Specifications Index
"L" SERIES SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | |||
| Automatic | SPECIFICATIONS | ||
| Manual | SPECIFICATIONS | ||
| Torque | |||
| Automatic | TORQUE SPECIFICATIONS | ||
| Manual | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | Tighten nut to 74-118 ft. lbs. (100-160 N.m). Loosen nut and retighten finger tight. Tighten nut to 15 ft. lbs. (20 N.m), then tighten nut an additional 90 degrees. Continue to tighten nut sufficiently to install NEW cotter pin. |
||
| Battery | BATTERY SPECIFICATIONS | ||
| Brakes | |||
| Bleeding Sequence | RR, LF, LR, RF | ||
| Disc Brakes | DISC BRAKE SPECIFICATIONS | ||
| Drum Brakes | DRUM BRAKE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| R & I | |||
| 2.2L | ENGINE DRIVE BELT REPLACEMENT (IN-VEHICLE) | ||
| 3.0L | DRIVE BELT REPLACEMENT (IN-VEHICLE) | ||
| Belt Routing | |||
| 2.2L | See appropriate illustration under ENGINE DRIVE BELT REPLACEMENT (IN-VEHICLE) | ||
| See appropriate illustration under DRIVE BELT REPLACEMENT (IN-VEHICLE) | |||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | 20 psi (138 kPa) | ||
| Thermostat R & I | |||
| 2.2L | THERMOSTAT INLET HOUSING & ELEMENT | ||
| 3.0L | THERMOSTAT INLET HOUSING AND ELEMENT | ||
| Water Pump R & I | |||
| 2.2L | WATER PUMP REPLACEMENT (IN-VEHICLE) | ||
| 3.0L | WATER PUMP REPLACEMENT (IN-VEHICLE) | ||
| Engine Mechanical | |||
| 2.2L | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | 50-80 psi (344.75-551.60 kPa) Minimum at 1000 RPM | ||
| Overhaul | DESIGN SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 3.0L | |||
| Compression | ENGINE COMPRESSION | ||
| Oil Pressure | 16 psi (110 kPa) Minimum, Engine Idle at Normal Operating Temperature | ||
| Overhaual | ENGINE SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 55 Ft. Lbs. (75 N.m) | ||
| Fuel System | |||
| Pressure Specification Ignition ON, Engine OFF |
50-60 psi (345-414 kPa) | ||
| Fuel Pressure Test Procedure | FUEL SYSTEM PRESSURE TEST (SATURN) | ||
| Fuel Filter R & I | |||
| 2.2L | FUEL FILTER | ||
| 3.0L | FUEL FILTER | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Not equipped with high tension wires. Ignition coils are connected directly to spark plugs by boots. | ||
| Ignition Wires (Routing) | NA | ||
| Spark Plugs | |||
| Type | AC 41-628 | ||
| Gap | .045 In. (1.14 mm) | ||
| Torque | 15 Ft. Lbs. (20 N.m) | ||
| Starting | |||
| Starter | STARTER SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specification | See graphic in L SERIES | ||
| Torque | See procedures in ALIGNMENT, WHEELS & TIRES | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | Initial Torque 46 Ft. Lbs. (63 N.m) Final Torque 92 Ft. Lbs. (125 N.m) |
||