Specifications Index
9-7X SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | 103 Ft. Lbs. (140 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR, LR, RF, LF | ||
| Disc Brakes | |||
| Service Specifications | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drum Brakes | NA | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | NA | ||
| Belt Routing | |||
| 4.2L | See figure under DRIVE BELT REPLACEMENT . | ||
| 5.3L | See figure under DRIVE BELT REPLACEMENT - ACCESSORY or DRIVE BELT REPLACEMENT - AIR CONDITIONING . | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM DESCRIPTION AND OPERATION | ||
| Radiator Cap Pressure | Radiator cap pressure is stamped on cap. | ||
| Thermostat R & I | |||
| 4.2L | THERMOSTAT REPLACEMENT (4.2L ENGINE) | ||
| 5.3L | THERMOSTAT REPLACEMENT (5.3L ENGINE) | ||
| Water Pump R & I | |||
| 4.2L | WATER PUMP REPLACEMENT (LL8) | ||
| 5.3L | WATER PUMP REPLACEMENT (LH6) | ||
| Engine Mechanical | |||
| 4.2L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | 12 psi (85 kPa) minimum at 1,200 RPM | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 5.3L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil pressure | 6 psig (41 kPa) at 1,000 RPM 18 psig (124 kPa) at 2,000 RPM 24 psig (165 kPa) at 4,000 RPM |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | |||
| 4.2L | |||
| First Pass | 18 Ft. Lbs. (25 N.m) | ||
| Final Pass | 50 degrees | ||
| 5.3L | |||
| First Pass | 15 Ft. Lbs. (20 N.m) | ||
| Second Pass | 37 Ft. Lbs. (50 N.m) | ||
| Final Pass | 74 Ft. Lbs. (100 N.m) | ||
| Fuel System | |||
| 4.2L | |||
| Pressure Specification | 50-57 psi (345-395 kPa) | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | Fuel filter is contained in fuel sender assembly inside fuel tank. | ||
| Fuel Filter R & I | FUEL SENDER ASSEMBLY REPLACEMENT | ||
| 5.3L | |||
| Pressure Specification | 50-60 psi (345-414 kPa) | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | Fuel filter is contained in fuel sender assembly inside fuel tank. | ||
| Fuel Filter R & I | FUEL SENDER ASSEMBLY REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 4.2L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| 5.3L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | NA | ||
| Ignition Wires (Routing) | NA | ||
| Spark Plug | |||
| 4.2L | |||
| Type | AC 41-981 | ||
| Gap | 0.0425 In. (1.08 mm) | ||
| Torque | 13 Ft. Lbs. (18 N.m) | ||
| 5.3L | |||
| Type | GM P/N 12571164 or AC 41-985 | ||
| Gap | 0.04 In. (1.02 mm) | ||
| Torque | New Cylinder Heads - 15Ft. Lbs. (20 N.m) Used Cylinder Heads - 11 Ft. Lbs. (15 N.m) |
||
| Starting | |||
| Starter | STARTING SYSTEM DESCRIPTION AND OPERATION | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 103 Ft. Lbs. (140 N.m) | ||