Specifications Index
CUTLASS SUPREME, GRAND PRIX, LUMINA, MONTE CARLO & REGAL SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | |||
| Automatic | A/C SYSTEM SPECIFICATIONS | ||
| Manual | A/C SYSTEM SPECIFICATIONS | ||
| Torque | |||
| Automatic | TORQUE SPECIFICATIONS | ||
| Manual | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | 151 Ft. lbs. (205 N.m) | ||
| Battery | See table under CAPACITIES | ||
| Brakes | |||
| Bleeding Sequence | RR, LF, LR, RF | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drum Brakes | |||
| Service Specifications | DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | BELT ADJUSTMENT | ||
| Drive Belt Routing | SERPENTINE BELT ROUTING | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM SPECIFICATIONS | ||
| Radiator Cap Pressure | 15 psi | ||
| Thermostat R & I | |||
| 3.1L | THERMOSTAT | ||
| 3.4L | THERMOSTAT | ||
| 3.8L | THERMOSTAT | ||
| Water Pump R & I | |||
| 3.1L | WATER PUMP | ||
| 3.4L | WATER PUMP | ||
| 3.8L | WATER PUMP | ||
| Engine Mechanical | |||
| 3.1L | |||
| Compression | Lowest Cylinder not less than 70% of highest and no cylinder less than 100 psi (689 kPa) | ||
| Oil Pressure | 15 psi (103 kPa) at 1100 RPM-minimum | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3.4L | |||
| Compression | Lowest Cylinder not less than 70% of highest and no cylinder less than 100 psi (689 kPa) | ||
| Oil pressure | 15 psi (103 kPa) at 1100 RPM-minimum | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3.8L | |||
| Compression | Lowest Cylinder not less than 70% of highest and no cylinder less than 100 psi (689 kPa) | ||
| Oil pressure | 60 psi (414 kPa) at 1850 RPM using 10W-30 oil | ||
| Overhaul | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 3.1L | 61 lb. ft. (83 N.m) | ||
| 3.4L | 60 lb. ft. (82 N.m) | ||
| 3.8L | |||
| Step 1 | 11 lb. ft. (15 N.m) | ||
| Step 2 | Additional 50 Degrees | ||
| Fuel System | |||
| Pressure Specification | |||
| 3.1L | 41-47 psi (283-324 kPa) | ||
| 3.4L & 3.8L | 48-55 psi (331-379 kPa) | ||
| Fuel Pressure Test Procedure | |||
| 3.1L | FUEL SYSTEM PRESSURE TEST | ||
| 3.4L | FUEL SYSTEM PRESSURE TEST | ||
| 3.8L | FUEL SYSTEM PRESSURE TEST | ||
| Fuel Filter Location | In-pipe fuel filter is in fuel line between tank and fuel rail. | ||
| Fuel Filter R & I | FUEL FILTER | ||
| Ignition | |||
| Firing Order & Cylinder Identification | See appropriate figure under FIRING ORDER & TIMING MARKS | ||
| Ignition Wires (Resistance) | 30,000 Ohms Maximum | ||
| Ignition Wires (Routing) | See appropriate figure under FIRING ORDER & TIMING MARKS | ||
| Spark Plug | |||
| 3.1L | |||
| Type | 41-940 | ||
| Gap | .060 In. (1.52 mm) | ||
| Torque | 11 Ft. lbs. (15 N.m) | ||
| 3.4L | |||
| Type | 41-919 | ||
| Gap | .045 In. (1.14 mm) | ||
| Torque | 11 Ft. lbs. (15 N.m) | ||
| 3.8L | |||
| Type | 41-921 | ||
| Gap | .060 In. (1.52 mm) | ||
| Torque | 11 Ft. lbs. (15 N.m) | ||
| Starting | |||
| Starter | STARTER | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 100 Ft. lbs. (136 N.m) | ||