LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Nissan-Datsun >> 1994 >> Sentra SE-R, Automatic >> Repair and Diagnosis >> Engine Mechanical >> Mechanical >> 2.0L 4-CYL >> Torque Specifications
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Torque Specifications

TORQUE SPECIFICATIONS

Application Ft. Lbs. (N.m)
Axle Shaft Nut 145-203 (197-275)
Camshaft Bearing Cap Bolt (1)
Camshaft Sprocket Bolt 101-116 (137-157)
Connecting Rod Nut
Step 1 10-12 (14-16)
Step 2 28-33 (38-45)
Crankshaft Pulley Bolt 105-112 (142-152)
Crossmember Bolt 33-40 (45-54)
Cylinder Head Outside Bolt (2)
Cylinder Head-To-Cylinder Block Bolt (3)
Step 1 29 (39)
Step 2 58 (79)
Step 3 Loosen All Bolts
Step 4 25-33 (34-45)
Step 5 Tighten Additional 90 Degrees
Step 6 Tighten Additional 90 Degrees
Exhaust Manifold Nut (4) 27-35 (37-47)
Flywheel/Drive Plate Bolt 61-69 (83-94)
Front Engine Mount Through-Bolt 33-40 (45-54)
Front Engine Mount-To-Front Cover Bolt 33-40 (45-54)
Fuel Rail Bolt (5)
Intake Manifold Bolt (6) 13-15 (18-20)
Intake Manifold Collector Bolt/Nut (6) 13-15 (18-20)
Intake Manifold Support Brace Bolt 12-15 (16-20)
Knock Sensor Bolt 15-20 (20-27)
Main Bearing Cap Bolt (7)
Step 1 24-28 (33-38)
Step 2 54-61 (73-83)
Oil Filter Bracket Bolt 12-14 (16-19)
Oil Pressure Regulator Valve Plug 29-51 (39-69)
Oil Pump Pick-Up Tube Bolt 12-14 (16-19)
Oxygen Sensor 13-17 (18-23)
Power Steering Pump Bracket Bolt 33-44 (45-60)
Right (Timing Chain Side) Engine Mount Through-Bolt 33-40 (45-54)
Spark Plug 14-22 (19-30)
Steering Knuckle-To-Strut Bolt 84-98 (114-133)
Throttle Body Bolt
Step 1 (8)
Step 2 13-16 (18-22)
Tie Rod-To-Steering Knuckle Nut 22-29 (30-39)
Timing Chain Guide Bolt
Lower Guide 10-14 (14-19)
Upper Guide 12-14 (16-19)
Torque Converter-To-Drive Plate Bolt
Bolt With Flange 33-43 (45-58)
Bolt Without Flange 29-36 (39-49)
Transaxle Mount Through-Bolt 33-40 (45-54)
Upper Oil Pan Bolt (9)
Upper Transaxle-To-Engine Bolts 51-59 (70-79)
Valve Cover Nut (10)
Water Pump Bolt 12-15 (16-20)
Wheel Lug Nut 72-87 (98-118)
INCH Lbs. (N.m) 
Air Relief Plug 72 (8)
Baffle Plate Bolt 56-66 (6-7)
Crankshaft Rear Seal Housing Bolt 56-72 (6-8)
Front Cover Bolt 56-66 (6-7)
Fuel Injector Clamp Bolt 26-34 (3-4)
Lower Oil Pan Bolt (11) 56-66 (6-7)
Oil Pump Cover Bolt 56-66 (6-7)
Oil Pump Cover Screw 34-44 (4-5)
Rear Cover Plate Bolt 56-66 (6-7)
Timing Chain Tensioner Bolt/Nut 56-72 (6-8)
Water Pump Pulley Bolt 56-72 (6-8)
(1) Tighten bolts using following procedure. See Figure . Bolts No. 9 and 10 and then 1 and 8 on right camshaft to 17 INCH lbs. (2 N.m). Bolts No. 11 and 12 and then 1 and 10 on left camshaft to 17 INCH lbs. (2 N.m). All bolts in sequence to 52 INCH lbs. (5 N.m). Type "A", "B" and "C" bolts to 80-104 INCH lbs. (9-12 N.m). Type "D" bolts to 13-19 ft. lbs. (18-26 N.m).
(2) Information is not available.
(3) Tighten bolts to specification in sequence. See Figure .
(4) Tighten nuts to specification in sequence. See Figure ./
(5) Tighten bolts to 83-96 INCH lbs. (8-11 N.m) and then to 15-20 ft.lbs. (20-27N.m) in sequence. See Figure .
(6) Tighten bolts/nuts to specification in sequence. See Figure .
(7) Tighten bolts to specification in sequence. See Figure .
(8) Tighten bolts to 78-96 INCH lbs. (7-11 N.m).
(9) Tighten bolts to specification in sequence. See Figure .
(10) Tighten nuts to specification in sequence. See Figure .
(11) Tighten bolts to specification in sequence. See Figure .