Engine Control DTCS
ENGINE CONTROL DTCS (MRG1PI (ENGINE 256))
| MB DTC | Generic DTC | Description |
|---|---|---|
| B156000 | - | The CAN data required for theft protection are not present. |
| B1A6842 | - | The access protection of the control unit has a malfunction. There is a general memory error. |
| B1A6857 | - | The access protection of the control unit has a malfunction. The message is missing. |
| B1BA700 | - | A check of the airbag is necessary. |
| B1BA704 | - | A check of the airbag is necessary. There is an internal fault. |
| B25C000 | - | Switch 'Fuel filler flap' has a malfunction. |
| B273200 | - | The signal line for the crash signal has a malfunction. |
| C053C00 | - | The signal of the wheel speed sensors has a general malfunction. |
| P000000 | - | There is currently no further information available on this fault code. |
| P000100 | - | The quantity control valve has an electrical fault or an open circuit. |
| P000200 | - | The quantity control valve has a malfunction. |
| P00022B | - | The quantity control valve has a malfunction. The electrical lines have a short circuit to each other. |
| P000300 | - | The quantity control valve has a short circuit to ground. |
| P000400 | - | The quantity control valve has a short circuit to positive. |
| P000E00 | - | The adaptation values of the quantity control valve are outside the valid range. |
| P001000 | - | The actuator 'Intake camshaft' (cylinder bank 1) has an electrical fault or an open circuit. |
| P001013 | - | The actuator 'Intake camshaft' (cylinder bank 1) has an electrical fault or an open circuit. There is an open circuit. |
| P001100 | - | The position of the intake camshaft (cylinder bank 1) deviates from the specified value. |
| P001104 | - | The position of the intake camshaft (cylinder bank 1) deviates from the specified value. There is an internal fault. |
| P001200 | - | Adjustment of the intake camshaft (cylinder bank 1) is performed late. |
| P001300 | - | The actuator 'Exhaust camshaft' (cylinder bank 1) has an electrical fault or an open circuit. |
| P001313 | - | The actuator 'Exhaust camshaft' (cylinder bank 1) has an electrical fault or an open circuit. There is an open circuit. |
| P001400 | - | The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. |
| P001404 | - | The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value. There is an internal fault. |
| P001500 | - | Adjustment of the exhaust camshaft (cylinder bank 1) is performed late. |
| P001607 | - | The position of the intake camshaft (cylinder bank 1) is implausible relative to the position of the crankshaft. There is a mechanical fault. |
| P001654 | - | The position of the intake camshaft (cylinder bank 1) is implausible relative to the position of the crankshaft. Calibration is missing. |
| P001695 | - | The position of the intake camshaft (cylinder bank 1) is implausible relative to the position of the crankshaft. The mechanical setup is not OK. |
| P001707 | - | The position of the exhaust camshaft (cylinder bank 1) is implausible relative to the position of the crankshaft. There is a mechanical fault. |
| P001754 | - | The position of the exhaust camshaft (cylinder bank 1) is implausible relative to the position of the crankshaft. Calibration is missing. |
| P001795 | - | The position of the exhaust camshaft (cylinder bank 1) is implausible relative to the position of the crankshaft. The mechanical setup is not OK. |
| P001A00 | - | The output for solenoid 1 'Intake' (cylinder bank 1) for CAMTRONIC has an electrical fault or open circuit. |
| P001A13 | - | The output for solenoid 1 'Intake' (cylinder bank 1) for CAMTRONIC has an electrical fault or open circuit. There is an open circuit. |
| P001B00 | - | The output for solenoid 1 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to ground. |
| P001B11 | - | The output for solenoid 1 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to ground. There is a short circuit to ground. |
| P001C00 | - | The output for solenoid 1 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to positive. |
| P001C12 | - | The output for solenoid 1 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to positive. There is a short circuit to positive. |
| P003000 | - | The output for the heater of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. |
| P003100 | - | The output for the heater of oxygen sensor 1 (cylinder bank 1) has a short circuit to ground. |
| P003200 | - | The output for the heater of oxygen sensor 1 (cylinder bank 1) has a short circuit to positive. |
| P003300 | - | The output for the switchover valve of bypass flap 'Charge air' has an electrical fault. |
| P003400 | - | The output for the switchover valve of bypass flap 'Charge air' has a short circuit to ground. |
| P003500 | - | The output for the switchover valve of bypass flap 'Charge air' has a short circuit to positive. |
| P003600 | - | The output for the heater of oxygen sensor 2 (cylinder bank 1) has an electrical fault or open circuit. |
| P003613 | - | The output for the heater of oxygen sensor 2 (cylinder bank 1) has an electrical fault or open circuit. There is an open circuit. |
| P003700 | - | The output for the heater of oxygen sensor 2 (cylinder bank 1) has a short circuit to ground. |
| P003711 | - | The output for the heater of oxygen sensor 2 (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground. |
| P003800 | - | The output for the heater of oxygen sensor 2 (cylinder bank 1) has a short circuit to positive. |
| P003812 | - | The output for the heater of oxygen sensor 2 (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive. |
| P003900 | - | The output for the switchover valve of bypass flap 'Charge air' has a malfunction. |
| P003C00 | - | Solenoid 1 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. |
| P003C07 | - | Solenoid 1 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. There is a mechanical fault. |
| P003C09 | - | Solenoid 1 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. There is a component fault. |
| P003C53 | - | Solenoid 1 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. The component is deactivated. |
| P005400 | - | The heater of oxygen sensor 2 (cylinder bank 1) has an implausible resistance value. |
| P005A00 | - | Solenoid 1 'Exhaust' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. |
| P005A07 | - | Solenoid 1 'Exhaust' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. There is a mechanical fault. |
| P005A09 | - | Solenoid 1 'Exhaust' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. There is a component fault. |
| P007128 | - | The outside temperature sensor has a malfunction. The signal offset is outside the permissible range. |
| P007131 | - | The outside temperature sensor has a malfunction. The signal is not present. |
| P007211 | - | The outside temperature sensor has a short circuit to ground. There is a short circuit to ground. |
| P007312 | - | The outside temperature sensor has a short circuit to positive. There is a short circuit to positive. |
| P007315 | - | The outside temperature sensor has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P007427 | - | The outside temperature sensor has a sporadic malfunction. The signal change rate is above the permissible limit value. |
| P007B21 | - | The charge air temperature sensor (cylinder bank 1) has a malfunction. The signal amplitude is less than the minimum amplitude. |
| P007B22 | - | The charge air temperature sensor (cylinder bank 1) has a malfunction. The signal amplitude is greater than the maximum amplitude. |
| P007B28 | - | The charge air temperature sensor (cylinder bank 1) has a malfunction. The signal offset is outside the permissible range. |
| P007B2A | - | The charge air temperature sensor (cylinder bank 1) has a malfunction. There is no signal change. |
| P007B49 | - | The charge air temperature sensor (cylinder bank 1) has a malfunction. There is an internal electrical fault. |
| P008700 | - | The fuel pressure in the system is too low. |
| P008792 | - | The fuel pressure in the system is too low. The function or the instruction is faulty. |
| P008800 | - | The fuel pressure in the system is too high. |
| P008992 | - | Fuel pressure regulating valve 1 has a malfunction. The function or the instruction is faulty. |
| P008994 | - | Fuel pressure regulating valve 1 has a malfunction. There is an unexpected instruction. |
| P008A00 | - | The pressure in the fuel low pressure circuit is too low. |
| P008A04 | - | The pressure in the fuel low pressure circuit is too low. There is an internal fault. |
| P008A84 | - | The pressure in the fuel low pressure circuit is too low. There is a signal below the permissible limit value. |
| P008AFA | - | The pressure in the fuel low pressure circuit is too low. |
| P009400 | - | There is currently no further information available on this fault code. |
| P009621 | - | Intake air temperature sensor 2 (cylinder bank 1) has a malfunction. The signal amplitude is less than the minimum amplitude. |
| P009622 | - | Intake air temperature sensor 2 (cylinder bank 1) has a malfunction. The signal amplitude is greater than the maximum amplitude. |
| P009628 | - | Intake air temperature sensor 2 (cylinder bank 1) has a malfunction. The signal offset is outside the permissible range. |
| P00962A | - | Intake air temperature sensor 2 (cylinder bank 1) has a malfunction. There is no signal change. |
| P009649 | - | Intake air temperature sensor 2 (cylinder bank 1) has a malfunction. There is an internal electrical fault. |
| P00C600 | - | The fuel pressure in the system during the starting procedure is too low. |
| P00DF28 | - | The temperature sensor for the coolant of the charge air cooler has a malfunction. The signal offset is outside the permissible range. |
| P00DF2A | - | The temperature sensor for the coolant of the charge air cooler has a malfunction. There is no signal change. |
| P00DF84 | - | The temperature sensor for the coolant of the charge air cooler has a malfunction. There is a signal below the permissible limit value. |
| P00DF85 | - | The temperature sensor for the coolant of the charge air cooler has a malfunction. There is a signal above the permissible limit value. |
| P00E000 | - | The temperature sensor for the coolant of the charge air cooler has a short circuit to ground. |
| P00E011 | - | The temperature sensor for the coolant of the charge air cooler has a short circuit to ground. There is a short circuit to ground. |
| P00E021 | - | The temperature sensor for the coolant of the charge air cooler has a short circuit to ground. The signal amplitude is less than the minimum amplitude. |
| P00E084 | - | The temperature sensor for the coolant of the charge air cooler has a short circuit to ground. There is a signal below the permissible limit value. |
| P00E100 | - | The temperature sensor for the coolant of the charge air cooler has a short circuit to positive. |
| P00E112 | - | The temperature sensor for the coolant of the charge air cooler has a short circuit to positive. There is a short circuit to positive. |
| P00E115 | - | The temperature sensor for the coolant of the charge air cooler has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P00E122 | - | The temperature sensor for the coolant of the charge air cooler has a short circuit to positive. The signal amplitude is greater than the maximum amplitude. |
| P00E185 | - | The temperature sensor for the coolant of the charge air cooler has a short circuit to positive. There is a signal above the permissible limit value. |
| P00E200 | - | The temperature sensor for the coolant of the charge air cooler has a sporadic malfunction. |
| P00E227 | - | The temperature sensor for the coolant of the charge air cooler has a sporadic malfunction. The signal change rate is above the permissible limit value. |
| P00FE00 | - | The bleed line of the fuel tank is blocked. |
| P010600 | - | The intake manifold pressure sensor has a malfunction. |
| P010621 | - | The intake manifold pressure sensor has a malfunction. The signal amplitude is less than the minimum amplitude. |
| P010622 | - | The intake manifold pressure sensor has a malfunction. The signal amplitude is greater than the maximum amplitude. |
| P010627 | - | The intake manifold pressure sensor has a malfunction. The signal change rate is above the permissible limit value. |
| P010628 | - | The intake manifold pressure sensor has a malfunction. The signal offset is outside the permissible range. |
| P01062A | - | The intake manifold pressure sensor has a malfunction. There is no signal change. |
| P010649 | - | The intake manifold pressure sensor has a malfunction. There is an internal electrical fault. |
| P010667 | - | The intake manifold pressure sensor has a malfunction. The signal is impermissible after an event. |
| P010684 | - | The intake manifold pressure sensor has a malfunction. There is a signal below the permissible limit value. |
| P010685 | - | The intake manifold pressure sensor has a malfunction. There is a signal above the permissible limit value. |
| P010700 | - | The intake manifold pressure sensor has a short circuit to ground. |
| P010711 | - | The intake manifold pressure sensor has a short circuit to ground. There is a short circuit to ground. |
| P010800 | - | The intake manifold pressure sensor has a short circuit to positive. |
| P010815 | - | The intake manifold pressure sensor has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P010927 | - | The intake manifold pressure sensor has a malfunction. The signal change rate is above the permissible limit value. |
| P011128 | - | Intake air temperature sensor 1 (cylinder bank 1) has a malfunction. The signal offset is outside the permissible range. |
| P01112A | - | Intake air temperature sensor 1 (cylinder bank 1) has a malfunction. There is no signal change. |
| P011149 | - | Intake air temperature sensor 1 (cylinder bank 1) has a malfunction. There is an internal electrical fault. |
| P011184 | - | Intake air temperature sensor 1 (cylinder bank 1) has a malfunction. There is a signal below the permissible limit value. |
| P011185 | - | Intake air temperature sensor 1 (cylinder bank 1) has a malfunction. There is a signal above the permissible limit value. |
| P011200 | - | Intake air temperature sensor 1 (cylinder bank 1) has a short circuit to ground. |
| P011211 | - | Intake air temperature sensor 1 (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground. |
| P011300 | - | Intake air temperature sensor 1 (cylinder bank 1) has a short circuit to positive. |
| P011315 | - | Intake air temperature sensor 1 (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P011400 | - | Intake air temperature sensor 1 (cylinder bank 1) has a sporadic malfunction. |
| P011427 | - | Intake air temperature sensor 1 (cylinder bank 1) has a sporadic malfunction. The signal change rate is above the permissible limit value. |
| P011600 | - | Coolant temperature sensor 1 has a malfunction. |
| P011623 | - | Coolant temperature sensor 1 has a malfunction. No signal change: Voltage level is too low. |
| P011628 | - | Coolant temperature sensor 1 has a malfunction. The signal offset is outside the permissible range. |
| P01162A | - | Coolant temperature sensor 1 has a malfunction. There is no signal change. |
| P011684 | - | Coolant temperature sensor 1 has a malfunction. There is a signal below the permissible limit value. |
| P011685 | - | Coolant temperature sensor 1 has a malfunction. There is a signal above the permissible limit value. |
| P011698 | - | Coolant temperature sensor 1 has a malfunction. The component or the system has overtemperature. |
| P01169D | - | Coolant temperature sensor 1 has a malfunction. The component or the system has undertemperature. |
| P011711 | - | Coolant temperature sensor 1 has a short circuit to ground. There is a short circuit to ground. |
| P011721 | - | Coolant temperature sensor 1 has a short circuit to ground. The signal amplitude is less than the minimum amplitude. |
| P011812 | - | Coolant temperature sensor 1 has a short circuit to positive. There is a short circuit to positive. |
| P011815 | - | Coolant temperature sensor 1 has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P011822 | - | Coolant temperature sensor 1 has a short circuit to positive. The signal amplitude is greater than the maximum amplitude. |
| P011900 | - | Coolant temperature sensor 1 has a sporadic malfunction. |
| P011927 | - | Coolant temperature sensor 1 has a sporadic malfunction. The signal change rate is above the permissible limit value. |
| P012200 | - | Position sensor 1 for the throttle valve has a short circuit to ground. |
| P012300 | - | Position sensor 1 for the throttle valve has a short circuit to positive. |
| P012800 | - | The coolant temperature is below the coolant thermostat specified temperature. |
| P012867 | - | The coolant temperature is below the coolant thermostat specified temperature. The signal is impermissible after an event. |
| P012A49 | - | The pressure sensor upstream of turbocharger has an electrical fault. There is an internal electrical fault. |
| P012B27 | - | The pressure sensor upstream of the turbocharger has a malfunction. The signal change rate is above the permissible limit value. |
| P012B28 | - | The pressure sensor upstream of the turbocharger has a malfunction. The signal offset is outside the permissible range. |
| P012B49 | - | The pressure sensor upstream of the turbocharger has a malfunction. There is an internal electrical fault. |
| P012B84 | - | The pressure sensor upstream of the turbocharger has a malfunction. There is a signal below the permissible limit value. |
| P012B85 | - | The pressure sensor upstream of the turbocharger has a malfunction. There is a signal above the permissible limit value. |
| P012C11 | - | The pressure sensor upstream of the turbocharger has a short circuit to ground. There is a short circuit to ground. |
| P012C21 | - | The pressure sensor upstream of the turbocharger has a short circuit to ground. The signal amplitude is less than the minimum amplitude. |
| P012D12 | - | The pressure sensor upstream of the turbocharger has a short circuit to positive. There is a short circuit to positive. |
| P012D15 | - | The pressure sensor upstream of the turbocharger has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P012D22 | - | The pressure sensor upstream of the turbocharger has a short circuit to positive. The signal amplitude is greater than the maximum amplitude. |
| P012E27 | - | The pressure sensor upstream of the turbocharger has a sporadic malfunction. The signal change rate is above the permissible limit value. |
| P013100 | - | Oxygen sensor 1 (cylinder bank 1) has a short circuit to ground. |
| P013200 | - | Oxygen sensor 1 (cylinder bank 1) has a short circuit to positive. |
| P013300 | - | Oxygen sensor 1 (cylinder bank 1) has a delayed reaction. |
| P013400 | - | The signal of lambda sensor 1 (cylinder bank 1) does not change. |
| P013500 | - | The heater for oxygen sensor 1 (cylinder bank 1) has an electrical fault. |
| P013600 | - | Oxygen sensor 2 (cylinder bank 1) has an electrical fault. |
| P013700 | - | Oxygen sensor 2 (cylinder bank 1) has a short circuit to ground. |
| P013800 | - | Oxygen sensor 2 (cylinder bank 1) has a short circuit to positive. |
| P013A00 | - | The rich/lean switchover of oxygen sensor 2 (cylinder bank 1) is too slow. |
| P013B00 | - | The lean/rich switchover of oxygen sensor 2 (cylinder bank 1) is too slow. |
| P013E00 | - | The rich/lean switchover of oxygen sensor 2 (cylinder bank 1) is delayed. |
| P013F00 | - | The lean/rich switchover of oxygen sensor 2 (cylinder bank 1) is delayed. |
| P014000 | - | The signal of oxygen sensor 2 (cylinder bank 1) does not change. |
| P014100 | - | The heater for oxygen sensor 2 (cylinder bank 1) has an electrical fault. |
| P014800 | - | The fuel supply has a fault. |
| P016A00 | - | The waiting time for enabling of lambda control has been exceeded. |
| P017100 | - | The mixture (cylinder bank 1) is too lean. |
| P017200 | - | The mixture (cylinder bank 1) is too rich. |
| P017600 | - | The fuel quality sensor has an electrical fault. |
| P017700 | - | The fuel quality sensor has a malfunction. |
| P017800 | - | The fuel quality sensor has a short circuit to ground. |
| P017900 | - | The fuel quality sensor has a short circuit to positive. |
| P017F00 | - | The air filter in the diagnostic module of the evaporative emission control system is clogged. |
| P018121 | - | The fuel temperature sensor has a malfunction. The signal amplitude is less than the minimum amplitude. |
| P018122 | - | The fuel temperature sensor has a malfunction. The signal amplitude is greater than the maximum amplitude. |
| P018128 | - | The fuel temperature sensor has a malfunction. The signal offset is outside the permissible range. |
| P01812A | - | The fuel temperature sensor has a malfunction. There is no signal change. |
| P018149 | - | The fuel temperature sensor has a malfunction. There is an internal electrical fault. |
| P018184 | - | The fuel temperature sensor has a malfunction. There is a signal below the permissible limit value. |
| P018185 | - | The fuel temperature sensor has a malfunction. There is a signal above the permissible limit value. |
| P019116 | - | The rail pressure sensor has a malfunction. The limit value for electrical voltage has not been attained. |
| P019117 | - | The rail pressure sensor has a malfunction. The limit value for electrical voltage has been exceeded. |
| P01912A | - | The rail pressure sensor has a malfunction. There is no signal change. |
| P019149 | - | The rail pressure sensor has a malfunction. There is an internal electrical fault. |
| P019184 | - | The rail pressure sensor has a malfunction. There is a signal below the permissible limit value. |
| P019185 | - | The rail pressure sensor has a malfunction. There is a signal above the permissible limit value. |
| P019196 | - | The rail pressure sensor has a malfunction. There is an internal component fault. |
| P01961C | - | Engine oil temperature sensor 1 has a malfunction. The voltage value is outside the permissible range. |
| P019621 | - | Engine oil temperature sensor 1 has a malfunction. The signal amplitude is less than the minimum amplitude. |
| P019622 | - | Engine oil temperature sensor 1 has a malfunction. The signal amplitude is greater than the maximum amplitude. |
| P019627 | - | Engine oil temperature sensor 1 has a malfunction. The signal change rate is above the permissible limit value. |
| P019628 | - | Engine oil temperature sensor 1 has a malfunction. The signal offset is outside the permissible range. |
| P01962A | - | Engine oil temperature sensor 1 has a malfunction. There is no signal change. |
| P019649 | - | Engine oil temperature sensor 1 has a malfunction. There is an internal electrical fault. |
| P019684 | - | Engine oil temperature sensor 1 has a malfunction. There is a signal below the permissible limit value. |
| P019685 | - | Engine oil temperature sensor 1 has a malfunction. There is a signal above the permissible limit value. |
| P019711 | - | Engine oil temperature sensor 1 has a short circuit to ground. There is a short circuit to ground. |
| P019754 | - | Engine oil temperature sensor 1 has a short circuit to ground. Calibration is missing. |
| P019815 | - | Engine oil temperature sensor 1 has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P019855 | - | Engine oil temperature sensor 1 has a short circuit to positive. The component is not configured. |
| P020101 | - | The fuel injector (cylinder 1) has an electrical fault or an open circuit. There is a general electrical fault. |
| P020111 | - | The fuel injector (cylinder 1) has an electrical fault or an open circuit. There is a short circuit to ground. |
| P020113 | - | The fuel injector (cylinder 1) has an electrical fault or an open circuit. There is an open circuit. |
| P020119 | - | The fuel injector (cylinder 1) has an electrical fault or an open circuit. The limit value for current has been exceeded. |
| P02011F | - | The fuel injector (cylinder 1) has an electrical fault or an open circuit. There is a sporadic fault. |
| P020149 | - | The fuel injector (cylinder 1) has an electrical fault or an open circuit. There is an internal electrical fault. |
| P020192 | - | The fuel injector (cylinder 1) has an electrical fault or an open circuit. The function or the instruction is faulty. |
| P020201 | - | The fuel injector (cylinder 2) has an electrical fault or an open circuit. There is a general electrical fault. |
| P020211 | - | The fuel injector (cylinder 2) has an electrical fault or an open circuit. There is a short circuit to ground. |
| P020213 | - | The fuel injector (cylinder 2) has an electrical fault or an open circuit. There is an open circuit. |
| P020219 | - | The fuel injector (cylinder 2) has an electrical fault or an open circuit. The limit value for current has been exceeded. |
| P02021F | - | The fuel injector (cylinder 2) has an electrical fault or an open circuit. There is a sporadic fault. |
| P020249 | - | The fuel injector (cylinder 2) has an electrical fault or an open circuit. There is an internal electrical fault. |
| P020292 | - | The fuel injector (cylinder 2) has an electrical fault or an open circuit. The function or the instruction is faulty. |
| P020301 | - | The fuel injector (cylinder 3) has an electrical fault or an open circuit. There is a general electrical fault. |
| P020311 | - | The fuel injector (cylinder 3) has an electrical fault or an open circuit. There is a short circuit to ground. |
| P020313 | - | The fuel injector (cylinder 3) has an electrical fault or an open circuit. There is an open circuit. |
| P020319 | - | The fuel injector (cylinder 3) has an electrical fault or an open circuit. The limit value for current has been exceeded. |
| P02031F | - | The fuel injector (cylinder 3) has an electrical fault or an open circuit. There is a sporadic fault. |
| P020349 | - | The fuel injector (cylinder 3) has an electrical fault or an open circuit. There is an internal electrical fault. |
| P020392 | - | The fuel injector (cylinder 3) has an electrical fault or an open circuit. The function or the instruction is faulty. |
| P020401 | - | The fuel injector (cylinder 4) has an electrical fault or an open circuit. There is a general electrical fault. |
| P020411 | - | The fuel injector (cylinder 4) has an electrical fault or an open circuit. There is a short circuit to ground. |
| P020413 | - | The fuel injector (cylinder 4) has an electrical fault or an open circuit. There is an open circuit. |
| P020419 | - | The fuel injector (cylinder 4) has an electrical fault or an open circuit. The limit value for current has been exceeded. |
| P02041F | - | The fuel injector (cylinder 4) has an electrical fault or an open circuit. There is a sporadic fault. |
| P020449 | - | The fuel injector (cylinder 4) has an electrical fault or an open circuit. There is an internal electrical fault. |
| P020492 | - | The fuel injector (cylinder 4) has an electrical fault or an open circuit. The function or the instruction is faulty. |
| P020501 | - | The fuel injector (cylinder 5) has an electrical fault or an open circuit. There is a general electrical fault. |
| P020511 | - | The fuel injector (cylinder 5) has an electrical fault or an open circuit. There is a short circuit to ground. |
| P020513 | - | The fuel injector (cylinder 5) has an electrical fault or an open circuit. There is an open circuit. |
| P020519 | - | The fuel injector (cylinder 5) has an electrical fault or an open circuit. The limit value for current has been exceeded. |
| P02051F | - | The fuel injector (cylinder 5) has an electrical fault or an open circuit. There is a sporadic fault. |
| P020549 | - | The fuel injector (cylinder 5) has an electrical fault or an open circuit. There is an internal electrical fault. |
| P020592 | - | The fuel injector (cylinder 5) has an electrical fault or an open circuit. The function or the instruction is faulty. |
| P020601 | - | The fuel injector (cylinder 6) has an electrical fault or an open circuit. There is a general electrical fault. |
| P020611 | - | The fuel injector (cylinder 6) has an electrical fault or an open circuit. There is a short circuit to ground. |
| P020613 | - | The fuel injector (cylinder 6) has an electrical fault or an open circuit. There is an open circuit. |
| P020619 | - | The fuel injector (cylinder 6) has an electrical fault or an open circuit. The limit value for current has been exceeded. |
| P02061F | - | The fuel injector (cylinder 6) has an electrical fault or an open circuit. There is a sporadic fault. |
| P020649 | - | The fuel injector (cylinder 6) has an electrical fault or an open circuit. There is an internal electrical fault. |
| P020692 | - | The fuel injector (cylinder 6) has an electrical fault or an open circuit. The function or the instruction is faulty. |
| P021700 | - | The coolant temperature of the engine is too high. |
| P022200 | - | Position sensor 2 for the throttle valve has a short circuit to ground. |
| P022300 | - | Position sensor 2 for the throttle valve has a short circuit to positive. |
| P023400 | - | The boost pressure of turbocharger 1 is too high. |
| P023409 | - | The boost pressure of turbocharger 1 is too high. There is a component fault. |
| P023621 | - | The boost pressure sensor has a malfunction. The signal amplitude is less than the minimum amplitude. |
| P023622 | - | The boost pressure sensor has a malfunction. The signal amplitude is greater than the maximum amplitude. |
| P023627 | - | The boost pressure sensor has a malfunction. The signal change rate is above the permissible limit value. |
| P023628 | - | The boost pressure sensor has a malfunction. The signal offset is outside the permissible range. |
| P02362A | - | The boost pressure sensor has a malfunction. There is no signal change. |
| P023649 | - | The boost pressure sensor has a malfunction. There is an internal electrical fault. |
| P023667 | - | The boost pressure sensor has a malfunction. The signal is impermissible after an event. |
| P023668 | - | The boost pressure sensor has a malfunction. There is incomplete information. |
| P023684 | - | The boost pressure sensor has a malfunction. There is a signal below the permissible limit value. |
| P023685 | - | The boost pressure sensor has a malfunction. There is a signal above the permissible limit value. |
| P023700 | - | The boost pressure sensor has a short circuit to ground. |
| P023711 | - | The boost pressure sensor has a short circuit to ground. There is a short circuit to ground. |
| P023800 | - | The boost pressure sensor has a short circuit to positive. |
| P023815 | - | The boost pressure sensor has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P024400 | - | The output for the low-pressure turbocharger has a malfunction. |
| P024498 | - | The output for the low-pressure turbocharger has a malfunction. The component or the system has overtemperature. |
| P024500 | - | The output for the low-pressure turbocharger has a short circuit to ground. |
| P024513 | - | The output for the low-pressure turbocharger has a short circuit to ground. There is an open circuit. |
| P026200 | - | The fuel injector (cylinder 1) has a short circuit to positive. |
| P026212 | - | The fuel injector (cylinder 1) has a short circuit to positive. There is a short circuit to positive. |
| P026500 | - | The fuel injector (cylinder 2) has a short circuit to positive. |
| P026512 | - | The fuel injector (cylinder 2) has a short circuit to positive. There is a short circuit to positive. |
| P026800 | - | The fuel injector (cylinder 3) has a short circuit to positive. |
| P026812 | - | The fuel injector (cylinder 3) has a short circuit to positive. There is a short circuit to positive. |
| P026A00 | - | The efficiency of the charge air cooler is not sufficient. |
| P027100 | - | The fuel injector (cylinder 4) has a short circuit to positive. |
| P027112 | - | The fuel injector (cylinder 4) has a short circuit to positive. There is a short circuit to positive. |
| P027400 | - | The fuel injector (cylinder 5) has a short circuit to positive. |
| P027412 | - | The fuel injector (cylinder 5) has a short circuit to positive. There is a short circuit to positive. |
| P027700 | - | The fuel injector (cylinder 6) has a short circuit to positive. |
| P027712 | - | The fuel injector (cylinder 6) has a short circuit to positive. There is a short circuit to positive. |
| P029900 | - | The boost pressure of turbocharger 1 is too low. |
| P029909 | - | The boost pressure of turbocharger 1 is too low. There is a component fault. |
| P029A00 | - | Quantity correction for cylinder 1 has reached the upper limit value. |
| P029B00 | - | Quantity correction for cylinder 1 has reached the lower limit value. |
| P029E00 | - | Quantity correction for cylinder 2 has reached the upper limit value. |
| P029F00 | - | Quantity correction for cylinder 2 has reached the lower limit value. |
| P02A200 | - | Quantity correction for cylinder 3 has reached the upper limit value. |
| P02A300 | - | Quantity correction for cylinder 3 has reached the lower limit value. |
| P02A600 | - | Quantity correction for cylinder 4 has reached the upper limit value. |
| P02A700 | - | Quantity correction for cylinder 4 has reached the lower limit value. |
| P02AA00 | - | Quantity correction for cylinder 5 has reached the upper limit value. |
| P02AB00 | - | Quantity correction for cylinder 5 has reached the lower limit value. |
| P02AE00 | - | Quantity correction for cylinder 6 has reached the upper limit value. |
| P02AF00 | - | Quantity correction for cylinder 6 has reached the lower limit value. |
| P02FF02 | - | The engine off time has an implausible value. There is a general signal fault. |
| P02FF08 | - | The engine off time has an implausible value. There is a signal fault or the message is faulty. |
| P02FF65 | - | The engine off time has an implausible value. The signal has too few transitions or events. |
| P02FF66 | - | The engine off time has an implausible value. The signal has too many transitions or events. |
| P02FF84 | - | The engine off time has an implausible value. There is a signal below the permissible limit value. |
| P02FF85 | - | The engine off time has an implausible value. There is a signal above the permissible limit value. |
| P030000 | - | Combustion misfiring has been detected. |
| P030001 | - | Combustion misfiring has been detected. There is a general electrical fault. |
| P030002 | - | Combustion misfiring has been detected. There is a general signal fault. |
| P030004 | - | Combustion misfiring has been detected. There is an internal fault. |
| P03001F | - | Combustion misfiring has been detected. There is a sporadic fault. |
| P030021 | - | Combustion misfiring has been detected. The signal amplitude is less than the minimum amplitude. |
| P030022 | - | Combustion misfiring has been detected. The signal amplitude is greater than the maximum amplitude. |
| P030084 | - | Combustion misfiring has been detected. There is a signal below the permissible limit value. |
| P030100 | - | Combustion misfiring of cylinder 1 has been detected. |
| P030200 | - | Combustion misfiring of cylinder 2 has been detected. |
| P030300 | - | Combustion misfiring of cylinder 3 has been detected. |
| P030400 | - | Combustion misfiring of cylinder 4 has been detected. |
| P030500 | - | Combustion misfiring of cylinder 5 has been detected. |
| P030600 | - | Combustion misfiring of cylinder 6 has been detected. |
| P031500 | - | Sensor rotor adaptation has not been performed. |
| P031554 | - | Sensor rotor adaptation has not been performed. Calibration is missing. |
| P031600 | - | Combustion misfires were detected at engine start. |
| P032400 | - | The knock control has a malfunction. |
| P032427 | - | The knock control has a malfunction. The signal change rate is above the permissible limit value. |
| P032711 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground. |
| P032714 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground or an open circuit. |
| P032784 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to ground. There is a signal below the permissible limit value. |
| P032812 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive. |
| P032815 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P032885 | - | Knock sensor 1 (cylinder bank 1) has a short circuit to positive. There is a signal above the permissible limit value. |
| P032C11 | - | Knock sensor 2 (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground. |
| P032C14 | - | Knock sensor 2 (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground or an open circuit. |
| P032C84 | - | Knock sensor 2 (cylinder bank 1) has a short circuit to ground. There is a signal below the permissible limit value. |
| P032D12 | - | Knock sensor 2 (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive. |
| P032D15 | - | Knock sensor 2 (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P032D85 | - | Knock sensor 2 (cylinder bank 1) has a short circuit to positive. There is a signal above the permissible limit value. |
| P033603 | - | Position sensor 1 for the crankshaft has a malfunction. There is a frequency or pulse width modulation fault. |
| P033609 | - | Position sensor 1 for the crankshaft has a malfunction. There is a component fault. |
| P03362F | - | Position sensor 1 for the crankshaft has a malfunction. There is an erratic signal. |
| P033664 | - | Position sensor 1 for the crankshaft has a malfunction. There is an implausible signal. |
| P033700 | - | Position sensor 1 for the crankshaft has a short circuit to ground. |
| P033800 | - | Position sensor 1 for the crankshaft has a short circuit to positive. |
| P033815 | - | Position sensor 1 for the crankshaft has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P033900 | - | Position sensor 1 for the crankshaft has a sporadic malfunction. |
| P03391F | - | Position sensor 1 for the crankshaft has a sporadic malfunction. There is a sporadic fault. |
| P034100 | - | The position sensor for the intake camshaft (cylinder bank 1) has a malfunction. |
| P03412F | - | The position sensor for the intake camshaft (cylinder bank 1) has a malfunction. There is an erratic signal. |
| P034200 | - | The position sensor of the intake camshaft (cylinder bank 1) has a short circuit to ground. |
| P034300 | - | The position sensor of the intake camshaft (cylinder bank 1) has a short circuit to positive. |
| P034315 | - | The position sensor of the intake camshaft (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P034A00 | - | The position calculated via the position sensor of the crankshaft does not match the start position of the combustion engine. |
| P034B00 | - | The position sensor of the crankshaft has detected an incorrect rotation direction. |
| P034B62 | - | The position sensor of the crankshaft has detected an incorrect rotation direction. The signal comparison is faulty. |
| P034B64 | - | The position sensor of the crankshaft has detected an incorrect rotation direction. There is an implausible signal. |
| P035107 | - | The actuation of ignition coil 1 has an electrical fault or open circuit. There is a mechanical fault. |
| P035113 | - | The actuation of ignition coil 1 has an electrical fault or open circuit. There is an open circuit. |
| P035149 | - | The actuation of ignition coil 1 has an electrical fault or open circuit. There is an internal electrical fault. |
| P035196 | - | The actuation of ignition coil 1 has an electrical fault or open circuit. There is an internal component fault. |
| P035207 | - | The actuation of ignition coil 2 has an electrical fault or open circuit. There is a mechanical fault. |
| P035213 | - | The actuation of ignition coil 2 has an electrical fault or open circuit. There is an open circuit. |
| P035249 | - | The actuation of ignition coil 2 has an electrical fault or open circuit. There is an internal electrical fault. |
| P035296 | - | The actuation of ignition coil 2 has an electrical fault or open circuit. There is an internal component fault. |
| P035307 | - | The actuation of ignition coil 3 has an electrical fault or open circuit. There is a mechanical fault. |
| P035313 | - | The actuation of ignition coil 3 has an electrical fault or open circuit. There is an open circuit. |
| P035349 | - | The actuation of ignition coil 3 has an electrical fault or open circuit. There is an internal electrical fault. |
| P035396 | - | The actuation of ignition coil 3 has an electrical fault or open circuit. There is an internal component fault. |
| P035407 | - | The actuation of ignition coil 4 has an electrical fault or open circuit. There is a mechanical fault. |
| P035413 | - | The actuation of ignition coil 4 has an electrical fault or open circuit. There is an open circuit. |
| P035449 | - | The actuation of ignition coil 4 has an electrical fault or open circuit. There is an internal electrical fault. |
| P035496 | - | The actuation of ignition coil 4 has an electrical fault or open circuit. There is an internal component fault. |
| P035507 | - | The actuation of ignition coil 5 has an electrical fault or open circuit. There is a mechanical fault. |
| P035513 | - | The actuation of ignition coil 5 has an electrical fault or open circuit. There is an open circuit. |
| P035549 | - | The actuation of ignition coil 5 has an electrical fault or open circuit. There is an internal electrical fault. |
| P035596 | - | The actuation of ignition coil 5 has an electrical fault or open circuit. There is an internal component fault. |
| P035607 | - | The actuation of ignition coil 6 has an electrical fault or open circuit. There is a mechanical fault. |
| P035613 | - | The actuation of ignition coil 6 has an electrical fault or open circuit. There is an open circuit. |
| P035649 | - | The actuation of ignition coil 6 has an electrical fault or open circuit. There is an internal electrical fault. |
| P035696 | - | The actuation of ignition coil 6 has an electrical fault or open circuit. There is an internal component fault. |
| P036301 | - | Injector shutoff was activated due to a combustion misfire. There is a general electrical fault. |
| P036327 | - | Injector shutoff was activated due to a combustion misfire. The signal change rate is above the permissible limit value. |
| P036600 | - | The position sensor for the exhaust camshaft (cylinder bank 1) has a malfunction. |
| P03662F | - | The position sensor for the exhaust camshaft (cylinder bank 1) has a malfunction. There is an erratic signal. |
| P036700 | - | The position sensor of the exhaust camshaft (cylinder bank 1) has a short circuit to ground. |
| P036800 | - | The position sensor of the exhaust camshaft (cylinder bank 1) has a short circuit to positive. |
| P036815 | - | The position sensor of the exhaust camshaft (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P03E600 | - | The sensor signal of solenoid 3 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction. |
| P03E609 | - | The sensor signal of solenoid 3 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction. There is a component fault. |
| P03E700 | - | The sensor signal of solenoid 3 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to ground. |
| P03E800 | - | The sensor signal of solenoid 3 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to positive. |
| P03EC00 | - | The output for solenoid 3 'Intake' (cylinder bank 1) for CAMTRONIC has an electrical fault or open circuit. |
| P03EC13 | - | The output for solenoid 3 'Intake' (cylinder bank 1) for CAMTRONIC has an electrical fault or open circuit. There is an open circuit. |
| P03ED00 | - | The output for solenoid 3 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to ground. |
| P03ED11 | - | The output for solenoid 3 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to ground. There is a short circuit to ground. |
| P03EE00 | - | The output for solenoid 3 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to positive. |
| P03EE12 | - | The output for solenoid 3 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to positive. There is a short circuit to positive. |
| P03EF00 | - | Solenoid 3 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. |
| P03EF07 | - | Solenoid 3 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. There is a mechanical fault. |
| P03EF09 | - | Solenoid 3 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. There is a component fault. |
| P03F400 | - | Solenoid 3 'Exhaust' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. |
| P03F407 | - | Solenoid 3 'Exhaust' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. There is a mechanical fault. |
| P03F409 | - | Solenoid 3 'Exhaust' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. There is a component fault. |
| P03F700 | - | The sensor signal of solenoid 3 'Exhaust' (cylinder bank 1) for CAMTRONIC has a malfunction. |
| P03F709 | - | The sensor signal of solenoid 3 'Exhaust' (cylinder bank 1) for CAMTRONIC has a malfunction. There is a component fault. |
| P03F800 | - | The sensor signal of solenoid 3 'Exhaust' (cylinder bank 1) for CAMTRONIC has a short circuit to ground. |
| P03F900 | - | The sensor signal of solenoid 3 'Exhaust' (cylinder bank 1) for CAMTRONIC has a short circuit to positive. |
| P042000 | - | The efficiency of the catalytic converter (cylinder bank 1) is insufficient. |
| P044100 | - | The purge flow from the evaporative emission control system deviates from the specified value. |
| P044107 | - | The purge flow from the evaporative emission control system deviates from the specified value. |
| P044209 | - | A fine leak in the evaporative emission control system was detected. There is a component fault. |
| P044256 | - | A fine leak in the evaporative emission control system was detected. An incorrect or incompatible configuration was detected. |
| P04427A | - | A fine leak in the evaporative emission control system was detected. Leakage or a defective seal was detected. |
| P044400 | - | The purge valve of the evaporative emission control system has an open circuit. |
| P044700 | - | The shutoff valve of the activated charcoal canister has an open circuit. |
| P045116 | - | The pressure sensor/pressure switch of the evaporative emission control system has a malfunction. The limit value for electrical voltage has not been attained. |
| P045117 | - | The pressure sensor/pressure switch of the evaporative emission control system has a malfunction. The limit value for electrical voltage has been exceeded. |
| P045126 | - | The pressure sensor/pressure switch of the evaporative emission control system has a malfunction. The signal change rate is below the permissible limit value. |
| P045128 | - | The pressure sensor/pressure switch of the evaporative emission control system has a malfunction. The signal offset is outside the permissible range. |
| P04512F | - | The pressure sensor/pressure switch of the evaporative emission control system has a malfunction. There is an erratic signal. |
| P045200 | - | The pressure sensor/pressure switch of the evaporative emission control system has a short circuit to ground. |
| P045211 | - | The pressure sensor/pressure switch of the evaporative emission control system has a short circuit to ground. There is a short circuit to ground. |
| P045300 | - | The pressure sensor/pressure switch of the evaporative emission control system has a short circuit to positive. |
| P045312 | - | The pressure sensor/pressure switch of the evaporative emission control system has a short circuit to positive. There is a short circuit to positive. |
| P045500 | - | A gross leak in the evaporative emission control system was detected. |
| P045509 | - | A gross leak in the evaporative emission control system was detected. There is a component fault. |
| P045600 | - | A very fine leak in the evaporative emission control system was detected. |
| P045609 | - | A very fine leak in the evaporative emission control system was detected. There is a component fault. |
| P04567A | - | A very fine leak in the evaporative emission control system was detected. Leakage or a defective seal was detected. |
| P045709 | - | Leakage in the evaporative emission control system was detected (tank cap missing). There is a component fault. |
| P04577A | - | Leakage in the evaporative emission control system was detected (tank cap missing). Leakage or a defective seal was detected. |
| P045800 | - | The purge valve of the evaporative emission control system has a short circuit to ground. |
| P045900 | - | The purge valve of the evaporative emission control system has a short circuit to positive. |
| P046100 | - | The fill level sensor 'Fuel' on the left has malfunction. |
| P046109 | - | The fill level sensor 'Fuel' on the left has malfunction. There is a component fault. |
| P046200 | - | The fill level sensor 'Fuel' on the left has a short circuit to ground. |
| P046300 | - | The fill level sensor 'Fuel' on the left has a short circuit to positive. |
| P048300 | - | The electric fan has a malfunction. |
| P049600 | - | The purge flow of the evaporative emission control system is too high. |
| P049700 | - | The purge flow of the evaporative emission control system is too low. |
| P049800 | - | The shutoff valve of the activated charcoal canister has a short circuit to ground. |
| P049900 | - | The shutoff valve of the activated charcoal canister has a short circuit to positive. |
| P04F000 | - | Wide open throttle regeneration of the activated charcoal canister has a malfunction. |
| P050000 | - | Speed sensor 1 has an electrical fault. |
| P050001 | - | Speed sensor 1 has an electrical fault. There is a general electrical fault. |
| P050400 | - | The signals from the switch 'Brake light' are implausible in relation to each other. |
| P050500 | - | The idle speed control has a malfunction. |
| P050600 | - | Idle speed is too low when engine is warm. |
| P050700 | - | Idle speed is too high when engine is warm. |
| P050A84 | - | Idle speed control has a malfunction during a cold start. There is a signal below the permissible limit value. |
| P050A85 | - | Idle speed control has a malfunction during a cold start. There is a signal above the permissible limit value. |
| P050A92 | - | Idle speed control has a malfunction during a cold start. The function or the instruction is faulty. |
| P050A94 | - | Idle speed control has a malfunction during a cold start. There is an unexpected instruction. |
| P050B00 | - | The ignition angle setting has a malfunction when cold starting. |
| P050B04 | - | The ignition angle setting has a malfunction when cold starting. There is an internal fault. |
| P050B62 | - | The ignition angle setting has a malfunction when cold starting. The signal comparison is faulty. |
| P050B64 | - | The ignition angle setting has a malfunction when cold starting. There is an implausible signal. |
| P050D00 | - | The combustion engine idles roughly after a cold start. |
| P050D64 | - | The combustion engine idles roughly after a cold start. There is an implausible signal. |
| P051200 | - | The start enable has a malfunction. |
| P051296 | - | The start enable has a malfunction. There is an internal component fault. |
| P051297 | - | The start enable has a malfunction. The system function is restricted. |
| P051301 | - | The start enable was not issued. There is a general electrical fault. |
| P051302 | - | The start enable was not issued. There is a general signal fault. |
| P051303 | - | The start enable was not issued. There is a frequency or pulse width modulation fault. |
| P051304 | - | The start enable was not issued. There is an internal fault. |
| P051305 | - | The start enable was not issued. There is a programming fault. |
| P051306 | - | The start enable was not issued. There is an algorithm fault. |
| P051307 | - | The start enable was not issued. There is a mechanical fault. |
| P051308 | - | The start enable was not issued. There is a signal fault or the message is faulty. |
| P051309 | - | The start enable was not issued. There is a component fault. |
| P051310 | - | The start enable was not issued. Reserved for ISO/SAE |
| P051311 | - | The start enable was not issued. There is a short circuit to ground. |
| P051312 | - | The start enable was not issued. There is a short circuit to positive. |
| P051313 | - | The start enable was not issued. There is an open circuit. |
| P051314 | - | The start enable was not issued. There is a short circuit to ground or an open circuit. |
| P051315 | - | The start enable was not issued. There is a short circuit to positive or an open circuit. |
| P051316 | - | The start enable was not issued. The limit value for electrical voltage has not been attained. |
| P051B28 | - | The differential pressure sensor 'Crankcase ventilation system' has a malfunction. The signal offset is outside the permissible range. |
| P051B2A | - | The differential pressure sensor 'Crankcase ventilation system' has a malfunction. There is no signal change. |
| P051B49 | - | The differential pressure sensor 'Crankcase ventilation system' has a malfunction. There is an internal electrical fault. |
| P051B84 | - | The differential pressure sensor 'Crankcase ventilation system' has a malfunction. There is a signal below the permissible limit value. |
| P051B85 | - | The differential pressure sensor 'Crankcase ventilation system' has a malfunction. There is a signal above the permissible limit value. |
| P051C11 | - | The differential pressure sensor 'Crankcase ventilation system' has a short circuit to ground. There is a short circuit to ground. |
| P051D15 | - | The differential pressure sensor 'Crankcase ventilation system' has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P051E27 | - | Differential pressure sensor ""Crankcase ventilation system"" has a sporadic malfunction. The signal change rate is above the permissible limit value. |
| P052100 | - | The engine oil pressure sensor has a malfunction. |
| P052121 | - | The engine oil pressure sensor has a malfunction. The signal amplitude is less than the minimum amplitude. |
| P052122 | - | The engine oil pressure sensor has a malfunction. The signal amplitude is greater than the maximum amplitude. |
| P052127 | - | The engine oil pressure sensor has a malfunction. The signal change rate is above the permissible limit value. |
| P052128 | - | The engine oil pressure sensor has a malfunction. The signal offset is outside the permissible range. |
| P05212A | - | The engine oil pressure sensor has a malfunction. There is no signal change. |
| P052149 | - | The engine oil pressure sensor has a malfunction. There is an internal electrical fault. |
| P052164 | - | The engine oil pressure sensor has a malfunction. There is an implausible signal. |
| P052200 | - | The engine oil pressure sensor has a short circuit to ground. |
| P052300 | - | The engine oil pressure sensor has a short circuit to positive. |
| P052A00 | - | The position of the intake camshaft (cylinder bank 1) deviates from the specified value in direction ""Advanced"" during cold start. |
| P052A64 | - | The position of the intake camshaft (cylinder bank 1) deviates from the specified value in direction ""Advanced"" during cold start. There is an implausible signal. |
| P053F92 | - | The fuel pressure during a cold start is implausible. The function or the instruction is faulty. |
| P053F94 | - | The fuel pressure during a cold start is implausible. There is an unexpected instruction. |
| P054449 | - | Temperature sensor 1 'Exhaust system' (cylinder bank 1) has an electrical fault. There is an internal electrical fault. |
| P054500 | - | Temperature sensor 1 'Exhaust system' (cylinder bank 1) has a short circuit to ground. |
| P054511 | - | Temperature sensor 1 'Exhaust system' (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground. |
| P054521 | - | Temperature sensor 1 'Exhaust system' (cylinder bank 1) has a short circuit to ground. The signal amplitude is less than the minimum amplitude. |
| P054600 | - | Temperature sensor 1 'Exhaust system' (cylinder bank 1) has a short circuit to positive. |
| P054612 | - | Temperature sensor 1 'Exhaust system' (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive. |
| P054615 | - | Temperature sensor 1 'Exhaust system' (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P054622 | - | Temperature sensor 1 'Exhaust system' (cylinder bank 1) has a short circuit to positive. The signal amplitude is greater than the maximum amplitude. |
| P054A00 | - | The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value in direction 'Advanced' during cold start. |
| P054A64 | - | The position of the exhaust camshaft (cylinder bank 1) deviates from the specified value in direction 'Advanced' during cold start. There is an implausible signal. |
| P055F28 | - | The oil pressure in the combustion engine is outside the permissible range. The signal offset is outside the permissible range. |
| P055F84 | - | The oil pressure in the combustion engine is outside the permissible range. There is a signal below the permissible limit value. |
| P055F85 | - | The oil pressure in the combustion engine is outside the permissible range. There is a signal above the permissible limit value. |
| P056000 | - | The on-board electrical system voltage has a malfunction. |
| P056013 | - | The on-board electrical system voltage has a malfunction. There is an open circuit. |
| P056061 | - | The on-board electrical system voltage has a malfunction. The signal calculation is faulty. |
| P056062 | - | The on-board electrical system voltage has a malfunction. The signal comparison is faulty. |
| P056111 | - | The on-board power supply voltage is too low. There is a short circuit to ground. |
| P056114 | - | The on-board power supply voltage is too low. There is a short circuit to ground or an open circuit. |
| P056116 | - | The on-board electrical system voltage is unstable. The limit value for electrical voltage has not been attained. |
| P056121 | - | The on-board electrical system voltage is unstable. The signal amplitude is less than the minimum amplitude. |
| P056200 | - | The on-board power supply voltage is too low. |
| P056201 | - | The on-board power supply voltage is too low. There is a general electrical fault. |
| P056211 | - | The on-board power supply voltage is too low. There is a short circuit to ground. |
| P056214 | - | The on-board power supply voltage is too low. There is a short circuit to ground or an open circuit. |
| P056216 | - | The on-board power supply voltage is too low. The limit value for electrical voltage has not been attained. |
| P056221 | - | The on-board power supply voltage is too low. The signal amplitude is less than the minimum amplitude. |
| P056300 | - | The on-board power supply voltage is too high. |
| P056312 | - | The on-board power supply voltage is too high. There is a short circuit to positive. |
| P056315 | - | The on-board power supply voltage is too high. There is a short circuit to positive or an open circuit. |
| P056317 | - | The on-board power supply voltage is too high. The limit value for electrical voltage has been exceeded. |
| P056322 | - | The on-board power supply voltage is too high. The signal amplitude is greater than the maximum amplitude. |
| P057129 | - | The switch 'Brake light' has a malfunction. There is an invalid signal. |
| P059700 | - | The coolant thermostat has an electrical fault or open circuit. |
| P059800 | - | The coolant thermostat has a short circuit to ground. |
| P059900 | - | The coolant thermostat has a short circuit to positive. |
| P059F00 | - | Radiator shutter 1 does not close. |
| P060100 | - | There is an internal control unit fault affecting the calculation of the checksum. |
| P060400 | - | There is an internal control unit fault in the RAM memory. |
| P060600 | - | There is an internal control unit fault in the processor. |
| P060601 | - | There is an internal control unit fault in the processor. There is a general electrical fault. |
| P060602 | - | There is an internal control unit fault in the processor. There is a general signal fault. |
| P060603 | - | There is an internal control unit fault in the processor. There is a frequency or pulse width modulation fault. |
| P060604 | - | There is an internal control unit fault in the processor. There is an internal fault. |
| P060605 | - | There is an internal control unit fault in the processor. There is a programming fault. |
| P060606 | - | There is an internal control unit fault in the processor. There is an algorithm fault. |
| P060607 | - | There is an internal control unit fault in the processor. There is a mechanical fault. |
| P060608 | - | There is an internal control unit fault in the processor. There is a signal fault or the message is faulty. |
| P060609 | - | There is an internal control unit fault in the processor. There is a component fault. |
| P060611 | - | There is an internal control unit fault in the processor. There is a short circuit to ground. |
| P060612 | - | There is an internal control unit fault in the processor. There is a short circuit to positive. |
| P060613 | - | There is an internal control unit fault in the processor. There is an open circuit. |
| P060614 | - | There is an internal control unit fault in the processor. There is a short circuit to ground or an open circuit. |
| P060615 | - | There is an internal control unit fault in the processor. There is a short circuit to positive or an open circuit. |
| P060616 | - | There is an internal control unit fault in the processor. The limit value for electrical voltage has not been attained. |
| P060617 | - | There is an internal control unit fault in the processor. The limit value for electrical voltage has been exceeded. |
| P060618 | - | There is an internal control unit fault in the processor. The limit value for current has not been attained. |
| P060619 | - | There is an internal control unit fault in the processor. The limit value for current has been exceeded. |
| P06061A | - | There is an internal control unit fault in the processor. The limit value for resistance has not been attained. |
| P06061B | - | There is an internal control unit fault in the processor. The limit value for resistance has been exceeded. |
| P06061C | - | There is an internal control unit fault in the processor. The voltage value is outside the permissible range. |
| P06061D | - | There is an internal control unit fault in the processor. The current value is outside the permissible range. |
| P06061E | - | There is an internal control unit fault in the processor. The resistance value is outside the permissible range. |
| P06061F | - | There is an internal control unit fault in the processor. There is a sporadic fault. |
| P060621 | - | There is an internal control unit fault in the processor. The signal amplitude is less than the minimum amplitude. |
| P060622 | - | There is an internal control unit fault in the processor. The signal amplitude is greater than the maximum amplitude. |
| P060623 | - | There is an internal control unit fault in the processor. No signal change: Voltage level is too low. |
| P060624 | - | There is an internal control unit fault in the processor. No signal change: Voltage level is too high. |
| P060625 | - | There is an internal control unit fault in the processor. There is a faulty signal waveform. |
| P060626 | - | There is an internal control unit fault in the processor. The signal change rate is below the permissible limit value. |
| P060627 | - | There is an internal control unit fault in the processor. The signal change rate is above the permissible limit value. |
| P060628 | - | There is an internal control unit fault in the processor. The signal offset is outside the permissible range. |
| P060629 | - | There is an internal control unit fault in the processor. There is an invalid signal. |
| P06062A | - | There is an internal control unit fault in the processor. There is no signal change. |
| P06062B | - | There is an internal control unit fault in the processor. The electrical lines have a short circuit to each other. |
| P06062F | - | There is an internal control unit fault in the processor. There is an erratic signal. |
| P060631 | - | There is an internal control unit fault in the processor. The signal is not present. |
| P060632 | - | There is an internal control unit fault in the processor. The off-time of the signal frequency is too short. |
| P060633 | - | There is an internal control unit fault in the processor. The off-time of the signal frequency is too long. |
| P060634 | - | There is an internal control unit fault in the processor. The on-time of the signal frequency is too short. |
| P060635 | - | There is an internal control unit fault in the processor. The on-time of the signal frequency is too long. |
| P060636 | - | There is an internal control unit fault in the processor. The signal frequency is too low. |
| P060637 | - | There is an internal control unit fault in the processor. The signal frequency is too high. |
| P060638 | - | There is an internal control unit fault in the processor. There is an incorrect signal frequency. |
| P060639 | - | There is an internal control unit fault in the processor. The signal has too few pulses. |
| P06063A | - | There is an internal control unit fault in the processor. The signal has too many pulses. |
| P060641 | - | There is an internal control unit fault in the processor. There is a general checksum error. |
| P060642 | - | There is an internal control unit fault in the processor. There is a general memory error. |
| P060643 | - | There is an internal control unit fault in the processor. There is an error in the additional memory. |
| P060644 | - | There is an internal control unit fault in the processor. There is an error in the data memory. |
| P060645 | - | There is an internal control unit fault in the processor. There is an error in the program memory. |
| P060646 | - | There is an internal control unit fault in the processor. There is an error in the calibration or parameterization memory. |
| P060647 | - | There is an internal control unit fault in the processor. There is a runtime error. |
| P060648 | - | There is an internal control unit fault in the processor. There is an error in the control memory. |
| P060649 | - | There is an internal control unit fault in the processor. There is an internal electrical fault. |
| P06064A | - | There is an internal control unit fault in the processor. The wrong component is installed. |
| P06064B | - | There is an internal control unit fault in the processor. There is a fault due to overtemperature. |
| P060651 | - | There is an internal control unit fault in the processor. The component is not programmed. |
| P060652 | - | There is an internal control unit fault in the processor. The component has not been put into operation. |
| P060653 | - | There is an internal control unit fault in the processor. The component is deactivated. |
| P060654 | - | There is an internal control unit fault in the processor. Calibration is missing. |
| P060655 | - | There is an internal control unit fault in the processor. The component is not configured. |
| P060656 | - | There is an internal control unit fault in the processor. An incorrect or incompatible configuration was detected. |
| P060657 | - | There is an internal control unit fault in the processor. Incorrect or incompatible software modules were detected. |
| P060661 | - | There is an internal control unit fault in the processor. The signal calculation is faulty. |
| P060662 | - | There is an internal control unit fault in the processor. The signal comparison is faulty. |
| P060663 | - | There is an internal control unit fault in the processor. The duration of the actuation was exceeded: overload protection is active. |
| P060664 | - | There is an internal control unit fault in the processor. There is an implausible signal. |
| P060665 | - | There is an internal control unit fault in the processor. The signal has too few transitions or events. |
| P060666 | - | There is an internal control unit fault in the processor. The signal has too many transitions or events. |
| P060667 | - | There is an internal control unit fault in the processor. The signal is impermissible after an event. |
| P060668 | - | There is an internal control unit fault in the processor. There is incomplete information. |
| P060671 | - | There is an internal control unit fault in the processor. The actuator is blocked. |
| P060672 | - | There is an internal control unit fault in the processor. The actuator does not close. |
| P060673 | - | There is an internal control unit fault in the processor. The actuator does not open. |
| P060674 | - | There is an internal control unit fault in the processor. The actuator slips. |
| P060675 | - | There is an internal control unit fault in the processor. The emergency position was not reached. |
| P060676 | - | There is an internal control unit fault in the processor. The assembly position is incorrect. |
| P060677 | - | There is an internal control unit fault in the processor. The commanded position cannot be reached. |
| P060678 | - | There is an internal control unit fault in the processor. The adaptation or adjustment is incorrect. |
| P060679 | - | There is an internal control unit fault in the processor. The mechanical connection has failed. |
| P06067A | - | There is an internal control unit fault in the processor. Leakage or a defective seal was detected. |
| P06067B | - | There is an internal control unit fault in the processor. The fluid level is too low. |
| P060681 | - | There is an internal control unit fault in the processor. Incorrect data were received. |
| P060682 | - | There is an internal control unit fault in the processor. The instruction counter is not updated. |
| P060683 | - | There is an internal control unit fault in the processor. The checksum for the message has an incorrect value. |
| P060684 | - | There is an internal control unit fault in the processor. There is a signal below the permissible limit value. |
| P060685 | - | There is an internal control unit fault in the processor. There is a signal above the permissible limit value. |
| P060686 | - | There is an internal control unit fault in the processor. There is an incorrect signal. |
| P060687 | - | There is an internal control unit fault in the processor. The message is missing. |
| P060688 | - | There is an internal control unit fault in the processor. Bus OFF |
| P06068F | - | There is an internal control unit fault in the processor. The signal or message is erratic. |
| P0606E0 | - | There is an internal control unit fault in the processor. |
| P0606E6 | - | There is an internal control unit fault in the processor. |
| P0606E9 | - | There is an internal control unit fault in the processor. |
| P0606EA | - | There is an internal control unit fault in the processor. |
| P0606ED | - | There is an internal control unit fault in the processor. |
| P0606EE | - | There is an internal control unit fault in the processor. |
| P0606FA | - | There is an internal control unit fault in the processor. |
| P0606FB | - | There is an internal control unit fault in the processor. |
| P0606FC | - | There is an internal control unit fault in the processor. |
| P0606FD | - | There is an internal control unit fault in the processor. |
| P0606FF | - | There is an internal control unit fault in the processor. |
| P060700 | - | The control unit has a malfunction. |
| P060701 | - | The control unit has a malfunction. There is a general electrical fault. |
| P060702 | - | The control unit has a malfunction. There is a general signal fault. |
| P060703 | - | The control unit has a malfunction. There is a frequency or pulse width modulation fault. |
| P060704 | - | The control unit has a malfunction. There is an internal fault. |
| P060705 | - | The control unit has a malfunction. There is a programming fault. |
| P060706 | - | The control unit has a malfunction. There is an algorithm fault. |
| P060707 | - | The control unit has a malfunction. There is a mechanical fault. |
| P060708 | - | The control unit has a malfunction. There is a signal fault or the message is faulty. |
| P060709 | - | The control unit has a malfunction. There is a component fault. |
| P060710 | - | The control unit has a malfunction. Reserved for ISO/SAE |
| P060711 | - | The control unit has a malfunction. There is a short circuit to ground. |
| P060712 | - | The control unit has a malfunction. There is a short circuit to positive. |
| P060713 | - | The control unit has a malfunction. There is an open circuit. |
| P060714 | - | The control unit has a malfunction. There is a short circuit to ground or an open circuit. |
| P060715 | - | The control unit has a malfunction. There is a short circuit to positive or an open circuit. |
| P060716 | - | The control unit has a malfunction. The limit value for electrical voltage has not been attained. |
| P060717 | - | The control unit has a malfunction. The limit value for electrical voltage has been exceeded. |
| P060718 | - | The control unit has a malfunction. The limit value for current has not been attained. |
| P060719 | - | The control unit has a malfunction. The limit value for current has been exceeded. |
| P06071A | - | The control unit has a malfunction. The limit value for resistance has not been attained. |
| P06071B | - | The control unit has a malfunction. The limit value for resistance has been exceeded. |
| P06071C | - | The control unit has a malfunction. The voltage value is outside the permissible range. |
| P06071D | - | The control unit has a malfunction. The current value is outside the permissible range. |
| P060744 | - | The control unit has a malfunction. There is an error in the data memory. |
| P06074B | - | The control unit has a malfunction. There is a fault due to overtemperature. |
| P060754 | - | The control unit has a malfunction. Calibration is missing. |
| P060755 | - | The control unit has a malfunction. The component is not configured. |
| P060781 | - | The control unit has a malfunction. Incorrect data were received. |
| P060787 | - | The control unit has a malfunction. The message is missing. |
| P060788 | - | The control unit has a malfunction. Bus OFF |
| P060A00 | - | The monitoring function in the control unit has a malfunction. |
| P060B00 | - | There is an internal control unit fault in the analog/digital converter. |
| P060C00 | - | There is an internal control unit fault in the central processing unit. |
| P060C01 | - | There is an internal control unit fault in the central processing unit. There is a general electrical fault. |
| P060C02 | - | There is an internal control unit fault in the central processing unit. There is a general signal fault. |
| P060C04 | - | There is an internal control unit fault in the central processing unit. There is an internal fault. |
| P060C08 | - | There is an internal control unit fault in the central processing unit. There is a signal fault or the message is faulty. |
| P060C17 | - | There is an internal control unit fault in the central processing unit. The limit value for electrical voltage has been exceeded. |
| P060C29 | - | There is an internal control unit fault in the central processing unit. There is an invalid signal. |
| P060C47 | - | There is an internal control unit fault in the central processing unit. There is a runtime error. |
| P060C61 | - | There is an internal control unit fault in the central processing unit. The signal calculation is faulty. |
| P060C64 | - | There is an internal control unit fault in the central processing unit. There is an implausible signal. |
| P061000 | - | The coding of the control unit is incorrect. |
| P061001 | - | The coding of the control unit is incorrect. There is a general electrical fault. |
| P061002 | - | The coding of the control unit is incorrect. There is a general signal fault. |
| P061004 | - | The coding of the control unit is incorrect. There is an internal fault. |
| P0610FA | - | The coding of the control unit is incorrect. |
| P061100 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). |
| P061102 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a general signal fault. |
| P061103 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a frequency or pulse width modulation fault. |
| P061104 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is an internal fault. |
| P061105 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a programming fault. |
| P061106 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is an algorithm fault. |
| P061107 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a mechanical fault. |
| P061108 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a signal fault or the message is faulty. |
| P061113 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is an open circuit. |
| P061116 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The limit value for electrical voltage has not been attained. |
| P061117 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The limit value for electrical voltage has been exceeded. |
| P061121 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The signal amplitude is less than the minimum amplitude. |
| P061122 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The signal amplitude is greater than the maximum amplitude. |
| P061123 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). No signal change: Voltage level is too low. |
| P061124 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). No signal change: Voltage level is too high. |
| P061125 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a faulty signal waveform. |
| P061126 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The signal change rate is below the permissible limit value. |
| P061142 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is a general memory error. |
| P061149 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is an internal electrical fault. |
| P06114A | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The wrong component is installed. |
| P061165 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The signal has too few transitions or events. |
| P061167 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The signal is impermissible after an event. |
| P061188 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). Bus OFF |
| P061192 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The function or the instruction is faulty. |
| P061194 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is an unexpected instruction. |
| P061196 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). There is an internal component fault. |
| P061197 | - | The control unit 'fuel injector' has a malfunction (output stage fault of control unit 'combustion engine'). The system function is restricted. |
| P061513 | - | The electrical line A of the starter relay has an electrical fault. There is an open circuit. |
| P061605 | - | The electrical line A of the starter relay has a short circuit to ground. There is a programming fault. |
| P061606 | - | The electrical line A of the starter relay has a short circuit to ground. There is an algorithm fault. |
| P061614 | - | The electrical line A of the starter relay has a short circuit to ground. There is a short circuit to ground or an open circuit. |
| P061703 | - | The electrical line A of the starter relay has a short circuit to positive. There is a frequency or pulse width modulation fault. |
| P061704 | - | The electrical line A of the starter relay has a short circuit to positive. There is an internal fault. |
| P061715 | - | The electrical line A of the starter relay has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P061A00 | - | The torque control of the control unit has a malfunction. |
| P061A28 | - | The torque control of the control unit has a malfunction. The signal offset is outside the permissible range. |
| P061B00 | - | The torque calculation of the control unit has a malfunction. |
| P061B01 | - | The torque calculation of the control unit has a malfunction. There is a general electrical fault. |
| P061B02 | - | The torque calculation of the control unit has a malfunction. There is a general signal fault. |
| P061B04 | - | The torque calculation of the control unit has a malfunction. There is an internal fault. |
| P061B05 | - | The torque calculation of the control unit has a malfunction. There is a programming fault. |
| P061B06 | - | The torque calculation of the control unit has a malfunction. There is an algorithm fault. |
| P061B08 | - | The torque calculation of the control unit has a malfunction. There is a signal fault or the message is faulty. |
| P061B64 | - | The torque calculation of the control unit has a malfunction. There is an implausible signal. |
| P061B84 | - | The torque calculation of the control unit has a malfunction. There is a signal below the permissible limit value. |
| P061B85 | - | The torque calculation of the control unit has a malfunction. There is a signal above the permissible limit value. |
| P061B86 | - | The torque calculation of the control unit has a malfunction. There is an incorrect signal. |
| P061B91 | - | The torque calculation of the control unit has a malfunction. The parameter is outside the permissible range. |
| P061C00 | - | There is an internal control unit fault affecting the calculation of the engine speed. |
| P061C02 | - | There is an internal control unit fault affecting the calculation of the engine speed. There is a general signal fault. |
| P061C04 | - | There is an internal control unit fault affecting the calculation of the engine speed. There is an internal fault. |
| P061C64 | - | There is an internal control unit fault affecting the calculation of the engine speed. There is an implausible signal. |
| P061D00 | - | There is an internal control unit fault in the monitoring function for the air mass. |
| P062700 | - | The output for the fuel pump has an electrical fault or open circuit. |
| P062713 | - | The output for the fuel pump has an electrical fault or open circuit. There is an open circuit. |
| P062800 | - | The output for the fuel pump has a short circuit to ground. |
| P062811 | - | The output for the fuel pump has a short circuit to ground. There is a short circuit to ground. |
| P062900 | - | The output for the fuel pump has a short circuit to positive. |
| P062912 | - | The output for the fuel pump has a short circuit to positive. There is a short circuit to positive. |
| P062B00 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. |
| P062B01 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. There is a general electrical fault. |
| P062B02 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. There is a general signal fault. |
| P062B03 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. There is a frequency or pulse width modulation fault. |
| P062B04 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. There is an internal fault. |
| P062B62 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. The signal comparison is faulty. |
| P062B63 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. The duration of the actuation was exceeded: overload protection is active. |
| P062B64 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. There is an implausible signal. |
| P062B66 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. The signal has too many transitions or events. |
| P062B68 | - | There is an internal control unit fault in the monitoring function for the fuel injectors. There is incomplete information. |
| P063300 | - | The control unit is not personalized. |
| P063344 | - | The control unit is not personalized. There is an error in the data memory. |
| P063800 | - | The output for the throttle valve actuator (cylinder bank 1) has a malfunction. |
| P063E00 | - | The throttle valve adaptation has a malfunction. |
| P063E04 | - | The throttle valve adaptation has a malfunction. There is an internal fault. |
| P064200 | - | Output 1 for the reference voltage of the sensors has a short circuit to ground. |
| P064211 | - | Output 1 for the reference voltage of the sensors has a short circuit to ground. There is a short circuit to ground. |
| P064300 | - | Output 1 for the reference voltage of the sensors has a short circuit to positive. |
| P064A00 | - | Control unit 'Fuel pump' has a malfunction. |
| P064D00 | - | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. |
| P064D04 | - | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. There is an internal fault. |
| P064D64 | - | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. There is an implausible signal. |
| P064D86 | - | The processor of the oxygen sensor (cylinder bank 1) in the control unit has a malfunction. There is an incorrect signal. |
| P065200 | - | Output 2 for the reference voltage of the sensors has a short circuit to ground. |
| P065211 | - | Output 2 for the reference voltage of the sensors has a short circuit to ground. There is a short circuit to ground. |
| P065300 | - | Output 2 for the reference voltage of the sensors has a short circuit to positive. |
| P065400 | - | The output signal for engine speed has an electrical fault or open circuit. |
| P065413 | - | The output signal for engine speed has an electrical fault or open circuit. There is an open circuit. |
| P065700 | - | The power supply of the actuators has an electrical fault or an open circuit. |
| P06574B | - | The power supply of the actuators has an electrical fault or an open circuit. There is a fault due to overtemperature. |
| P065800 | - | The power supply to the actuators has a short circuit to ground. |
| P065900 | - | The power supply to the actuators has a short circuit to positive. |
| P065B04 | - | The alternator has a malfunction. There is an internal fault. |
| P065B16 | - | The alternator has a malfunction. The limit value for electrical voltage has not been attained. |
| P065B17 | - | The alternator has a malfunction. The limit value for electrical voltage has been exceeded. |
| P065C00 | - | The alternator has a mechanical malfunction. |
| P066716 | - | The internal temperature sensor of the control unit has a malfunction. The limit value for electrical voltage has not been attained. |
| P066717 | - | The internal temperature sensor of the control unit has a malfunction. The limit value for electrical voltage has been exceeded. |
| P066729 | - | The internal temperature sensor of the control unit has a malfunction. There is an invalid signal. |
| P066900 | - | The internal temperature sensor of the control unit has a short circuit to positive. |
| P069800 | - | Output 3 for the reference voltage of the sensors has a short circuit to ground. |
| P069811 | - | Output 3 for the reference voltage of the sensors has a short circuit to ground. There is a short circuit to ground. |
| P069900 | - | Output 3 for the reference voltage of the sensors has a short circuit to positive. |
| P06A300 | - | Output 4 for the reference voltage of the sensors has an electrical fault or an open circuit. |
| P06A600 | - | Output 1 for the reference voltage of the sensors has a malfunction. |
| P06A700 | - | Output 2 for the reference voltage of the sensors has a malfunction. |
| P06A800 | - | Output 3 for the reference voltage of the sensors has a malfunction. |
| P06B000 | - | Output 1 for the power supply of the sensors has an electrical fault or an open circuit. |
| P06B100 | - | Output 1 for the power supply of the sensors has a short circuit to ground. |
| P06B200 | - | Output 1 for the power supply of the sensors has a short circuit to positive. |
| P06B300 | - | Output 2 for the power supply of the sensors has an electrical fault or an open circuit. |
| P06B400 | - | Output 2 for the power supply of the sensors has a short circuit to ground. |
| P06D100 | - | Control unit 'Combustion engine' has detected an internal fault on the output stage of the ignition coil. |
| P06D200 | - | Output 5 for the reference voltage of the sensors has an electrical fault or an open circuit. |
| P06DA00 | - | The actuation of the valve of the oil pump in the combustion engine has an electrical fault or open circuit. |
| P06DA13 | - | The actuation of the valve of the oil pump in the combustion engine has an electrical fault or open circuit. There is an open circuit. |
| P06DA2B | - | The actuation of the valve of the oil pump in the combustion engine has an electrical fault or open circuit. The electrical lines have a short circuit to each other. |
| P06DB00 | - | The actuation of the valve of the oil pump in the combustion engine has a short circuit to ground. |
| P06DB11 | - | The actuation of the valve of the oil pump in the combustion engine has a short circuit to ground. There is a short circuit to ground. |
| P06DC00 | - | The actuation of the valve of the oil pump in the combustion engine has a short circuit to positive. |
| P06DC12 | - | The actuation of the valve of the oil pump in the combustion engine has a short circuit to positive. There is a short circuit to positive. |
| P06DD1D | - | The valve of the oil pump in the combustion engine does not close. The current value is outside the permissible range. |
| P06DD4B | - | The valve of the oil pump in the combustion engine does not close. There is a fault due to overtemperature. |
| P06E900 | - | The starter of the combustion engine has a malfunction. |
| P06E901 | - | The starter of the combustion engine has a malfunction. There is a general electrical fault. |
| P06E997 | - | The starter of the combustion engine has a malfunction. The system function is restricted. |
| P06ED00 | - | The output signal for engine speed has a short circuit to ground. |
| P06ED11 | - | The output signal for engine speed has a short circuit to ground. There is a short circuit to ground. |
| P06EE00 | - | The output signal for engine speed has a short circuit to positive. |
| P06EE12 | - | The output signal for engine speed has a short circuit to positive. There is a short circuit to positive. |
| P0A0F00 | - | The engine does not start. |
| P0A0F01 | - | The engine does not start. There is a general electrical fault. |
| P0D1F08 | - | The synchronization of the operating hours counter has a malfunction. There is a signal fault or the message is faulty. |
| P0D1F84 | - | The synchronization of the operating hours counter has a malfunction. There is a signal below the permissible limit value. |
| P0D1F85 | - | The synchronization of the operating hours counter has a malfunction. There is a signal above the permissible limit value. |
| P13C200 | - | The exhaust flap has a malfunction. |
| P13C500 | - | A short-term torque limitation was detected by the knock control. |
| P13C600 | - | A long-term torque limitation was detected by the knock control. |
| P13EA64 | - | The ignition angle setting has a malfunction during cold starting (partial load operation). There is an implausible signal. |
| P140400 | - | Exhaust flap 2 has a malfunction. |
| P144F00 | - | The tank cap is defective due to excessive vacuum in the fuel tank. |
| P145000 | - | The shutoff valve in the evaporative emission control system is defective. |
| P145009 | - | The shutoff valve in the evaporative emission control system is defective. There is a component fault. |
| P145100 | - | The vent valves in the fuel tank are closed. |
| P145200 | - | The fuel filler flap cannot be opened due to excessive pressure in the fuel tank. |
| P146200 | - | The sensor 'Low fuel pressure and fuel temperature' has a malfunction. |
| P146264 | - | The sensor 'Low fuel pressure and fuel temperature' has a malfunction. There is an implausible signal. |
| P146300 | - | This error code can be ignored and erased. |
| P146364 | - | This error code can be ignored and erased. |
| P147000 | - | This error code can be ignored and erased. |
| P147011 | - | This error code can be ignored and erased. |
| P147100 | - | This error code can be ignored and erased. |
| P147112 | - | This error code can be ignored and erased. |
| P152200 | - | The check valve of the evaporative emission control system (at partial load) is jammed closed. |
| P152300 | - | The check valve of the evaporative emission control system (at partial load) is jammed open. |
| P152400 | - | The check valve of the evaporative emission control system (at full load) is jammed closed. |
| P152500 | - | The check valve of the evaporative emission control system (at full load) is jammed open. |
| P161200 | - | The fuel pump was deactivated because of a crash signal. |
| P161297 | - | The fuel pump was deactivated because of a crash signal. The system function is restricted. |
| P161400 | - | An internal control unit reset was performed. |
| P161401 | - | An internal control unit reset was performed. There is a general electrical fault. |
| P161404 | - | An internal control unit reset was performed. There is an internal fault. |
| P161405 | - | An internal control unit reset was performed. There is a programming fault. |
| P161406 | - | An internal control unit reset was performed. There is an algorithm fault. |
| P161496 | - | An internal control unit reset was performed. There is an internal component fault. |
| P164405 | - | An incorrect variant coding or configuration was detected. There is a programming fault. |
| P164456 | - | An incorrect variant coding or configuration was detected. An incorrect or incompatible configuration was detected. |
| P164B00 | - | System 'CAMTRONIC' is in limp-home mode. |
| P164B07 | - | System 'CAMTRONIC' is in limp-home mode. There is a mechanical fault. |
| P164B09 | - | System 'CAMTRONIC' is in limp-home mode. There is a component fault. |
| P167000 | - | Calibration of the torque curve of the control unit has a malfunction. |
| P167085 | - | Calibration of the torque curve of the control unit has a malfunction. There is a signal above the permissible limit value. |
| P176421 | - | The pressure sensor upstream of the electric additional compressor has a malfunction. The signal amplitude is less than the minimum amplitude. |
| P176422 | - | The pressure sensor upstream of the electric additional compressor has a malfunction. The signal amplitude is greater than the maximum amplitude. |
| P176427 | - | The pressure sensor upstream of the electric additional compressor has a malfunction. The signal change rate is above the permissible limit value. |
| P176428 | - | The pressure sensor upstream of the electric additional compressor has a malfunction. The signal offset is outside the permissible range. |
| P17642A | - | The pressure sensor upstream of the electric additional compressor has a malfunction. There is no signal change. |
| P176449 | - | The pressure sensor upstream of the electric additional compressor has a malfunction. There is an internal electrical fault. |
| P176484 | - | The pressure sensor upstream of the electric additional compressor has a malfunction. There is a signal below the permissible limit value. |
| P176485 | - | The pressure sensor upstream of the electric additional compressor has a malfunction. There is a signal above the permissible limit value. |
| P176A21 | - | The temperature sensor upstream of the electric additional compressor has a malfunction. The signal amplitude is less than the minimum amplitude. |
| P176A22 | - | The temperature sensor upstream of the electric additional compressor has a malfunction. The signal amplitude is greater than the maximum amplitude. |
| P176A28 | - | The temperature sensor upstream of the electric additional compressor has a malfunction. The signal offset is outside the permissible range. |
| P176A2A | - | The temperature sensor upstream of the electric additional compressor has a malfunction. There is no signal change. |
| P176A49 | - | The temperature sensor upstream of the electric additional compressor has a malfunction. There is an internal electrical fault. |
| P176A84 | - | The temperature sensor upstream of the electric additional compressor has a malfunction. There is a signal below the permissible limit value. |
| P176A85 | - | The temperature sensor upstream of the electric additional compressor has a malfunction. There is a signal above the permissible limit value. |
| P199900 | - | This error code can be ignored and erased. |
| P199903 | - | Unknown fault code. There is a frequency or pulse width modulation fault. |
| P199904 | - | Unknown fault code. There is an internal fault. |
| P199905 | - | Unknown fault code. There is a programming fault. |
| P199906 | - | Unknown fault code. There is an algorithm fault. |
| P199908 | - | This error code can be ignored and erased. |
| P1B9200 | - | The connection of the alternator (circuit 30/31) has an open circuit. |
| P1B9416 | - | Pressure sensor/pressure switch 2 of evaporative emission control system 2 has a malfunction. The limit value for electrical voltage has not been attained. |
| P1B9417 | - | Pressure sensor/pressure switch 2 of evaporative emission control system 2 has a malfunction. The limit value for electrical voltage has been exceeded. |
| P1B9426 | - | Pressure sensor/pressure switch 2 of evaporative emission control system 2 has a malfunction. The signal change rate is below the permissible limit value. |
| P1B9428 | - | Pressure sensor/pressure switch 2 of evaporative emission control system 2 has a malfunction. The signal offset is outside the permissible range. |
| P1B942F | - | Pressure sensor/pressure switch 2 of evaporative emission control system 2 has a malfunction. There is an erratic signal. |
| P1B9500 | - | Pressure sensor/pressure switch 2 of evaporative emission control system 2 has a short circuit to ground. |
| P1B9511 | - | Pressure sensor/pressure switch 2 of evaporative emission control system 2 has a short circuit to ground. There is a short circuit to ground. |
| P1B9600 | - | Pressure sensor/pressure switch 2 of evaporative emission control system 2 has a short circuit to positive. |
| P1B9612 | - | Pressure sensor/pressure switch 2 of evaporative emission control system 2 has a short circuit to positive. There is a short circuit to positive. |
| P1B9D16 | - | Pressure sensor/pressure switch 2 of evaporative emission control system 3 has a short circuit to positive. The limit value for electrical voltage has not been attained. |
| P1B9D17 | - | Pressure sensor/pressure switch 2 of evaporative emission control system 3 has a short circuit to positive. The limit value for electrical voltage has been exceeded. |
| P1B9D26 | - | Pressure sensor/pressure switch 2 of evaporative emission control system 3 has a short circuit to positive. The signal change rate is below the permissible limit value. |
| P1B9D28 | - | Pressure sensor/pressure switch 2 of evaporative emission control system 3 has a short circuit to positive. The signal offset is outside the permissible range. |
| P1B9D2F | - | Pressure sensor/pressure switch 3 of evaporative emission control system 3 has a malfunction. There is an erratic signal. |
| P1B9E00 | - | Pressure sensor/pressure switch 2 of evaporative emission control system 3 has a short circuit to ground. |
| P1B9F00 | - | Pressure sensor/pressure switch 2 of evaporative emission control system 3 has a short circuit to positive. |
| P1CE300 | - | The values for injector injection quantity adjustment for uniform mixture formation are not available. |
| P1CE365 | - | The values for injector injection quantity adjustment for uniform mixture formation are not available. The signal has too few transitions or events. |
| P1CE400 | - | The values for injector injection quantity adjustment for uniform mixture formation are implausible. |
| P1CE49A | - | The values for injector injection quantity adjustment for uniform mixture formation are implausible. The operating conditions for the component or the system are not satisfied. |
| P1CE500 | - | Injector injection quantity adjustment for uniform mixture formation has detected an excessively lean mixture at at least one cylinder. |
| P1CE577 | - | Injector injection quantity adjustment for uniform mixture formation has detected an excessively lean mixture at at least one cylinder. The commanded position cannot be reached. |
| P1CE600 | - | Injector injection quantity adjustment for uniform mixture formation has detected an excessively rich mixture at at least one cylinder. |
| P1CE678 | - | Injector injection quantity adjustment for uniform mixture formation has detected an excessively rich mixture at at least one cylinder. The adaptation or adjustment is incorrect. |
| P1CEF00 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the upper limit value at at least one cylinder. |
| P1CEF01 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the upper limit value at at least one cylinder. There is a general electrical fault. |
| P1CEF02 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the upper limit value at at least one cylinder. There is a general signal fault. |
| P1CEF03 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the upper limit value at at least one cylinder. There is a frequency or pulse width modulation fault. |
| P1CEF04 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the upper limit value at at least one cylinder. There is an internal fault. |
| P1CEF05 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the upper limit value at at least one cylinder. There is a programming fault. |
| P1CEF06 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the upper limit value at at least one cylinder. There is an algorithm fault. |
| P1CEF85 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the upper limit value at at least one cylinder. There is a signal above the permissible limit value. |
| P1CF000 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the lower limit value at at least one cylinder. |
| P1CF001 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the lower limit value at at least one cylinder. There is a general electrical fault. |
| P1CF002 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the lower limit value at at least one cylinder. There is a general signal fault. |
| P1CF003 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the lower limit value at at least one cylinder. There is a frequency or pulse width modulation fault. |
| P1CF004 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the lower limit value at at least one cylinder. There is an internal fault. |
| P1CF005 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the lower limit value at at least one cylinder. There is a programming fault. |
| P1CF006 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the lower limit value at at least one cylinder. There is an algorithm fault. |
| P1CF084 | - | Injector injection quantity adjustment for cylinder balancing has almost reached the lower limit value at at least one cylinder. There is a signal below the permissible limit value. |
| P1CF100 | - | Injector injection quantity adjustment for cylinder balancing was aborted. |
| P1CF200 | - | The values for injector injection quantity adjustment for cylinder balancing are not available. |
| P200200 | - | The efficiency of the diesel or gasoline particulate filter (cylinder bank 1) is not sufficient. |
| P203211 | - | Temperature sensor 2 'Exhaust system' (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground. |
| P203315 | - | Temperature sensor 2 'Exhaust system' (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P206600 | - | The fill level sensor 'Fuel' on the right has a malfunction. |
| P206609 | - | The fill level sensor 'Fuel' on the right has a malfunction. There is a component fault. |
| P206700 | - | The fill level sensor 'Fuel' on the right has a short circuit to ground. |
| P206800 | - | The fill level sensor 'Fuel' on the right has a short circuit to positive. |
| P207272 | - | The throttle valve is blocked due to ice. The actuator does not close. |
| P207273 | - | The throttle valve is blocked due to ice. The actuator does not open. |
| P208000 | - | Temperature sensor 1 'Exhaust system' (cylinder bank 1) has a malfunction. |
| P208028 | - | Temperature sensor 1 'Exhaust system' (cylinder bank 1) has a malfunction. The signal offset is outside the permissible range. |
| P20802A | - | Temperature sensor 1 'Exhaust system' (cylinder bank 1) has a malfunction. There is no signal change. |
| P208049 | - | Temperature sensor 1 'Exhaust system' (cylinder bank 1) has a malfunction. There is an internal electrical fault. |
| P208064 | - | Temperature sensor 1 'Exhaust system' (cylinder bank 1) has a malfunction. There is an implausible signal. |
| P208100 | - | Temperature sensor 1 'Exhaust system' (cylinder bank 1) has a sporadic malfunction. |
| P208127 | - | Temperature sensor 1 'Exhaust system' (cylinder bank 1) has a sporadic malfunction. The signal change rate is above the permissible limit value. |
| P208428 | - | Temperature sensor 2 'Exhaust system' (cylinder bank 1) has a malfunction. The signal offset is outside the permissible range. |
| P20842A | - | Temperature sensor 2 'Exhaust system' (cylinder bank 1) has a malfunction. There is no signal change. |
| P208449 | - | Temperature sensor 2 'Exhaust system' (cylinder bank 1) has a malfunction. There is an internal electrical fault. |
| P208464 | - | Temperature sensor 2 'Exhaust system' (cylinder bank 1) has a malfunction. There is an implausible signal. |
| P208527 | - | Temperature sensor 2 'Exhaust system' (cylinder bank 1) has a sporadic malfunction. The signal change rate is above the permissible limit value. |
| P208800 | - | Actuator 'Intake camshaft' (cylinder bank 1) has a short circuit to ground. |
| P208811 | - | Actuator 'Intake camshaft' (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground. |
| P208900 | - | Actuator 'Intake camshaft' (cylinder bank 1) has a short circuit to positive. |
| P208912 | - | Actuator 'Intake camshaft' (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive. |
| P209000 | - | Actuator 'Exhaust camshaft' (cylinder bank 1) has a short circuit to ground. |
| P209011 | - | Actuator 'Exhaust camshaft' (cylinder bank 1) has a short circuit to ground. There is a short circuit to ground. |
| P209100 | - | Actuator 'Exhaust camshaft' (cylinder bank 1) has a short circuit to positive. |
| P209112 | - | Actuator 'Exhaust camshaft' (cylinder bank 1) has a short circuit to positive. There is a short circuit to positive. |
| P209600 | - | The mixture is too lean downstream of the catalytic converter (cylinder bank 1). |
| P209700 | - | The mixture is too rich downstream of the catalytic converter (cylinder bank 1). |
| P210100 | - | The throttle valve actuator has a malfunction. |
| P210128 | - | The throttle valve actuator has a malfunction. The signal offset is outside the permissible range. |
| P210129 | - | The throttle valve actuator has a malfunction. There is an invalid signal. |
| P210164 | - | The throttle valve actuator has a malfunction. There is an implausible signal. |
| P210185 | - | The throttle valve actuator has a malfunction. There is a signal above the permissible limit value. |
| P210200 | - | The throttle valve actuator has a short circuit to ground. |
| P210300 | - | The throttle valve actuator has a short circuit to positive. |
| P211100 | - | The throttle valve is jammed open. |
| P211184 | - | The throttle valve is jammed open. There is a signal below the permissible limit value. |
| P211185 | - | The throttle valve is jammed open. There is a signal above the permissible limit value. |
| P212300 | - | Position sensor 1 for the accelerator pedal has a short circuit to positive |
| P212800 | - | Position sensor 2 for the accelerator pedal has a short circuit to positive |
| P213500 | - | The values from the position sensors of the throttle valve are implausible relative to each other. |
| P213600 | - | The values from position sensors ""A/C"" of the throttle valve are implausible relative to each other. |
| P213700 | - | The values from position sensors ""B/C"" of the throttle valve are implausible relative to each other. |
| P213800 | - | The values from the position sensors of the accelerator pedal are implausible relative to each other. |
| P217600 | - | Adaptation of the idle position of the throttle valve actuator was not performed. |
| P217609 | - | Adaptation of the idle position of the throttle valve actuator was not performed. There is a component fault. |
| P217684 | - | Adaptation of the idle position of the throttle valve actuator was not performed. There is a signal below the permissible limit value. |
| P217685 | - | Adaptation of the idle position of the throttle valve actuator was not performed. There is a signal above the permissible limit value. |
| P217691 | - | Adaptation of the idle position of the throttle valve actuator was not performed. The parameter is outside the permissible range. |
| P217700 | - | The mixture (cylinder bank 1) is too lean in partial load operation. |
| P217800 | - | The mixture (cylinder bank 1) is too rich in partial load operation. |
| P218762 | - | The mixture (cylinder bank 1) is too lean at idle speed. The signal comparison is faulty. |
| P218862 | - | The mixture (cylinder bank 1) is too rich at idle speed. The signal comparison is faulty. |
| P219500 | - | The signal from oxygen sensor 1 (cylinder bank 1) is shifted towards ""Lean"". |
| P219585 | - | The signal from oxygen sensor 1 (cylinder bank 1) is shifted towards ""Lean"". There is a signal above the permissible limit value. |
| P219600 | - | The signal from oxygen sensor 1 (cylinder bank 1) is shifted towards ""Rich"". |
| P219684 | - | The signal from oxygen sensor 1 (cylinder bank 1) is shifted towards ""Rich"". There is a signal below the permissible limit value. |
| P219C77 | - | Mixture formation (cylinder 1) is irregular. The commanded position cannot be reached. |
| P219C78 | - | Mixture formation (cylinder 1) is irregular. The adaptation or adjustment is incorrect. |
| P219D77 | - | Mixture formation (cylinder 2) is irregular. The commanded position cannot be reached. |
| P219D78 | - | Mixture formation (cylinder 2) is irregular. The adaptation or adjustment is incorrect. |
| P219E77 | - | Mixture formation (cylinder 3) is irregular. The commanded position cannot be reached. |
| P219E78 | - | Mixture formation (cylinder 3) is irregular. The adaptation or adjustment is incorrect. |
| P219F77 | - | Mixture formation (cylinder 4) is irregular. The commanded position cannot be reached. |
| P219F78 | - | Mixture formation (cylinder 4) is irregular. The adaptation or adjustment is incorrect. |
| P21A077 | - | Mixture formation (cylinder 5) is irregular. The commanded position cannot be reached. |
| P21A078 | - | Mixture formation (cylinder 5) is irregular. The adaptation or adjustment is incorrect. |
| P21A177 | - | Mixture formation (cylinder 6) is irregular. The commanded position cannot be reached. |
| P21A178 | - | Mixture formation (cylinder 6) is irregular. The adaptation or adjustment is incorrect. |
| P220100 | - | The NOx sensor 1(cylinder bank 1) has a malfunction. |
| P220165 | - | The NOx sensor 1(cylinder bank 1) has a malfunction. The signal has too few transitions or events. |
| P222608 | - | The pressure sensor has an electrical fault. There is a signal fault or the message is faulty. |
| P222727 | - | The pressure sensor has a malfunction. The signal change rate is above the permissible limit value. |
| P222728 | - | The pressure sensor has a malfunction. The signal offset is outside the permissible range. |
| P222749 | - | The pressure sensor has a malfunction. There is an internal electrical fault. |
| P222784 | - | The pressure sensor has a malfunction. There is a signal below the permissible limit value. |
| P222785 | - | The pressure sensor has a malfunction. There is a signal above the permissible limit value. |
| P222811 | - | Short circuit to ground in pressure sensor. There is a short circuit to ground. |
| P222821 | - | Short circuit to ground in pressure sensor. The signal amplitude is less than the minimum amplitude. |
| P222912 | - | The pressure sensor has a short circuit to positive. There is a short circuit to positive. |
| P222915 | - | The pressure sensor has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P222922 | - | The pressure sensor has a short circuit to positive. The signal amplitude is greater than the maximum amplitude. |
| P223027 | - | The pressure sensor has a sporadic malfunction. The signal change rate is above the permissible limit value. |
| P223700 | - | The pump current connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. |
| P223786 | - | The pump current connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. There is an incorrect signal. |
| P223C00 | - | The connection of the pump current of lambda sensor 1 (cylinder bank 1) has a malfunction. |
| P224300 | - | The reference voltage connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. |
| P225100 | - | The signal return line connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. |
| P226100 | - | The bypass flap 'Charge air' has a mechanical malfunction. |
| P226D00 | - | The diesel or gasoline particulate filter (cylinder bank 1) is defective or not installed. |
| P226D07 | - | The diesel or gasoline particulate filter (cylinder bank 1) is defective or not installed. There is a mechanical fault. |
| P227000 | - | The signal from oxygen sensor 2 (cylinder bank 1) is shifted towards ""Lean"". |
| P227100 | - | The signal from oxygen sensor 2 (cylinder bank 1) is shifted towards ""Rich"". |
| P227900 | - | A leak was detected in the intake air system. |
| P227907 | - | A leak was detected in the intake air system. There is a mechanical fault. |
| P228000 | - | The air mass flow in the intake air system (cylinder bank 1) has a malfunction. |
| P228200 | - | The intake air system is leaky between the throttle valve and intake valve. |
| P22827A | - | The intake air system is leaky between the throttle valve and intake valve. Leakage or a defective seal was detected. |
| P228800 | - | The pressure control of the fuel injectors is too high. |
| P229F00 | - | NOx sensor 2 (cylinder bank 1) has a malfunction. |
| P229F65 | - | NOx sensor 2 (cylinder bank 1) has a malfunction. The signal has too few transitions or events. |
| P22C800 | - | The valve of the turbocharger is jammed open. |
| P22C900 | - | The valve of the exhaust gas turbocharger is jammed closed. |
| P230000 | - | The actuation of ignition coil 1 has a short circuit to ground. |
| P230100 | - | The actuation of ignition coil 1 has a short circuit to positive. |
| P230300 | - | The actuation of ignition coil 2 has a short circuit to ground. |
| P230400 | - | The actuation of ignition coil 2 has a short circuit to positive. |
| P230600 | - | The actuation of ignition coil 3 has a short circuit to ground. |
| P230700 | - | The actuation of ignition coil 3 has a short circuit to positive. |
| P230900 | - | The actuation of ignition coil 4 has a short circuit to ground. |
| P230A00 | - | The mixture formation (cylinder 1) is erratic and injector injection quantity adjustment is disabled. |
| P230B00 | - | The mixture formation (cylinder 2) is erratic and injector injection quantity adjustment is disabled. |
| P230C00 | - | The mixture formation (cylinder 3) is erratic and injector injection quantity adjustment is disabled. |
| P230D00 | - | The mixture formation (cylinder 4) is erratic and injector injection quantity adjustment is disabled. |
| P230E00 | - | The mixture formation (cylinder 5) is erratic and injector injection quantity adjustment is disabled. |
| P230F00 | - | The mixture formation (cylinder 6) is erratic and injector injection quantity adjustment is disabled. |
| P231000 | - | The actuation of ignition coil 4 has a short circuit to positive. |
| P231200 | - | The actuation of ignition coil 5 has a short circuit to ground. |
| P231300 | - | The actuation of ignition coil 5 has a short circuit to positive. |
| P231500 | - | The actuation of ignition coil 6 has a short circuit to ground. |
| P231600 | - | The actuation of ignition coil 6 has a short circuit to positive. |
| P233600 | - | The knock limit of cylinder 1 was exceeded. |
| P233627 | - | The knock limit of cylinder 1 was exceeded. The signal change rate is above the permissible limit value. |
| P233700 | - | The knock limit of cylinder 2 was exceeded. |
| P233727 | - | The knock limit of cylinder 2 was exceeded. The signal change rate is above the permissible limit value. |
| P233800 | - | The knock limit of cylinder 3 was exceeded. |
| P233827 | - | The knock limit of cylinder 3 was exceeded. The signal change rate is above the permissible limit value. |
| P233900 | - | The knock limit of cylinder 4 was exceeded. |
| P233927 | - | The knock limit of cylinder 4 was exceeded. The signal change rate is above the permissible limit value. |
| P234000 | - | The knock limit of cylinder 5 has been exceeded. |
| P234027 | - | The knock limit of cylinder 5 has been exceeded. The signal change rate is above the permissible limit value. |
| P234100 | - | The knock limit of cylinder 6 has been exceeded. |
| P234127 | - | The knock limit of cylinder 6 has been exceeded. The signal change rate is above the permissible limit value. |
| P23A900 | - | The combustion engine was switched off due to a communication error. |
| P23FE84 | - | The mixture formation (cylinder bank 1) is irregular for small and medium injection quantities. There is a signal below the permissible limit value. |
| P23FE85 | - | The mixture formation (cylinder bank 1) is irregular for small and medium injection quantities. There is a signal above the permissible limit value. |
| P240000 | - | Actuation of the pump in the diagnostic module of the evaporative emission control system has an open circuit. |
| P240100 | - | Actuation of the pump in the diagnostic module of the evaporative emission control system has a short circuit to ground. |
| P240200 | - | Actuation of the pump in the diagnostic module of the evaporative emission control system has a short circuit to positive. |
| P240418 | - | The pump in the diagnostic module of the evaporative emission control system has a malfunction. The limit value for current has not been attained. |
| P240419 | - | The pump in the diagnostic module of the evaporative emission control system has a malfunction. The limit value for current has been exceeded. |
| P240700 | - | The pump in the diagnostic module of the evaporative emission control system has a sporadic malfunction. |
| P240701 | - | The pump in the diagnostic module of the evaporative emission control system has a sporadic malfunction. There is a general electrical fault. |
| P240707 | - | The pump in the diagnostic module of the evaporative emission control system has a sporadic malfunction. There is a mechanical fault. |
| P240726 | - | The pump in the diagnostic module of the evaporative emission control system has a sporadic malfunction. The signal change rate is below the permissible limit value. |
| P240727 | - | The pump in the diagnostic module of the evaporative emission control system has a sporadic malfunction. The signal change rate is above the permissible limit value. |
| P240A00 | - | Actuation of the heater in the diagnostic module of the evaporative emission control system has an open circuit. |
| P240B00 | - | Actuation of the heater in the diagnostic module of the evaporative emission control system has a short circuit to ground. |
| P240C00 | - | Actuation of the heater in the diagnostic module of the evaporative emission control system has a short circuit to positive. |
| P241400 | - | The signal of oxygen sensor 1 (cylinder bank 1) is implausible. |
| P241800 | - | The shutoff valve of the evaporative emission control system has an electrical fault or open circuit. |
| P241900 | - | The shutoff valve of the evaporative emission control system has a short circuit to ground. |
| P242000 | - | The shutoff valve of the evaporative emission control system has a short circuit to positive. |
| P242100 | - | The shutoff valve of the activated charcoal canister is jammed open. |
| P242200 | - | The shutoff valve of the activated charcoal canister sticks in the closed position. |
| P242F00 | - | The ash content of the diesel or gasoline particulate filter is not OK. |
| P242F98 | - | The ash content of the diesel or gasoline particulate filter is not OK. The component or the system has overtemperature. |
| P244A79 | - | The pressure differential in the diesel or gasoline particulate filter (cylinder bank 1) is too low. The mechanical connection has failed. |
| P244A7A | - | The pressure differential in the diesel or gasoline particulate filter (cylinder bank 1) is too low. Leakage or a defective seal was detected. |
| P244A84 | - | The pressure differential in the diesel or gasoline particulate filter (cylinder bank 1) is too low. There is a signal below the permissible limit value. |
| P244B00 | - | The pressure differential in the diesel or gasoline particulate filter (cylinder bank 1) is too high. |
| P244B07 | - | The pressure differential in the diesel or gasoline particulate filter (cylinder bank 1) is too high. There is a mechanical fault. |
| P244B85 | - | The pressure differential in the diesel or gasoline particulate filter (cylinder bank 1) is too high. There is a signal above the permissible limit value. |
| P245000 | - | The shutoff valve of the evaporative emission control system is jammed open. |
| P24507A | - | The shutoff valve of the evaporative emission control system is jammed open. Leakage or a defective seal was detected. |
| P245100 | - | The shutoff valve of the evaporative emission control system is jammed closed. |
| P245204 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has an electrical fault. There is an internal fault. |
| P245223 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has an electrical fault. No signal change: Voltage level is too low. |
| P245228 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has an electrical fault. The signal offset is outside the permissible range. |
| P245249 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has an electrical fault. There is an internal electrical fault. |
| P245296 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has an electrical fault. There is an internal component fault. |
| P245323 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has a malfunction. No signal change: Voltage level is too low. |
| P245327 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has a malfunction. The signal change rate is above the permissible limit value. |
| P245328 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has a malfunction. The signal offset is outside the permissible range. |
| P24532A | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has a malfunction. There is no signal change. |
| P245384 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has a malfunction. There is a signal below the permissible limit value. |
| P245385 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has a malfunction. There is a signal above the permissible limit value. |
| P245398 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has a malfunction. The component or the system has overtemperature. |
| P24539D | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has a malfunction. The component or the system has undertemperature. |
| P245400 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has a short circuit to ground. |
| P245411 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has a short circuit to ground. There is a short circuit to ground. |
| P245500 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has a short circuit to positive. |
| P245515 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P245627 | - | The input for differential pressure sensor 1 in the diesel or gasoline particulate filter has a sporadic malfunction. The signal change rate is above the permissible limit value. |
| P245800 | - | The regeneration duration of the diesel or gasoline particulate filter is not OK. |
| P245863 | - | The regeneration duration of the diesel or gasoline particulate filter is not OK. The duration of the actuation was exceeded: overload protection is active. |
| P245900 | - | The regeneration frequency of the diesel or gasoline particulate filter is not OK. |
| P245904 | - | The regeneration frequency of the diesel or gasoline particulate filter is not OK. There is an internal fault. |
| P245954 | - | The regeneration frequency of the diesel or gasoline particulate filter is not OK. Calibration is missing. |
| P246300 | - | The soot content of the diesel or gasoline particulate filter is not OK. |
| P246304 | - | The soot content of the diesel or gasoline particulate filter is not OK. There is an internal fault. |
| P246B00 | - | The preconditions for regeneration of the diesel or gasoline particulate filter are not fulfilled. |
| P246C97 | - | Function of the diesel or gasoline particulate filter (cylinder bank 1) is restricted. |
| P247884 | - | The signal of temperature sensor 1 ""Exhaust system"" (cylinder bank 1) is implausible. There is a signal below the permissible limit value. |
| P247885 | - | The signal of temperature sensor 1 ""Exhaust system"" (cylinder bank 1) is implausible. There is a signal above the permissible limit value. |
| P24A200 | - | The regeneration of the diesel or gasoline particulate filter (cylinder bank 1) is incomplete. |
| P24BD00 | - | The output for the switchover valve in the diagnostic module of the evaporative emission control system has an electrical fault or an open circuit. |
| P24BE00 | - | The output for the switchover valve in the diagnostic module of the evaporative emission control system has a short circuit to ground. |
| P24BF00 | - | The output for the switchover valve in the diagnostic module of the evaporative emission control system has a short circuit to positive. |
| P24C100 | - | The switchover valve in the diagnostic module of the evaporative emission control system is jammed open. |
| P24D628 | - | Pressure sensor/pressure switch 2 of the evaporative emission control system has a malfunction. The signal offset is outside the permissible range. |
| P24D62A | - | Pressure sensor/pressure switch 2 of the evaporative emission control system has a malfunction. There is no signal change. |
| P24D649 | - | Pressure sensor/pressure switch 2 of the evaporative emission control system has a malfunction. There is an internal electrical fault. |
| P24D684 | - | Pressure sensor/pressure switch 2 of the evaporative emission control system has a malfunction. There is a signal below the permissible limit value. |
| P24D685 | - | Pressure sensor/pressure switch 2 of the evaporative emission control system has a malfunction. There is a signal above the permissible limit value. |
| P24D711 | - | Pressure sensor/pressure switch 2 of the evaporative emission control system has a short circuit to ground. There is a short circuit to ground. |
| P24D722 | - | Pressure sensor/pressure switch 2 of the evaporative emission control system has a short circuit to ground. The signal amplitude is greater than the maximum amplitude. |
| P24D812 | - | Pressure sensor/pressure switch 2 of the evaporative emission control system has a short circuit to positive. There is a short circuit to positive. |
| P24D815 | - | Pressure sensor/pressure switch 2 of the evaporative emission control system has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P24D821 | - | Pressure sensor/pressure switch 2 of the evaporative emission control system has a short circuit to positive. The signal amplitude is less than the minimum amplitude. |
| P250A00 | - | The oil level sensor has an electrical fault. |
| P250A03 | - | The oil level sensor has an electrical fault. There is a frequency or pulse width modulation fault. |
| P250A13 | - | The oil level sensor has an electrical fault. There is an open circuit. |
| P250B00 | - | The oil level sensor has a malfunction. |
| P250B04 | - | The oil level sensor has a malfunction. There is an internal fault. |
| P250B28 | - | The oil level sensor has a malfunction. The signal offset is outside the permissible range. |
| P250B2A | - | The oil level sensor has a malfunction. There is no signal change. |
| P250B84 | - | The oil level sensor has a malfunction. There is a signal below the permissible limit value. |
| P250B85 | - | The oil level sensor has a malfunction. There is a signal above the permissible limit value. |
| P250C00 | - | The oil level sensor has a short circuit to ground. |
| P250C11 | - | The oil level sensor has a short circuit to ground. There is a short circuit to ground. |
| P250C96 | - | The oil level sensor has a short circuit to ground. There is an internal component fault. |
| P250D00 | - | The oil level sensor has a short circuit to positive. |
| P250D15 | - | The oil level sensor has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P250D96 | - | The oil level sensor has a short circuit to positive. There is an internal component fault. |
| P250F00 | - | The engine oil level is too low. |
| P252F00 | - | The engine oil level is too high. |
| P252F85 | - | The engine oil level is too high. There is a signal above the permissible limit value. |
| P253F00 | - | The proportion of fuel in the engine oil is too high. |
| P253F91 | - | The proportion of fuel in the engine oil is too high. The parameter is outside the permissible range. |
| P256300 | - | Position sensor 1 of the boost pressure control flap has a malfunction. |
| P256301 | - | Position sensor 1 of the boost pressure control flap has a malfunction. There is a general electrical fault. |
| P256349 | - | Position sensor 1 of the boost pressure control flap has a malfunction. There is an internal electrical fault. |
| P256400 | - | Position sensor 1 of the boost pressure control flap has a short circuit to ground. |
| P256500 | - | Position sensor 1 of the boost pressure control flap has a short circuit to positive. |
| P259E00 | - | The boost pressure regulator has reached the lower limit of boost pressure control. |
| P259E21 | - | The boost pressure regulator has reached the lower limit of boost pressure control. The signal amplitude is less than the minimum amplitude. |
| P259F00 | - | The boost pressure regulator has reached the upper limit of boost pressure control. |
| P259F22 | - | The boost pressure regulator has reached the upper limit of boost pressure control. The signal amplitude is greater than the maximum amplitude. |
| P262600 | - | The trimming resistor connection of oxygen sensor 1 (cylinder bank 1) has an electrical fault or open circuit. |
| P26CA00 | - | The coolant pump has an electrical fault or an open circuit. |
| P26CB00 | - | The coolant pump has a malfunction. |
| P26CB19 | - | The coolant pump has a malfunction. The limit value for current has been exceeded. |
| P26CE22 | - | The rpm of the coolant pump is too high. The signal amplitude is greater than the maximum amplitude. |
| P26CE7A | - | The rpm of the coolant pump is too high. Leakage or a defective seal was detected. |
| P26D300 | - | The power supply of the coolant pump has a short circuit. |
| P29A100 | - | The power supply of control unit 'Fuel system' is too low. |
| P29A200 | - | The power supply of control unit 'Fuel system' is too high. |
| P2A0000 | - | Oxygen sensor 1 (cylinder bank 1) has a malfunction. |
| P2ABD00 | - | The power consumption of boost pressure regulator 1 is too high. |
| P2B3300 | - | The output for solenoid 2 'Intake' (cylinder bank 1) for CAMTRONIC has an electrical fault or open circuit. |
| P2B3313 | - | The output for solenoid 2 'Intake' (cylinder bank 1) for CAMTRONIC has an electrical fault or open circuit. There is an open circuit. |
| P2B3400 | - | The output for solenoid 2 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to ground. |
| P2B3411 | - | The output for solenoid 2 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to ground. There is a short circuit to ground. |
| P2B3500 | - | The output for solenoid 2 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to positive. |
| P2B3512 | - | The output for solenoid 2 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to positive. There is a short circuit to positive. |
| P2B4000 | - | The sensor signal of solenoid 2 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction. |
| P2B4009 | - | The sensor signal of solenoid 2 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction. There is a component fault. |
| P2B4100 | - | The sensor signal of solenoid 2 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to ground. |
| P2B4200 | - | The sensor signal of solenoid 2 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to positive. |
| P2B4800 | - | The sensor signal of solenoid 2 'Exhaust' (cylinder bank 1) for CAMTRONIC has a malfunction. |
| P2B4809 | - | The sensor signal of solenoid 2 'Exhaust' (cylinder bank 1) for CAMTRONIC has a malfunction. There is a component fault. |
| P2B4900 | - | The sensor signal of solenoid 2 'Exhaust' (cylinder bank 1) for CAMTRONIC has a short circuit to ground. |
| P2B4F00 | - | Solenoid 2 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. |
| P2B4F07 | - | Solenoid 2 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. There is a mechanical fault. |
| P2B4F09 | - | Solenoid 2 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. There is a component fault. |
| P2B5100 | - | Solenoid 2 'Exhaust' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. |
| P2B5107 | - | Solenoid 2 'Exhaust' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. There is a mechanical fault. |
| P2B5109 | - | Solenoid 2 'Exhaust' (cylinder bank 1) for CAMTRONIC has a malfunction or is jammed in the OFF position. There is a component fault. |
| P2B6E00 | - | The temperature sensor of the exhaust gas turbocharger has an electrical fault. |
| P2B6F00 | - | The temperature sensor of boost pressure regulator 1 has a short circuit to ground. |
| P2B6F11 | - | The temperature sensor of boost pressure regulator 1 has a short circuit to ground. There is a short circuit to ground. |
| P2B7000 | - | The temperature sensor of boost pressure regulator 1 has a short circuit to positive. |
| P2B7015 | - | The temperature sensor of boost pressure regulator 1 has a short circuit to positive. There is a short circuit to positive or an open circuit. |
| P2B7100 | - | The temperature sensor of boost pressure regulator 1 has a malfunction. |
| P2B7127 | - | The temperature sensor of boost pressure regulator 1 has a malfunction. The signal change rate is above the permissible limit value. |
| P2B7128 | - | The temperature sensor of boost pressure regulator 1 has a malfunction. The signal offset is outside the permissible range. |
| P2B712A | - | The temperature sensor of boost pressure regulator 1 has a malfunction. There is no signal change. |
| P2B7149 | - | The temperature sensor of boost pressure regulator 1 has a malfunction. There is an internal electrical fault. |
| P2B7184 | - | The temperature sensor of boost pressure regulator 1 has a malfunction. There is a signal below the permissible limit value. |
| P2B7185 | - | The temperature sensor of boost pressure regulator 1 has a malfunction. There is a signal above the permissible limit value. |
| P2B719A | - | The temperature sensor of boost pressure regulator 1 has a malfunction. The operating conditions for the component or the system are not satisfied. |
| P2B7B16 | - | Pressure sensor/pressure switch 3 of the evaporative emission control system has a malfunction. The limit value for electrical voltage has not been attained. |
| P2B7B17 | - | Pressure sensor/pressure switch 3 of the evaporative emission control system has a malfunction. The limit value for electrical voltage has been exceeded. |
| P2B7B26 | - | Pressure sensor/pressure switch 3 of the evaporative emission control system has a malfunction. The signal change rate is below the permissible limit value. |
| P2B7B28 | - | Pressure sensor/pressure switch 3 of the evaporative emission control system has a malfunction. The signal offset is outside the permissible range. |
| P2B7B2F | - | Pressure sensor/pressure switch 3 of the evaporative emission control system has a malfunction. There is an erratic signal. |
| P2B7C00 | - | Pressure sensor/pressure switch 3 of the evaporative emission control system has a short circuit to ground. |
| P2B7D00 | - | Pressure sensor/pressure switch 3 of the evaporative emission control system has a short circuit to positive. |
| P2B8500 | - | The rpm of the coolant pump is too low. |
| P2BA200 | - | The coolant pump is blocked. |
| P2C3000 | - | The output stage of the ignition coil (group 1) has an electrical fault. |
| P2C3100 | - | The output stage of the ignition coil (group 2) has an electrical fault. |
| P2D2800 | - | The drive torque malfunctions during a cold start. |
| P2D2864 | - | The drive torque malfunctions during a cold start. There is an implausible signal. |
| P2D2897 | - | The drive torque malfunctions during a cold start. The system function is restricted. |
| P34AD00 | - | The sensor signal of solenoid 1 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction. |
| P34AD09 | - | The sensor signal of solenoid 1 'Intake' (cylinder bank 1) for CAMTRONIC has a malfunction. There is a component fault. |
| P34AE00 | - | The sensor signal of solenoid 1 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to ground. |
| P34AF00 | - | The sensor signal of solenoid 1 'Intake' (cylinder bank 1) for CAMTRONIC has a short circuit to positive. |
| U001000 | - | Communication with the CAN-bus has a malfunction. |
| U002800 | - | Communication with the drivetrain CAN bus has a malfunction. |
| U008000 | - | Communication with the engine CAN bus has a malfunction. |
| U010008 | - | Communication with the control unit 'combustion engine' has a malfunction. There is a signal fault or the message is faulty. |
| U010009 | - | Communication with the control unit 'combustion engine' has a malfunction. There is a component fault. |
| U010010 | - | Communication with the control unit 'combustion engine' has a malfunction. Reserved for ISO/SAE |
| U010100 | - | Communication with control unit ""Transmission"" has a malfunction. |
| U010187 | - | Communication with control unit ""Transmission"" has a malfunction. The message is missing. |
| U010300 | - | Communication with the electronic selector lever module has a malfunction. |
| U010387 | - | Communication with the electronic selector lever module has a malfunction. The message is missing. |
| U010600 | - | Communication with control unit 'Glow output stage' has a malfunction. |
| U010687 | - | Communication with control unit 'Glow output stage' has a malfunction. The message is missing. |
| U010900 | - | Communication with control unit ""Fuel pump"" has a malfunction. |
| U010987 | - | Communication with control unit ""Fuel pump"" has a malfunction. The message is missing. |
| U010C00 | - | Communication with turbocharger 1 has a malfunction. |
| U010C87 | - | Communication with turbocharger 1 has a malfunction. The message is missing. |
| U010D00 | - | Communication with boost pressure regulator 2 has a malfunction. |
| U010D87 | - | Communication with boost pressure regulator 2 has a malfunction. The message is missing. |
| U011000 | - | Communication with control unit ""Electric machine A"" has a malfunction. |
| U011087 | - | Communication with control unit ""Electric machine A"" has a malfunction. The message is missing. |
| U011500 | - | Communication with control unit 'Drivetrain' has a malfunction. |
| U011587 | - | Communication with control unit 'Drivetrain' has a malfunction. The message is missing. |
| U011D00 | - | Communication with the control unit 'All-wheel drive' has a malfunction. |
| U011D87 | - | Communication with the control unit 'All-wheel drive' has a malfunction. The message is missing. |
| U012000 | - | Communication with the starter or alternator has a malfunction. |
| U012087 | - | Communication with the starter or alternator has a malfunction. The message is missing. |
| U012200 | - | Communication with control unit 'Traction system' has a malfunction. |
| U012287 | - | Communication with control unit 'Traction system' has a malfunction. The message is missing. |
| U013700 | - | Communication with the trailer connection unit has a malfunction. |
| U013787 | - | Communication with the trailer connection unit has a malfunction. The message is missing. |
| U014000 | - | Communication with the signal acquisition and actuation module has a malfunction. |
| U014087 | - | Communication with the signal acquisition and actuation module has a malfunction. The message is missing. |
| U014200 | - | Communication with the rear signal acquisition and actuation module has a malfunction. |
| U014287 | - | Communication with the rear signal acquisition and actuation module has a malfunction. The message is missing. |
| U014602 | - | Communication with the central gateway has a malfunction. There is a general signal fault. |
| U015100 | - | Communication with the supplemental restraint system (SRS) has a malfunction. |
| U015187 | - | Communication with the supplemental restraint system (SRS) has a malfunction. The message is missing. |
| U015500 | - | Communication with the instrument cluster has a malfunction. |
| U015501 | - | Communication with the instrument cluster has a malfunction. There is a general electrical fault. |
| U015502 | - | Communication with the instrument cluster has a malfunction. There is a general signal fault. |
| U015587 | - | Communication with the instrument cluster has a malfunction. The message is missing. |
| U016400 | - | Communication with the air conditioning has a malfunction. |
| U016487 | - | Communication with the air conditioning has a malfunction. The message is missing. |
| U016800 | - | Communication with the electronic ignition lock has a malfunction. |
| U016802 | - | Communication with the electronic ignition lock has a malfunction. There is a general signal fault. |
| U016887 | - | Communication with the electronic ignition lock has a malfunction. The message is missing. |
| U019900 | - | Communication with control unit 'Front door (driver-side)' has a malfunction. |
| U019987 | - | Communication with control unit 'Front door (driver-side)' has a malfunction. The message is missing. |
| U019F00 | - | Communication with the coolant pump has a malfunction. |
| U019F87 | - | Communication with the coolant pump has a malfunction. The message is missing. |
| U020000 | - | Communication with control unit 'Front door (passenger-side)' has a malfunction. |
| U020300 | - | Communication with control unit 'Left front door' has a malfunction. |
| U020387 | - | Communication with control unit 'Left front door' has a malfunction. The message is missing. |
| U020400 | - | Communication with control unit 'Right front door' has a malfunction. |
| U020487 | - | Communication with control unit 'Right front door' has a malfunction. The message is missing. |
| U020600 | - | Communication with control unit 'Soft top control' has a malfunction. |
| U020687 | - | Communication with control unit 'Soft top control' has a malfunction. The message is missing. |
| U025600 | - | Communication with the control unit 'AMG DRIVE UNIT' has a malfunction. |
| U025687 | - | Communication with the control unit 'AMG DRIVE UNIT' has a malfunction. The message is missing. |
| U025E00 | - | Communication with control unit 'Electronic brake booster' has a malfunction. |
| U025E87 | - | Communication with control unit 'Electronic brake booster' has a malfunction. The message is missing. |
| U029A00 | - | Communication with the sensor module of the hybrid/high-voltage battery module has a malfunction. |
| U029A87 | - | Communication with the sensor module of the hybrid/high-voltage battery module has a malfunction. The message is missing. |
| U029D00 | - | Communication with NOx sensor 1 has a malfunction. |
| U029D87 | - | Communication with NOx sensor 1 has a malfunction. The message is missing. |
| U040102 | - | Implausible data were received from control unit 'combustion engine'. There is a general signal fault. |
| U040103 | - | Implausible data were received from control unit 'combustion engine'. There is a frequency or pulse width modulation fault. |
| U040200 | - | Implausible data were received from control unit 'Transmission'. |
| U040208 | - | Implausible data were received from control unit 'Transmission'. There is a signal fault or the message is faulty. |
| U040D00 | - | Implausible data were received from turbocharger 1. |
| U040D08 | - | Implausible data were received from turbocharger 1. There is a signal fault or the message is faulty. |
| U041100 | - | Implausible data were received from control unit ""Electric machine A"". |
| U041108 | - | Implausible data were received from control unit ""Electric machine A"". There is a signal fault or the message is faulty. |
| U042300 | - | Implausible data were received from the instrument cluster. |
| U042308 | - | Implausible data were received from the instrument cluster. There is a signal fault or the message is faulty. |
| U042700 | - | Implausible data were received from the electronic ignition lock. |
| U042708 | - | Implausible data were received from the electronic ignition lock. There is a signal fault or the message is faulty. |
| U043100 | - | Implausible data were received from the front signal acquisition and actuation module. |
| U044200 | - | Implausible data were received from control unit 'Drivetrain'. |
| U044208 | - | Implausible data were received from control unit 'Drivetrain'. There is a signal fault or the message is faulty. |
| U045200 | - | Implausible data were received from the supplemental restraint system (SRS). |
| U045208 | - | Implausible data were received from the supplemental restraint system (SRS). There is a signal fault or the message is faulty. |
| U060008 | - | Communication with engine oil pressure sensor 1 has a malfunction. There is a signal fault or the message is faulty. |
| U060011 | - | Communication with engine oil pressure sensor 1 has a malfunction. There is a short circuit to ground. |
| U060012 | - | Communication with engine oil pressure sensor 1 has a malfunction. There is a short circuit to positive. |
| U060015 | - | Communication with engine oil pressure sensor 1 has a malfunction. There is a short circuit to positive or an open circuit. |
| U060108 | - | Communication with differential pressure sensor 1 has a malfunction. There is a signal fault or the message is faulty. |
| U060111 | - | Communication with differential pressure sensor 1 has a malfunction. There is a short circuit to ground. |
| U060112 | - | Communication with differential pressure sensor 1 has a malfunction. There is a short circuit to positive. |
| U060115 | - | Communication with differential pressure sensor 1 has a malfunction. There is a short circuit to positive or an open circuit. |
| U060908 | - | Communication with intake manifold pressure sensor 1 has a malfunction. There is a signal fault or the message is faulty. |
| U060911 | - | Communication with intake manifold pressure sensor 1 has a malfunction. There is a short circuit to ground. |
| U060912 | - | Communication with intake manifold pressure sensor 1 has a malfunction. There is a short circuit to positive. |
| U060915 | - | Communication with intake manifold pressure sensor 1 has a malfunction. There is a short circuit to positive or an open circuit. |
| U060B08 | - | Communication with boost pressure sensor 1 has a malfunction. There is a signal fault or the message is faulty. |
| U060B11 | - | Communication with boost pressure sensor 1 has a malfunction. There is a short circuit to ground. |
| U060B12 | - | Communication with boost pressure sensor 1 has a malfunction. There is a short circuit to positive. |
| U060B15 | - | Communication with boost pressure sensor 1 has a malfunction. There is a short circuit to positive or an open circuit. |
| U060E08 | - | Communication with the crankcase pressure sensor has a malfunction. |
| U060E11 | - | Communication with the crankcase pressure sensor has a malfunction. |
| U060E15 | - | Communication with the crankcase pressure sensor has a malfunction. |
| U061F08 | - | Communication with exhaust gas temperature sensor 1 (cylinder bank 1) has a malfunction. There is a signal fault or the message is faulty. |
| U061F11 | - | Communication with exhaust gas temperature sensor 1 (cylinder bank 1) has a malfunction. There is a short circuit to ground. |
| U061F12 | - | Communication with exhaust gas temperature sensor 1 (cylinder bank 1) has a malfunction. There is a short circuit to positive. |
| U061F15 | - | Communication with exhaust gas temperature sensor 1 (cylinder bank 1) has a malfunction. There is a short circuit to positive or an open circuit. |
| U062508 | - | Communication with the rail pressure sensor (cylinder bank 1) has a malfunction. There is a signal fault or the message is faulty. |
| U062511 | - | Communication with the rail pressure sensor (cylinder bank 1) has a malfunction. There is a short circuit to ground. |
| U062512 | - | Communication with the rail pressure sensor (cylinder bank 1) has a malfunction. There is a short circuit to positive. |
| U062515 | - | Communication with the rail pressure sensor (cylinder bank 1) has a malfunction. There is a short circuit to positive or an open circuit. |
| U064208 | - | Communication with pressure sensor B in the fuel tank vent line has a malfunction. |
| U064211 | - | Communication with pressure sensor B in the fuel tank vent line has a malfunction. |
| U064215 | - | Communication with pressure sensor B in the fuel tank vent line has a malfunction. |
| U064600 | - | Lost Communication with Motor Electronics Coolant Pump A |
| U064687 | - | Lost Communication with Motor Electronics Coolant Pump A |
| U104188 | - | Communication with the engine CAN bus has a malfunction. Bus OFF |
| U111000 | - | The vehicle speed signal was not received. |
| U111F08 | - | Communication with the pressure sensor upstream of the electric additional compressor has a malfunction. There is a signal fault or the message is faulty. |
| U111F11 | - | Communication with the pressure sensor upstream of the electric additional compressor has a malfunction. There is a short circuit to ground. |
| U111F12 | - | Communication with the pressure sensor upstream of the electric additional compressor has a malfunction. There is a short circuit to positive. |
| U111F15 | - | Communication with the pressure sensor upstream of the electric additional compressor has a malfunction. There is a short circuit to positive or an open circuit. |
| U112081 | - | The security module of the control unit has detected a communication error. Incorrect data were received. |
| U112083 | - | The security module of the control unit has detected a communication error. The checksum for the message has an incorrect value. |
| U112087 | - | The security module of the control unit has detected a communication error. The message is missing. |
| U112A00 | - | Communication with the electric additional compressor has a malfunction. |
| U112A87 | - | Communication with the electric additional compressor has a malfunction. The message is missing. |
| U11AD01 | - | Communication with control unit ""Display cluster"" has a malfunction. There is a general electrical fault. |
| U120000 | - | Communication with NOx sensor 3 has a malfunction. |
| U120087 | - | Communication with NOx sensor 3 has a malfunction. The message is missing. |
| U120100 | - | Communication with NOx sensor 4 has a malfunction. |
| U120187 | - | Communication with NOx sensor 4 has a malfunction. The message is missing. |
| U300100 | - | The control unit was switched off improperly. |
| U300E00 | - | Input signal ""Circuit 15 ON"" is implausible. |
| U301100 | - | Input signal ""Circuit 15 OFF"" is implausible. |