Specifications Index
VUE SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 151 Ft. Lbs. (205 N.m) | ||
| Rear | 81 Ft. Lbs. (110 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | RR, LF, LR, RF | ||
| Disc Brakes | DISC BRAKE COMPONENT SPECIFICATIONS | ||
| Drum Brakes | DRUM BRAKE COMPONENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | NA | ||
| Belt Routing | |||
| 2.2L | NA | ||
| 3.5L | See figure under DRIVE BELT REPLACEMENT | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM DESCRIPTION AND OPERATION | ||
| Radiator Cap Pressure | Radiator cap pressure is stamped on cap. | ||
| Thermostat R & I | |||
| 2.2L | ENGINE COOLANT THERMOSTAT REPLACEMENT (L61) | ||
| 3.5L | ENGINE COOLANT THERMOSTAT REPLACEMENT (L66) | ||
| Water Pump R & I | |||
| 2.2L | WATER PUMP REPLACEMENT (2.2L (L61)) | ||
| 3.5L | WATER PUMP REPLACEMENT (3.5L (L66)) | ||
| Engine Mechanical | |||
| 2.2L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil Pressure | 50-80 psi (344.75-551.60 kPa) minimum at 1,000 RPM | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 3.5L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil pressure At 176°F (80°C) |
10 psi (70 kPa) at idle 71 psi (490 kPa) at 3,000 RPM |
||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | |||
| 2.2L | |||
| First Pass | 39 Ft.Lbs. (53 N.m) | ||
| Final Pass | 25 degrees | ||
| 3.5L | 54 Ft. Lbs. (74 N.m) | ||
| Fuel System | |||
| Pressure Specification | |||
| 2.2L | 50-60 psi (345-414 kPa) | ||
| 3.5L | 48-56 psi (330-382 kPa) | ||
| Fuel Pressure Test Procedure | |||
| 2.2L | FUEL SYSTEM DIAGNOSIS | ||
| 3.5L | FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | Fuel filter is located in primary fuel tank module. | ||
| Fuel Filter R & I | |||
| 2.2L | FUEL TANK MODULE REPLACEMENT - PRIMARY | ||
| 3.5L | FUEL TANK MODULE REPLACEMENT - PRIMARY | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| 2.2L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| 3.5L | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil on plug | ||
| Ignition Wires (Routing) | Coil on plug | ||
| Spark Plug | |||
| 2.L | |||
| Type | GM P/N 12569190 or AC DELCO P/N 41-981 | ||
| Gap | 0.043-0.037 In. (1.1-0.95 mm) | ||
| Torque | 15 Ft. Lbs. (20 N.m) | ||
| 3.5L | |||
| Type | NGK IZFR5K-11 or DENSO SKJ16DR-M11 | ||
| Gap | 0.039-0.043 In. (1.0-1.1 mm) | ||
| Torque | 13 Ft. Lbs. (18 N.m) | ||
| Starting | |||
| Starter | STARTING SYSTEM DESCRIPTION AND OPERATION | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 92 Ft. Lbs. (125 N.m) | ||