Body Control Module (BCM)
- ALC Status
-
The scan tool displays On/Off. When the ambient light sensor indicates low light level the body control module (BCM) will turn the automatic light control (ALC) ON and the scan tool will display On.
- Ambient Light Sensor
-
The scan tool displays Volts. The ambient light sensor voltage will vary depending on the outside lighting conditions.
- Backup Lamp Relay Cmd.
-
Automatic transmission only. The scan tool display On/Off. When the transmission is placed in the REVERSE position, the scan tool displays On.
- Battery Voltage Signal
-
The scan tool displays Volts. This is the current battery voltage at the BCM.
- BPP Sensor
-
The scan tool displays Volts. The varied voltage from the brake pedal position (BPP) sensor is displayed on the scan tool.
- BPPS Learn Home Position
-
The scan tool displays Counts. The brake pedal home position is displayed as Counts.
- BPPS Ratio
-
The scan tool displays Counts. The varied voltage from the brake pedal position (BPP) sensor is displayed on the scan tool as counts.
- BPPS Status
-
The scan tool displays Learned/Unlearned. If the BPP sensor is not programmed, the scan tool displays Unlearned.
- Day/Night Status
-
The scan tool displays Day/Night. When daylight conditions are present the scan tool will display day.
- DRL Status
-
The scan tool displays On/Off. When the ambient light sensor indicates outside light conditions are bright, the scan tool will display On indicating the daytime running lamps (DRLs) are active.
- Flash to Pass Switch
-
The scan tool displays Inactive/Active. When the flash to pass switch is placed in the OFF position, the scan tool displays Inactive.
- Front Fog Lamp Relay Command
-
The scan tool displays On/Off. When the fog lamp switch is placed in the ON position, the scan tool displays On.
- Front Fog Lamp Switch
-
The scan tool displays Inactive/Active. When the fog lamp switch is in the OFF position, the scan tool displays Off.
- Hazard Lamp Switch
-
The scan tool displays Off/On. When the hazard switch is placed in the ON position, the scan tool will display On.
- Headlamp OFF Switch
-
The scan tool displays On/Off. When the headlamp switch is placed in the OFF position, the scan tool displays OFF.
- Headlamp ON Switch
-
The scan tool displays On/Off. When the headlamp switch is placed in the ON position, the scan tool displays On.
- High Beam Relay Command
-
The scan tool displays On/Off. When the high beam headlamps are turned ON, the scan tool displays On.
- High Beam Select Switch
-
The scan tool displays Inactive/Active. When the high beam headlamps are turned ON, the scan tool displays Active.
- I/P Dimmer Switch
-
The scan tool displays Volts. When the instrument panel (I/P) dimmer switch is rotated from HIGH to LOW, the scan tool displays the change in Volts.
- Inadvertent Power Cmd.
-
The scan tool displays On/Off. When the inadvertent power is being commanded ON by the BCM, the scan tool displays On.
- Inadvertent Power Signal
-
The scan tool displays Inactive/Active. When the inadvertent power is being commanded ON by the BCM, the scan tool displays Active.
- Interior Light Command
-
The scan tool displays On/Off. When the interior courtesy lamps are ON, the scan tool will display On.
- Interior Lights Dimmed Command
-
The scan tool displays On/Off. When the interior courtesy lamps are being dimmed, the scan tool will display On.
- Left Turn Signal Switch
-
The scan tool displays Inactive/Active. When the turn signal switch is placed in the LEFT position, the scan tool displays Active.
- LF Turn/Hazard Lamp Command
-
The scan tool displays On/Off. When the turn signal is place in the LEFT position, the scan tool displays On.
- LF Turn Lamp/DRL Status
-
The scan tool displays On/Off. When the DRL lamps are commanded ON by the BCM or the turn signal switch is placed in the LEFT position, the scan tool displays On.
- Low Beam Relay Command
-
The scan tool displays On/Off. When the headlamp are turned ON, the scan tool displays On.
- LR Turn/Hazard Lamp Command
-
The scan tool displays On/Off. When the turn signal is place in the LEFT position, the scan tool displays On.
- LR Turn/Stop Lamp Status
-
The scan tool displays On/Off. When the LR turn/Stop lamps are commanded ON by the BCM or the turn signal switch is placed in the LEFT position, the scan tool displays On.
- Park Brake Switch
-
The scan tool displays Active/Inactive. When the park brake is applied the scan tool will display Active.
- Park Lamp Relay Cmd.
-
The scan tool displays On/Off. When the park lamps are turned ON, the scan tool will display On.
- Park Lamp Switch
-
The scan tool displays On/Off. When the park lamp switch is placed in the ON position, the scan tool will display On.
- RF Turn/Hazard Lamp Command
-
The scan tool displays On/Off. When the turn signal is place in the right position, the scan tool displays On.
- RF Turn Lamp/DRL Status
-
The scan tool displays On/Off. When the DRL lamps are commanded ON by the BCM or the turn signal switch is placed in the right position, the scan tool displays On.
- RR Turn/Hazard Lamp Command
-
The scan tool displays On/Off. When the turn signal switch is placed in the right position, the scan tool displays On.
- RR Turn/Stop Lamp Status
-
The scan tool displays On/Off. When the RR turn/Stop lamps are commanded ON by the BCM or the turn signal switch is placed in the right position, the scan tool displays On.
- Stop Lamp Relay Command
-
The scan tool displays On/Off. When the brakes are applied the scan tool displays On.