Torque Specifications
TORQUE SPECIFICATIONS
| Part Tightened | N.m | kgf.cm | ft.lbf |
|---|---|---|---|
| Transmission control cable assy at Body | 5.0 | 51 | 44 in.lbf |
| Floor shift lever assy at Floor | 12 | 122 | 9 |
| Wire harness clamp at Manual transaxle | 5.0 | 51 | 44 in.lbf |
| Ground cable at Engine mounting bracket LH | 26 | 260 | 19 |
| Air cleaner bracket at Manual transaxle | 19 | 195 | 14 |
| Clutch release cylinder at Flexible hose tube | 15 | 155 | 11 |
| Engine hanger No.1 at Engine | 40 | 408 | 29 |
| Front suspension member reinforcement set bolt | 47 | 479 | 35 |
| Front suspension crossmember at body Bolt A Bolt B |
70 116 |
714 1,183 |
52 86 |
| Engine mounting bracket LH at Manual transaxle | 64 | 653 | 47 |
| Engine mounting bracket RR at Manual transaxle Bolt A Bolt B |
64 18 |
653 180 |
47 13 |
| Engine mounting insulator LH at Engine mounting bracket LH | 49 | 500 | 36 |
| Engine mounting insulator RR at Engine mounting bracket RR | 64 | 653 | 47 |
| Starter assy at Manual transaxle | 37 | 380 | 27 |
| Starter assy at Starter wire | 9.8 | 100 | 87 in.lbf |
| Manual transaxle at Engine | 33 | 340 | 24 |
| Filler plug at Manual transaxle | 39 | 400 | 29 |
| Drain plug at Manual transaxle | 39 | 400 | 29 |
| Bearing lock plate at Front transaxle case | 11 | 115 | 8.3 |
| Oil receiver pipe No.1 at Manual transmission case | 17 | 175 | 13 |
| Oil receiver pipe No.2 at Manual transmission case | 17 | 175 | 13 |
| Reverse restrict pin plug at Manual transmission case | 13 | 130 | 9.3 |
| Manual transaxle case receiver at Manual transmission case | 11 | 115 | 8.3 |
| Gear shift fork No.1 at Gear shift fork shaft No.1 | 16 | 160 | 12 |
| Gear shift fork No.2 at Gear shift fork shaft No.2 | 16 | 160 | 12 |
| Gear shift head No.1 at Gear shift fork shaft No.2 | 16 | 160 | 12 |
| Reverse shift arm bracket assy at Front transaxle case | 17 | 175 | 13 |
| Manual transmission case at Front transaxle case bolt nut |
29 29 |
300 300 |
22 22 |
| Reverse idler gear shaft bolt at Manual transmission case | 29 | 300 | 22 |
| Lock ball assy No.2 at Manual transmission case | 39 | 400 | 29 |
| Shift detent ball at Manual transmission case | 22 | 224 | 16 |
| Shift detent ball at Front transaxle case | 22 | 224 | 16 |
| Bearing retainer rear at Manual transmission case | 27 | 280 | 20 |
| Gear shift fork No.3 at Gear shift fork shaft | 16 | 160 | 12 |
| Manual transmission output shaft rear set nut at output shaft | 118 | 1200 | 87 |
| Manual transmission case cover at Manual transmission case | 18 | 185 | 14 |
| Control shaft cover at Manual transmission case | 20 | 200 | 14 |
| Lock ball assy No.1 at Manual transmission case | 29 | 300 | 22 |
| Selecting bell crank assy at Manual transmission case | 25 | 250 | 18 |
| Floor shift control lever housing support bracket at Front transaxle case | 18 | 188 | 14 |
| Back-up lamp switch assy at Manual transmission case | 40 | 410 | 30 |
| Speedometer driven hole cover sub-assy at Manual transaxle | 11 | 115 | 8.3 |
| Release fork support at Front transaxle case | 37 | 375 | 25 |
| Clutch release cylinder assy at Manual transaxle | 12 | 120 | 9 |
| Manual transmission filler plug at Manual transaxle | 39 | 400 | 29 |
| Drain plug sub-assy at Manual transmission case | 39 | 400 | 29 |
| Selecting bell crank No.2 plate washer at Selecting bell crank | 12 | 120 | 9 |
| Front differential ring gear at Front differential case | 77 | 790 | 57 |