Maintenance: Technical Service Bulletins
- Recalls
- Customer Interest
- A/C - Insufficient Cooling
- Engine - Stalls At Idle or During Deceleration
- Brakes - Roughness During Application
- Distributor Rotor - Engine Bucking/Surging
- Aluminum Wheel - Air Leaks
- Wheels - Steering Wheel Nibble/Vibration
- Polycast Wheels - Paint Chipping or Peeling
- Rear Tires - Excessive Wear On Inboard Edges
- Suspension - Shudder On Acceleration From Standstill
- Rear Tire - Inner Edge Wear
- Courtesy Lamp - Inoperative
- A/T - Synthetic Fluid Availability
- Engine - Rough Idle/Hesitation/Backfire/Stalling
- By Symptom
- Abnormal wear/deterioration
- Abnormal/Uneven wear
- Customer Interest
- A/C - Insufficient Cooling
- Engine - Stalls At Idle or During Deceleration
- Brakes - Roughness During Application
- Distributor Rotor - Engine Bucking/Surging
- Aluminum Wheel - Air Leaks
- Wheels - Steering Wheel Nibble/Vibration
- Polycast Wheels - Paint Chipping or Peeling
- Rear Tires - Excessive Wear On Inboard Edges
- Suspension - Shudder On Acceleration From Standstill
- Rear Tire - Inner Edge Wear
- Courtesy Lamp - Inoperative
- A/T - Synthetic Fluid Availability
- Engine - Rough Idle/Hesitation/Backfire/Stalling
- Driveability
- Improper Alignment
- Inoperative
- Leaks
- Loose
- Poor performance
- Recalls
- Vibration
- Vibration/Pulsating brakes
- All Technical Service Bulletins
- A/C - Filtering Refrigerant After Compressor Replacement
- A/C - Insufficient Cooling
- Engine - Stalls At Idle or During Deceleration
- Brakes - Roughness During Application
- Distributor Rotor - Engine Bucking/Surging
- Engine Cooling Fan - Causes Excessive A/C Pressure
- Wheels - Loss Of Balance Weights
- Aluminum Wheels - Wear/Corrosion Damage
- Aluminum Wheels - Center Ornament Installation
- Brakes - Roughness/Runout Check
- Aluminum Wheel - Air Leaks
- Wheels - Steering Wheel Nibble/Vibration
- Lug Nuts - Proper Torqueing Procedure
- Polycast Wheels - Paint Chipping or Peeling
- Tires - Field Service Locations/Representatives
- Rear Tires - Excessive Wear On Inboard Edges
- Suspension - Shudder On Acceleration From Standstill
- Rear Tire - Inner Edge Wear
- Aluminum Wheel - New Improved Wrench Adapter
- Lug Nuts - Proper Installation/Torqueing Procedure
- Wheel Stud - Removal Procedure
- A/T - AXODE/AXOD New Design Filter Service Tip
- Recall - Part II, Injector/Converter Replacement
- EEC Universal Distributor - Drive Gear Removal Tool
- Courtesy Lamp - Inoperative
- A/C Discharge Hose - Obsolete Part return
- Engine Oil - Recommended Usage
- Engine Coolant - Recycled Coolant Not Authorized
- Recycled Engine Coolant - Service Tips
- Steering Pressure Lines - Revised Torque Specifications
- Accessory Drive Belt - `V' Ribbed Belt Cracking
- A/T - Synthetic Fluid Availability
- A/T, M/T - New `Mercon' Transmission Fluid
- A/T - AX4S/AX4N New Transaxle Fluid
- A/T - Mercon V ATF Usage
- Ignition Timing - Spout Connector Locations
- Specifications Issue Technical Service Bulletin
- A/C - R12 Refrigerant Service Tips
- A/C - R12 Refrigerant Substitutes Service Tip
- R-12 Refrigerant - Substitutes
- Air Conditioning - Use of Correct Fluorescent Tracer Dye
- A/C - Identification of Non Approved Refrigerants
- Engine - Rough Idle/Hesitation/Backfire/Stalling
- Ignition Timing - Incorrect Decal Instructions
- Ignition Timing Procedure - Manual Update
- Camber/Caster Alignment - Shop Manual Revision
- Alignment - Specification Revisions