LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Porsche >> 2000 >> 911 Carrera, 2D Convertible, Standard >> Repair and Diagnosis >> Engine Performance >> Remove, Overhaul & Install >> Fuel System, Electronic Injection, Programming Control Module - 911 CARRERA (996) >> System M11 >> 24 70 Programming DME control module >> Programming
April 5, 2026: LEMON Manuals is launched! Read the announcement.

24 70 Programming DME control module: Programming

  1. Connect and switch on the Porsche System Tester 2 and switch on the ignition.
  2. Select 911 (996)  in the Vehicle type  menu.
  3. Select DME  in the Control unit  menu and press the double arrow key "FORWORD".
  4. Select Program control unit  in the DME function selection  menu and press the double arrow key "FORWORD".
  5. Select "Read control units" and press the double arrow key "FORWORD".
  6. Install new DME control module.
  7. Select Program control unit  in the Control unit programming  menu and press the double arrow key "FORWORD".
  8. Ensure that all requirements requested on the screen are fulfilled and then press the double arrow key "FORWORD".
  9. The following message appears on the screen:

    "Input Vehicle Ident. Number". 

    Input Vehicle Identification Number and press the double arrow key "FORWORD".

  10. The following message appears on the screen:

    "Please confirm input" 

    Confirm input with the "F7" key.

  11. The following message appears on the screen:

    "Input old DME programming code" 

    Input DME programming code and press the double arrow key "FORWORD".

  12. The following message appears on the screen:

    "Please confirm input" 

    Confirm input with the "F7" key.

  13. The following message appears on the screen:

    "Input new programming code" 

    Input new DME programming code and press the double arrow key "FORWORD".

  14. The following message appears on the screen:

    "Please confirm input" 

    Confirm input with the "F7" key.

  15. The following message appears on the screen:

    "Input new immobilizer code" 

    Input immobilizer code and press the double arrow key "FORWORD".

  16. The following message appears on the screen:

    "Please confirm input" 

    Confirm input with the "F7" key.

  17. The following message appears on the screen:

    "Select data record" 

    Select data record according to the allocation table and press the double arrow key "FORWORD".

    The control module will now be programmed. Programming will take approx. 5 minutes.

    WARNING: > Never interrupt the programming process
  18. The following message will appear after the programming time has elapsed:

    "Programming was completed successfully" 

    Press the double arrow key "FORWORD", switch the ignition off and then on again.

    This completes programming of the DME control module.

CATALYTIC CONVERTER VERSION, ITEM NUMBER AND VEHICLE IDENTIFICATION NUMBER

Catalytic converter version Vehicle Ident. Number Catalytic converter item number
OBD II control module WP0xx2  xxxW  xxxxxxx 996.113.021.53
996.113.022.53
RoW control module WPOZZZ  xxxW  xxxxxxx 996.113.021.52
996.113.022.52
German control module (tri-metal catalytic converter) WPOZZZ  xxxW  xxxxxxx 996.113.021.54
996.113.022.54
OBD II control module WP0xx2  xxxX  xxxxxxx 996.113.021.53
996.113.022.53
RoW control module WPOZZZ  xxxX  xxxxxxx 996.113.021.52
996.113.022.52
German control module (tri-metal catalytic converter) WPOZZZ  xxxX  xxxxxxx 996.113.021.54
996.113.022.54
NOTE: The DME control module can also be reprogrammed using the Porsche System Tester 2. In this case, the old data record will be overwritten by a new record (e.g. RoW instead of Germany)

Program map/data  must be selected in Step  7 if reprogramming is necessary.

WARNING: Risk of damage if allocation is incorrect!

Ensure correct allocation of the data record in the control module to the installed catalytic converter (refer to CATALYTIC CONVERTER VERSION, ITEM NUMBER AND VEHICLE IDENTIFICATION NUMBER  table)

scientia non olet · About LEMON Manuals