT6 (Emissions class Euro 6d N1 Gr.III/N2) with code XM0 (Facelift)	PE07.10-S-2506TRA
		Engine 654 in model 447.6/7 with code MO6 (Emissions class Euro 6d M/N1 Gr. II) with code MT6 (Emissions class Euro 6d N1 Gr.III/N2) with code XM0 (Facelift)	PE07.10-S-2506TRB
		Engine 654 in model 447.6/7 with code XM0 (Facelift) except code MO6 (Emissions class Euro 6d M/N1 Gr. II) except code MT6 (Emissions class Euro 6d N1 Gr.III/N2)	PE07.10-S-2506TRK
		Engine 654 in model 447.8 with code XM0 (Facelift) except code MO6 (Emissions class Euro 6d M/N1 Gr. II) except code MT6 (Emissions class Euro 6d N1 Gr.III/N2)	PE07.10-S-2506TRL
		Engine 200 in model 420	PE07.10-S-2506VRA
		Engine 608 in model 420	PE07.10-S-2506VRB
	Control units
	Combustion engine control unit, basic function		GF07.08-S-9890A