LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Saturn >> 2005 >> Relay AWD >> Repair and Diagnosis >> External Pages >> Different car >> Section 190 (Frame And Underbody) >> Repair Instructions >> Front Frame Replacement >> Installation Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Installation Procedure

WARNING: This page is about a different car, the 2007 Pontiac Montana SV6, 2007 Chevrolet Uplander, and 2007 Buick Terraza. However, it is still accessible from the selected car via links, so may be relevant.
  1. If you are replacing the frame, perform the following steps:
    1. Install the lower control arms to the frame. Refer to Lower Control Arm Replacement .
    2. Install the frame insulators to the frame. Refer to Front Frame Cushion or Insulator Replacement .
  2. Position the transaxle table with the frame under the vehicle.
    3. Fig 1: Identifying Utility Stand
    GM333118Courtesy of GENERAL MOTORS CORP.
    IMPORTANT: Ensure that the power steering cooler line does not become trapped by the engine mount during this step.
  3. Lower the vehicle until the frame is close to the vehicle.
  4. Adjust the utility straps as necessary in order to align the powertrain mounts with the frame.
    5. IMPORTANT: Ensure that the alignment pins remain installed during the frame installation.
  5. Inserting two 19 mm (0.75 in) diameter X 203 mm (8.0 in) long guide pins or drill bits into the frame right side alignment holes in order to align the frame.
    6. Fig 2: Identifying Frame Bolts
    GM1548651Courtesy of GENERAL MOTORS CORP.
    NOTE: Refer to Fastener Notice .
  6. Install the frame front bolts (2).

    Tighten:  Tighten the bolts to 130 N.m (96 lb ft).

  7. Install the frame straps (5) and bolts (3).

    Tighten:  Tighten the bolts to 50 N.m (37 lb ft).

  8. Install the frame rear bolts (4).

    Tighten:  Tighten the bolts to 240 N.m (177 lb ft).

  9. Remove the alignment pins from the frame.
  10. Install the transaxle mount nuts. Refer to Transmission Mount Replacement .
  11. Install the engine mount nuts. Refer to Engine Mount Replacement .
  12. Install the wheel speed sensor wiring harnesses to the lower control arms.
  13. Connect the wheel speed sensor electrical connectors.
  14. Install the lower ball joints to the steering knuckles. Refer to Steering Knuckle Replacement .
  15. Install the power steering cooler pipe to the frame. Refer to Power Steering Cooler Pipe/Hose Replacement .
  16. Install the front engine splash shield. Refer to Engine Splash Shield Replacement .
  17. Install the power steering gear to the frame. Refer to Power Steering Gear Replacement .
  18. Install the power steering gear bolts. Refer to Power Steering Gear Replacement .
  19. Install the power steering gear heat shield. Refer to Power Steering Gear Heat Shield Replacement .
  20. Install the stabilizer shaft. Refer to Stabilizer Shaft Replacement (with Rear IRS) or Stabilizer Shaft Replacement (with Rear Twist Axle) .
  21. Install both tie rod ends to the steering knuckles. Refer to Steering Knuckle Replacement .
  22. Install the front fender liner. Refer to Front Wheelhouse Liner Replacement .
  23. Install the front tires and wheels. Refer to Tire and Wheel Removal and Installation .
  24. Lower the vehicle.
  25. Remove the engine support fixture.
  26. Inspect the front wheel alignment and adjust the toe angle if necessary. Refer to Measuring Wheel Alignment .
scientia non olet · About LEMON Manuals