LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Subaru >> 2006 >> Baja Base, Standard >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - Engine (Diagnostics) (H4SO) >> Compulsory Valve Operation Check Mode >> Operation
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Compulsory Valve Operation Check Mode: Operation

  1. Prepare Subaru Select Monitor kit. < Ref. to PREPARATION TOOL , General Description. >
    Fig 1: Identifying Subaru Select Monitor Kit
    G04998013Courtesy of SUBARU OF AMERICA, INC.
  2. Connect diagnosis cable to Subaru Select Monitor.
  3. Insert cartridge into Subaru Select Monitor. < Ref. to PREPARATION TOOL , General Description. >
    Fig 2: Inserting Cartridge Into Subaru Select Monitor
    G04988744Courtesy of SUBARU OF AMERICA, INC.
  4. Connect test mode connector (A) at the lower portion of instrument panel (on the driver's side), to the side of the center console box.
    Fig 3: Identifying Test Mode Connector
    G04988750Courtesy of SUBARU OF AMERICA, INC.
  5. Connect Subaru Select Monitor to data link connector.
    1. Connect Subaru Select Monitor to data link connector (A) located in the lower portion of the instrument panel (on the driver's side).
      Fig 4: Identifying Data Link Connector
      G04988742Courtesy of SUBARU OF AMERICA, INC.
    2. Connect diagnosis cable to data link connector.
    CAUTION: Do not connect scan tools except for Subaru Select Monitor and general scan tool.
  6. Turn ignition switch to ON (engine OFF) and Subaru Select Monitor switch to ON.
    Fig 5: Identifying Power Switch
    G04988760Courtesy of SUBARU OF AMERICA, INC.
  7. On the «Main Menu» display screen, select the {2. Each System Check} and press the [YES] key.
  8. On the «System Selection Menu» display screen, select the {Engine Control System} and press the [YES] key.
  9. Press the [YES] key after displayed the information of engine type.
  10. On the «Engine Diagnosis» display screen, select the {System Operation Check Mode} and press the [YES] key.
  11. On the «System Operation Check Mode» display screen, select the {Actuator ON/OFF Operation} and press the [YES] key.
  12. Select the desired compulsory actuator on the «Actuator ON/OFF Operation» display screen and press the [YES] key.
  13. Pressing the [NO] key completes the compulsory operation check mode. The display will then return to the «Actuator ON/OFF Operation» screen.
    • A list of the support data is shown in the following table.
      SUPPORT DATA LIST

      Contents Display
      Compulsory fuel pump relay operation check Fuel Pump Relay
      Compulsory radiator fan relay operation check Radiator Fan Relay
      Compulsory air conditioning relay operation check A/C Compressor Relay
      Compulsory purge control solenoid valve operation check CPC Solenoid Valve
      Compulsory air assist injector solenoid valve operation check AAI Solenoid Valve
      Compulsory fuel tank pressure control solenoid valve operation check PCV Solenoid Valve
      Compulsory drain valve operation check Vent Control Solenoid Valve
      Fuel tank sensor control valve operation check Fuel Tank Sensor Control Valve
      NOTE:
      • The following parts will be displayed but not functional.
        ASV SOLENOID VALVE REFERENCE

        Display
        ASV Solenoid Valve
        FICD Solenoid
        Pressure Switching Sol. 1
        Pressure Switching Sol. 2
        Turbo Pressure Control Solenoid
        Exhaust Bypass Valve
        EGR Valve Solenoid
      • For detailed operation procedure, refer to the Subaru Select Monitor Operation Manual.
scientia non olet · About LEMON Manuals