Active Test
The active test is used to determine and identify details of a malfunction, based on self-diagnosis test results and data obtained in the Data Monitor. In response to instructions from CONSULT instead of those from chassis control module (with built in steering angle sensor) on the vehicle, a drive signal is sent to the actuator to check its operation.
- Never perform ACTIVE TEST while driving the vehicle.
- Always bleed air from brake system before active test.
- Never perform active test when system is malfunctioning.
- When active test is performed while depressing the brake pedal, the brake pedal depressing stroke may change. This is not a malfunction.
- During an active test, sometimes a chassis control warning is displayed and the master warning lamp illuminates on the information display in the combination meter; however, this is not a malfunction.
|
Test item |
Operation |
Description |
|
BRAKE ACTUATOR 1 MODE 1 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 1 MODE 2 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 1 MODE 3 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 2 MODE 1 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 2 MODE 2 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 2 MODE 3 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 3 MODE 1 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 3 MODE 2 |
Start |
Controls brake fluid pressure. |
|
BRAKE ACTUATOR 3 MODE 3 |
Start |
Controls brake fluid pressure. |
|
MASTER WARNING ACTIVE |
On |
If touching "On" with the master warning lamp not illuminated, the master warning lamp illuminates. Stops in approximately 1 minute. |
|
Off |
The master warning lamp turns OFF. (vehicle in normal state) |
|
|
HDC DISP |
-- |
|
|
BRAKE HOLD DISP |
INACT |
Does not display the operating status of hill start assist function displayed on the information display in the combination meter. |
|
ACTIVE |
Displays the operating status of hill start assist function displayed on the information display in the combination meter. |
|
|
READY |
Displays the ready status of hill start assist function displayed on the information display in the combination meter. |
|
|
ERROR |
Does not display the operating status of hill start assist function displayed on the information display in the combination meter. |
|
|
AEB DISP |
On |
Displays the operating status of intelligent engine brake (brake control) function displayed on the information display in the combination meter. |
|
Off |
Does not display the operating status of intelligent engine brake (brake control) function displayed on the information display in the combination meter. |
|
|
FL TIRE DISP |
On |
Displays the front LH tire on the information display in the combination meter. |
|
Off |
Does not display the front LH tire on the information display in the combination meter. |
|
|
FR TIRE DISP |
On |
Displays the front RH tire on the information display in the combination meter. |
|
Off |
Does not display the front RH tire on the information display in the combination meter. |
|
|
RL TIRE DISP |
On |
Displays the rear LH tire on the information display in the combination meter. |
|
Off |
Does not display the rear LH tire on the information display in the combination meter. |
|
|
RR TIRE DISP |
On |
Displays the rear RH tire on the information display in the combination meter. |
|
Off |
Does not display the rear RH tire on the information display in the combination meter. |
|
|
VEHICLE DISP |
On |
Displays the operating status of active ride control (brake control) function displayed on the information display in the combination meter. |
|
Off |
Does not display the operating status of active ride control (brake control) function displayed on the information display in the combination meter. |
|
|
INTERRUPT DISP |
NO REQ |
Does not display the interrupt of hill start assist function displayed on the information display in the combination meter. |
|
READY |
Displays the interrupt of ready status of hill start assist function displayed on the information display in the combination meter. |
|
|
ACT |
Displays the interrupt of operating status of hill start assist function displayed on the information display in the combination meter. |
|
|
TURN DISP |
NO DISP |
Does not display the turning status on the information display in the combination meter. |
|
LH |
Displays the LH turning status on the information display in the combination meter. |
|
|
RH |
Displays the RH turning status on the information display in the combination meter. |
|
|
Automatic brake hold lamp active |
Standby (white) lamp lighting |
Turn ON the automatic brake hold indicator lamp (white) in the combination meter. |
|
Operation (green) lamp lighting |
Turn ON the automatic brake hold indicator lamp (green) in the combination meter. |
|
|
Off |
Turn OFF the automatic brake hold indicator lamp (white or green) in the combination meter. |
|
|
Automatic brake hold SW lamp active |
LED lighting |
Turn On the automatic brake hold switch indicator. |
|
LED blinking (1Hz) |
Blink the automatic brake hold switch indicator. |
|
|
Off |
Turn OFF the automatic brake hold switch indicator. |