LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Saab >> 2011 >> 9-4X Aero >> Repair and Diagnosis (Single Page) >> Accessories & Equipment >> Communication Devices >> Bus And Diagnostics Communication >> Technical data >> Electronic Brake Control Module Scan Tool Information >> Electronic Brake Control Module Scan Tool Data Parameters
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Electronic Brake Control Module Scan Tool Data Parameters

Parameter System State Expected Value Description
Operating Conditions:  Ignition ON
ABS Pump Motor Voltage - 0 V The scan tool displays the commanded pump motor voltage.
Acceleration Sensor Longitudinal Signal - Varies The scan tool displays 0-5 V depending on the vehicle's longitudinal acceleration.
Antilock Braking System - On The scan tool displays On or Off. Off is displayed when the ABS is disabled.
Brake Booster Electric Vacuum Pump - On/Off The scan tool displays On or Off. On is displayed when the electric vacuum pump motor is commanded On.
Brake Booster Vacuum Sensor Supply - 4.8-5.2 V The scan tool displays V. This is the voltage supplied to the brake booster vacuum sensor.
Brake Booster Vacuum Sensor - Varies The scan tool displays kPa (PSI) depending on the vacuum applied to the brake booster.
Brake Fluid Level Sensor - OK The scan tool displays OK when the brake fluid is at correct level and Low when the brake fluid is low.
Brake Pedal Position Sensor Brake pedal released Inactive The scan tool displays Inactive or Active depending on the state of the brake pedal.
Brake pedal applied Active
Brake Pressure Sensor Brake pedal released 0-1 V The scan tool displays 0-5 V depending on the applied hydraulic brake pressure.
Brake pedal applied 1-5 V
Dynamic Rear Proportioning Status - On The scan tool displays On or Off. Off is displayed when the dynamic rear proportioning system is disabled.
Lateral Acceleration Signal - Varies The scan tool displays 0-5 V depending on the vehicle's lateral acceleration.
Left Front Inlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the left front inlet solenoid valve is commanded ON.
Left Front Outlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. "Active" is displayed when the left front outlet solenoid valve is commanded ON.
Left Front Wheel Speed Sensor - 0 km/h (0 MPH) The scan tool displays km/h (MPH) depending on the current speed of the left front wheel speed sensor.
Left Rear Inlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the left rear inlet solenoid valve is commanded ON.
Left Rear Outlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the left rear outlet solenoid valve is commanded ON.
Left Rear Wheel Speed Sensor - 0 km/h (0 MPH) The scan tool displays km/h (MPH) depending on the current speed of the left rear wheel speed sensor.
Pump Motor Relay Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the pump motor is commanded ON.
Primary Isolation Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. "Active" is displayed when the isolation solenoid valve is commanded ON.
Primary Prime Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the prime solenoid valve is commanded ON.
Right Front Inlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the right front inlet solenoid valve is commanded ON.
Right Front Outlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the right front outlet solenoid valve is commanded ON.
Right Front Wheel Speed Sensor - 0 km/h (0 MPH) The scan tool displays km/h (MPH) depending on the current speed of the right front wheel speed sensor.
Right Rear Inlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the right rear inlet solenoid valve is commanded ON.
Right Rear Outlet Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the right rear outlet solenoid valve is commanded ON.
Right Rear Wheel Speed Sensor - 0 km/h (0 MPH) The scan tool displays km/h (MPH) depending on the current speed of the right rear wheel speed sensor.
Secondary Isolation Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. "Active" is displayed when the isolation solenoid valve is commanded ON.
Secondary Prime Solenoid Valve Feedback - Inactive The scan tool displays Inactive or Active. Active is displayed when the prime solenoid valve is commanded ON.
Steering angle Steering wheel in straight position -5 to +5° The scan tool displays°. This is the current position of the steering angle sensor.
Steering wheel turned left until stop 450-550°
Steering wheel turned right until stop -550 to - 450°
System Voltage - 11-14 V The scan tool displays V. This is the current battery voltage.
Traction Control System - On The scan tool displays On or Off. Off is displayed when traction control is disabled.
Variable Effort Steering Solenoid Valve Command - Varies The scan tool displays A. This is the current applied to the variable effort steering solenoid valve.
Variable Effort Steering Solenoid Valve Feedback - Varies The scan tool displays A. This is the variable effort steering solenoid valve feedback signal.
Vehicle Stability Enhancement System Relay Feedback - Active The scan tool displays Inactive or Active depending on the state of the stability control.
Vehicle Stability System - On The scan tool displays On or Off. Off is displayed when stability control is disabled.
Yaw Rate Signal Sensor - Varies The scan tool displays 0-5 V depending on the vehicle's yaw rate.
scientia non olet · About LEMON Manuals