Diagnostic Procedure

CHECK GROUND CONNECTIONS
1. Turn ignition switch OFF.
2. Loosen and retighten two ground screws on the body.
  Refer to , "GROUND INSPECTION ".
  
  Fig 1: Identifying Body Ground Connections
  Courtesy of NISSAN NORTH AMERICA, INC.
OK or NG

OK: GO TO 2.

NG: Repair or replace ground connections.

CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT-I

Check voltage between ECM terminal 3 and ground under the following conditions with CONSULT-II or tester.

TERMINALS VOLTAGE CHART

Ignition switch	Voltage
OFF	Approximately 0V
ON	Battery voltage (11 - 14V)

OK or NG

OK: GO TO 10.

NG: GO TO 3.

Fig 2: Checking Voltage Between ECM Connector 3 And Ground

Courtesy of NISSAN NORTH AMERICA, INC.

CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT-I
1. Turn ignition switch OFF.
2. Check voltage between ECM terminal 104 and ground with CONSULT-II or tester.
  Voltage: Battery voltage
OK or NG

OK: GO TO 7.

NG: GO TO 4.

Fig 3: Checking Voltage Between ECM Terminal 104 And Ground
Courtesy of NISSAN NORTH AMERICA, INC.
CHECK THROTTLE CONTROL MOTOR RELAY POWER SUPPLY CIRCUIT-II
1. Disconnect ECM harness connector.
2. Disconnect IPDM E/R harness connector E9.
3. Check continuity between ECM terminal 104 and IPDM E/R terminal 47. Refer to WIRING DIAGRAM.
  Continuity should exist.
4. Also check harness for short to ground and short to power.
OK or NG

OK: GO TO 6.

NG: GO TO 5.
DETECT MALFUNCTIONING PART
Check the following.
- Harness connectors E110, M7
- Harness for open or short between ECM and IPDM E/R
  : Repair open circuit or short to ground or short to power in harness or connectors.
CHECK FUSE
1. Disconnect 15A fuse.
2. Check 15A fuse for blown.
OK or NG

OK: GO TO 9.

NG: Replace 15A fuse.
CHECK THROTTLE CONTROL MOTOR RELAY INPUT SIGNAL CIRCUIT-II
1. Disconnect ECM harness connector.
2. Disconnect IPDM E/R harness connector E8.
3. Check continuity between ECM terminal 3 and IPDM E/R terminal 42. Refer to WIRING DIAGRAM.
  Continuity should exist.
4. Also check harness for short to ground and short to power.
OK or NG

OK: GO TO 9.

NG: GO TO 8.
DETECT MALFUNCTIONING PART
Check the following.
- Harness connectors E19, F3
- Harness for open or short between ECM and IPDM E/R
  : Repair open circuit or short to ground or short to power in harness or connectors.
CHECK INTERMITTENT INCIDENT
Refer to , "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".

OK or NG

OK: Replace IPDM E/R. Refer to , "IPDM E/R (INTELLIGENT POWER DISTRIBUTION MODULE ENGINE ROOM) ".

NG: Repair or replace harness or connectors.

CHECK THROTTLE CONTROL MOTOR OUTPUT SIGNAL CIRCUIT FOR OPEN OR SHORT

Turn ignition switch OFF.
Disconnect electric throttle control actuator harness connector.
Disconnect ECM harness connector.

Check harness continuity between the following terminals.

Refer to WIRING DIAGRAM.

TERMINALS CONTINUITY CHART

Electric throttle control actuator terminal	ECM terminal	Continuity
3	5	Should not exist
3	4	Should exist
6	5	Should exist
6	4	Should not exist

Also check harness for short to ground and short to power.

OK or NG

OK: GO TO 11.

NG: Repair or replace.

Fig 4: Identifying Electric Throttle Control Actuator Harness Connector

Courtesy of NISSAN NORTH AMERICA, INC.

CHECK ELECTRIC THROTTLE CONTROL ACTUATOR VISUALLY
1. Remove the intake air duct.
2. Check if foreign matter is caught between the throttle valve and the housing.
OK or NG

OK: GO TO 12.

NG: Remove the foreign matter and clean the electric throttle control actuator inside.

Fig 5: Checking Electric Throttle Control Actuator
Courtesy of NISSAN NORTH AMERICA, INC.
CHECK THROTTLE CONTROL MOTOR
Refer to , "COMPONENT INSPECTION ".

OK or NG

OK: GO TO 13.

NG: GO TO 14.
CHECK INTERMITTENT INCIDENT
Refer to , "TROUBLE DIAGNOSIS FOR INTERMITTENT INCIDENT ".

OK or NG

OK: GO TO 14.

NG: Repair or replace harness or connectors.
REPLACE ELECTRIC THROTTLE CONTROL ACTUATOR
1. Replace the electric throttle control actuator.
2. Perform , "THROTTLE VALVE CLOSED POSITION LEARNING ".
3. Perform , "IDLE AIR VOLUME LEARNING ".
  : INSPECTION END