Front Seat Assembly: Reassembly

HINT:

• Use the same procedures for the RH side and LH side.
• The procedures listed below are for the LH side.

1. INSTALL SEAT POSITION AIRBAG SENSOR (for Driver Side)  ( INSTALLATION )
2. INSTALL SEAT SLIDE POSITION SENSOR PROTECTOR (for Driver Side) 
3. INSTALL VERTICAL ADJUSTER SPACER (for Driver Side) 
   1. Attach the claws to install the spacer.
4. INSTALL FRONT SEAT CUSHION SHIELD LOWER LH (for Driver Side) 
   1. Attach the claws to install the cushion shield.
5. INSTALL FRONT SEAT CUSHION SHIELD LOWER RH (for Driver Side) 
   1. Attach the claws to install the cushion shield.
6. INSTALL RECLINING ADJUSTER INSIDE COVER LH 
   1. Upper side:

      Install the inside cover with the screw.

   2. Lower side:

      Attach the clamp and install the inside cover with the screw.

7. INSTALL RECLINING ADJUSTER INSIDE COVER RH 
   1. Upper side:

      Install the inside cover with the screw.

   2. Lower side:

      Install the inside cover with the screw.

8. INSTALL FRONT SEATBACK COVER 
   NOTE:

   • Be careful not to damage the cover.
   • When installing the hog rings, avoid wrinkling the cover.
   1. Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.
   2. Install the seatback cover (with pad) to the seat adjuster.
   3. Install the 2 headrest supports.
      Fig 1: Identifying Seatback Cover To Seatback Pad With Hog Rings

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   4. w/ Front seat side airbag:

      Fully cover the airbag with the 2 seatback cover brackets. Then attach the hook and tighten the nut.

      Torque: 5.5 N*m (56 kgf*cm, 49 in.*lbf) 

      NOTE:

      • For vehicle with front seat side airbag, the seatback cover must be securely installed. Otherwise, the side airbag may not deploy properly.
      • Make sure that the strap is not twisted after installing the bracket.
      • Install the bracket securely.
        Fig 2: Identifying Front Seatback Cover Hook

        Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   5. Using hog ring pliers, install the seatback cover with new hog rings and attach the hooks.
9. INSTALL RECLINING REMOTE CONTROL BEZEL 
   1. Attach the 4 claws and install the bezel.
      Fig 3: Identifying Claws On Bezel

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
   2. Attach the claw to install the reclining adjuster release handle.
      Fig 4: Identifying Claw To Installing Reclining Adjuster Release Handle

      Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
10. INSTALL FRONT SEAT CUSHION COVER 
    NOTE:

    • Be careful not to damage the cover.
    • When installing the hog rings, avoid wrinkling the cover.
    1. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.
    2. Using hog ring pliers, install the seat cushion cover (with pad) to the seat adjuster with new hog rings and hooks.
    3. Passenger side:

       Connect the connector.

       Fig 5: Identifying Seatback Cover To Seatback Pad With Hog Rings

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
11. INSTALL FRONT SEAT CUSHION SHIELD INNER LH 
    1. Attach the 2 claws and clip to install the cushion shield.
    2. Install the screw.
12. INSTALL FRONT SEAT INNER BELT ASSEMBLY LH  ( INSTALLATION )
    Fig 6: Identifying Front Seat Cushion Shield Inner LH With Screw And Claw

    Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
13. INSTALL FRONT SEAT CUSHION SHIELD LH 
    1. Attach the 2 claws and clip to install the cushion shield.
    2. Install the screw.
       Fig 7: Identifying Front Seat Cushion Shield With Screws And Claws

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
14. INSTALL RECLINING ADJUSTER RELEASE HANDLE LH 
    1. Attach the claw to install the release handle.
15. INSTALL NO. 2 VERTICAL ADJUSTING HANDLE (for Driver Side) 
    1. Install the vertical adjusting handle with the 2 screws.
       Fig 8: Identifying Claw On Handle

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
    2. Attach the 3 claws to install the vertical seat adjuster knob cap.
       Fig 9: Identifying Claws On Vertical Seat Adjuster Knob Cap

       Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
16. INSTALL VERTICAL SEAT ADJUSTER KNOB LH (for Driver Side) 
    1. Install the knob with the snap ring.