LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Saturn >> 2007 >> Ion Red Line >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls And Fuel - Troubleshooting & Diagnosis >> Inspection/Maintenance (I/M) Complete System Set Procedure >> Test Description
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Test Description

The numbers below refer to the step numbers on the diagnostic table.

  1. 2:  This step is to run the heated oxygen sensor (HO2S) heater diagnostics and initiate the EVAP System diagnostic.
  2. 3:  This step is to run the EVAP, secondary air injection (AIR) and the oxygen sensor diagnostics. The EVAP Test begins once the engine coolant reaches a calibrated temperature. The AIR Test, if equipped, begins shortly after Closed Loop and the indicated speed is achieved. The oxygen sensor diagnostics begin once the engine is at operating temperature, in Closed Loop fuel control, and a calibrated amount of time has elapsed.
  3. 4:  This step is to run the Catalyst Tests. This test runs during the idle period immediately following a cruise period that meets a minimum calibrated RPM and time period.
Inspection/Maintenance (I/M) Complete System Set Procedure

Step Action Value(s) Yes No
1 Did you perform the Inspection/Maintenance (I/M) System Check? - Go to Step 2  Go to Inspection/Maintenance (I/M) System Check 
2 
    IMPORTANT: Whenever the ignition is turned ON, ignition positive voltage is supplied to the heated oxygen sensor (HO2S) heaters. After verifying the enable criteria, turn OFF the ignition for approximately 5 minutes to allow the sensors to cool before continuing with the test. Once the engine is started, DO NOT turn the engine OFF for the remaining portion of the set procedure.
  1. Preprogram the scan tool with the vehicle information before the ignition is turned ON.
  2. Ensure the vehicle is within the Conditions for Running specified in the supporting text.
  3. Turn OFF all of the accessories, e.g., A/C, blower fan, etc.
  4. Set the vehicle parking brake.
  5. Verify the transmission is in Park for automatic transmissions and Neutral for manual transmissions.
  6. Start the engine and allow the engine to idle.
  7. Allow the engine to idle for the specified time.
Is the action complete?		 2 minutes Go to Step 3  -
3 
CAUTION: Refer to Road Test Caution
In order for the next group of tests to run, the vehicle must operate in the following conditions:
  1. Acceleration at part throttle to 89 km/h (55 mph) with this speed maintained until the engine reaches operating temperature. This may be up to 8 minutes depending on the start up coolant temperature.
  2. Continued operation under these conditions for an additional 6 minutes.
Is the action complete?		 - Go to Step 4  -
4 
CAUTION: Refer to Road Test Caution .
In order for the next group of tests to run, the vehicle must operate in the following conditions:
  1. Acceleration at part throttle to 72-89 km/h (45-55 mph) with this speed maintained for 2 minutes.
  2. Deceleration to 0 km/h (0 mph).
  3. Engine idling for 2 minutes while the following criteria is maintained:
    • The service brake is depressed.
    • The automatic transmission is in drive.
    • The manual transmission is in neutral with the clutch pedal depressed.
Is the action complete?		 - Go to Step 5  -
5
IMPORTANT: If only one test status indicates No, go to the I/M System DTC Table for the I/M System Set Procedure for the indicated system.
Observe the I/M System Status display with a scan tool.Did all of the I/M System Status indicators update to YES?		 - Go to Step 6  Go to Diagnostic Trouble Code (DTC) List - Vehicle
6 Observe the Emission Related DTC portion of the I/M System Status display with a scan tool.
Does the scan tool indicate any Emission Related DTCs set?		 - Go to Diagnostic Trouble Code (DTC) List - Vehicle System OK
scientia non olet · About LEMON Manuals