LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Scion >> 2009 >> xB Standard >> Repair and Diagnosis >> External Pages >> Different car >> Section 38 (Cruise Control) >> Cruise Control System >> Data List / Active Test
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Data List / Active Test

WARNING: This page is about a different car, the 2008 Scion xB. However, it is still accessible from the selected car via links, so may be relevant.
  1. READ DATA LIST 

    HINT:

    Using an intelligent tester or Techstream to read the DATA LIST allows values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the DATA LIST information early in troubleshooting is one way to save diagnostic time.

    NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.
    1. Warm up the engine.
    2. Turn the ignition switch OFF.
    3. Connect an intelligent tester or Techstream to the DLC3.
    4. Turn the ignition switch ON.
    5. Turn the tester on.
    6. Enter the following menus:
      1. Intelligent tester - Select: DIAGNOSIS / OBD/ MOBD / CCS / DATA LIST.
      2. Techstream - Select: Powertrain / Cruise Control / Data List.
    7. According to the display on tester, read the "DATA LIST".
      1. Intelligent tester

        ECM (Cruise control) 

        DATA LIST

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        VEHICLE SPD Vehicle speed / mm 0 km/h (0 mph), max 255 km/h (158 mph) Actual vehicle speed -
        MEMORY SPD Cruise control memorized speed / mm 0 km/h (0 mph), max 200 km/h (125 mph) Actual stored vehicle speed -
        THROTTLE Throttle opening angle / mm 0°, max. 125° Actual demanded throttle angle -
        CRUISE CONTROL Cruise control system active condition / ON or OFF ON Cruise control activated
        OFF Cruise control deactivated        		 -
        MAIN SW (MAIN) Main switch signal (Main CPU) / ON or OFF ON Cruise control main switch on
        OFF Cruise control main switch off        		 -
        CCS READY M Cruise control system standby condition (Main CPU) / ON or OFF Each time main switch is pushed, ON is displayed and then OFF is displayed -
        CCS INDICATOR M Cruise indicator signal (Main CPU)/ON or OFF ON "CRUISE" on
        OFF "CRUISE" off        		 -
        CANCEL SW CANCEL switch signal / ON or OFF ON CANCEL switch on
        OFF CANCEL switch off        		 -
        SET/COAST SW -/SET switch signal / ON or OFF ON - (COAST) / SET switch on
        OFF - (COAST) / SET switch off        		 -
        RES/ACC SW +/RES switch signal / ON or OFF ON + (ACCEL) / RES (RESUME) switch on
        OFF + (ACCEL) / RES (RESUME) switch off        		 -
        STP LIGHT SW M Stop light switch signal (Main CPU) / ON or OFF ON Brake pedal depressed
        OFF: Brake pedal released        		 -
        CCS OPER STATUS Cruise control condition / ON or OFF ON Cruise control operated
        OFF Cruise control operation stopped        		 -
      2. Techstream

        Cruise control 

        DATA LIST

        Tester Display Measurement Item/Range Normal Condition Diagnostic Note
        CCS Vehicle Spd Vehicle speed / mm 0 km/h (0 mph), max. 255 km/h (158 mph) Actual vehicle speed -
        CCS Mein Vehicle Spd Cruise control memorized speed / mm 0 km/h (0 mph), max 200 km/h (125 mph) Actual stored vehicle speed -
        Throttle Opening Angle Throttle opening angle / mm 0°, max 125° Actual demanded throttle angle -
        Cruise Control Cruise control system active condition / ON or OFF ON Cruise control activated
        OFF Cruise control deactivated        		 -
        CCS Main SW M-CPU Main switch signal (Main CPU) / ON or OFF ON Cruise control main switch on
        OFF Cruise control main switch off        		 -
        CCS Ready M-CPU Cruise control system standby condition (Main CPU) / ON or OFF Each time main switch is pushed, ON is displayed and then OFF is displayed -
        CCS Indicator M-CPU Cruise indicator signal (Main CPU)/ON or OFF ON "CRUISE" on
        OFF "CRUISE" off        		 -
        Cancel Switch CANCEL switch signal / ON or OFF ON CANCEL switch on
        OFF CANCEL switch off        		 -
        SET/COAST Switch -/SET switch signal / ON or OFF ON: - (COAST) / SET switch on
        OFF - (COAST) / SET switch off        		 -
        RES/ACC Switch +/RES switch signal / ON or OFF ON + (ACCEL)/RES (RESUME) switch on
        OFF + (ACCEL)/RES (RESUME) switch off        		 -
        Stp Light SW M-CPU Stop light switch signal (Main CPU)/ON or OFF ON Brake pedal depressed
        OFF Brake pedal released        		 -
        Cruise Operation Status Cruise control condition / ON or OFF ON: Cruise control operated
        OFF Cruise control operation stopped        		 -
        # Codes Number of diagnosis codes/Mm 0, Max 255 - -
  2. PERFORM ACTIVE TEST 

    HINT:

    Using an intelligent tester or Techstream to perform ACTIVE TESTs allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing ACTIVE TESTs early in troubleshooting is one way to save diagnostic time. DATA LIST information can be displayed while performing ACTIVE TESTs.

    1. Warm up the engine.
    2. Turn the ignition switch OFF.
    3. Connect an intelligent tester or Techstream to the DLC3.
    4. Turn the ignition switch ON.
    5. Turn the tester on.
    6. Enter the following menus:
      1. Intelligent tester - Select: DIAGNOSIS / OBD/ MOBD / METER / ACTIVE TEST / ALL DATA.
      2. Techstream - Select: Body / Combination Meter/ Active Test.
    7. According to the display on tester, perform the "ACTIVE TEST".
      1. Intelligent tester

        COMBINATION METER 

        DATA LIST

        Tester Display Test Part Control Range Diagnostic Note
        CRUISE INDIC Turns CRUISE main indicator light ON/OFF -
      2. Techstream

        Combination meter 

        DATA LIST

        Tester Display Test Part Control Range Diagnostic Note
        Indicate Lamp Cruise Turns CRUISE main indicator light ON/OFF -
scientia non olet · About LEMON Manuals