Led Operation Mode For Engine
- On the «Main Menu» display screen, select the {Each System Check} and press the [YES] key.
- On the «System Selection Menu» display screen, select the {Engine Control System} and press the [YES] key.
- Press the [YES] key after displayed the information of engine type.
- On the «Engine Diagnosis» display screen, select the {Current Data Display & Save} and press the [YES] key.
- On the «Data Display Menu» display screen, select the {Data & LED Display} and press the [YES] key.
- Using the scroll key, move the display screen up or down until the desired data is shown.
- A list of the support data is shown in the following table.
SUPPORT DATA LIST
| Contents | Display | Message | LED "ON" requirements |
|---|---|---|---|
| Ignition switch signal | Ignition Switch | ON or OFF | When ignition switch is turned ON. |
| Test mode connector signal | Test Mode Signal | ON or OFF | When test mode connector is connected. |
| Neutral position switch signal | Neutral Position Switch | ON or OFF | When neutral position signal is entered. |
| Air conditioning switch signal | A/C Switch | ON or OFF | When air conditioning switch is turned ON. |
| Air conditioning relay signal | A/C Relay | ON or OFF | When air conditioning relay is in function. |
| Radiator main fan relay signal | Radiator Fan Relay #1 | ON or OFF | When radiator main fan relay is in function. |
| Fuel pump relay signal | Fuel Pump Relay | ON or OFF | When fuel pump relay is in function. |
| Knocking signal | Knocking Signal | ON or OFF | When knocking signal is entered. |
| Radiator sub fan relay signal | Radiator Fan Relay #2 | ON or OFF | When radiator sub fan relay is in function. |
| Engine torque control signal #1 | Torque Control Signal #1 | ON or OFF | When engine torque control signal 1 is entered. |
| Engine torque control signal #2 | Torque Control Signal #2 | ON or OFF | When engine torque control signal 2 is entered. |
| Engine torque control permission signal | Torque Control Permit | ON or OFF | When engine torque control permission signal is entered. |
| Front oxygen (A/F) sensor rich signal | Front O2 Rich Signal #1 | ON or OFF | When front oxygen (A/F) sensor mixture ratio is rich. |
| Rear oxygen sensor rich signal | Rear O2 Rich Signal | ON or OFF | When rear oxygen sensor mixture ratio is rich. |
| Pressure control solenoid valve | PCV Solenoid Valve | ON or OFF | When pressure control solenoid valve is in function. |
| Drain valve | Vent. Solenoid Valve | ON or OFF | When drain valve is in function. |
| Starter switch signal | Starter Switch Signal | ON or OFF | When starter switch signal is entered. |
| Idle switch signal | Idle Switch Signal | ON or OFF | When idle switch signal is entered. |
| Crankshaft position sensor signal | Crankshaft Position Sig. | ON or OFF | When crankshaft position sensor signal is entered. |
| Camshaft position sensor signal | Camshaft Position Sig. | ON or OFF | When camshaft position sensor signal is entered. |
| AT/MT discriminating terminal | AT vehicle ID signal | AT models/ MT models | AT models: ON |
| Rear defogger switch signal | Rear Defogger Switch | ON or OFF | Rear defogger switch: ON |
| Blower fan switch signal | Blower Fan Switch | ON or OFF | Blower fan switch: ON |
| Small light switch signal | Light Switch | ON or OFF | Small light switch: ON |
| Power steering switch signal | P/S switch | ON or OFF | When power steering switch signal is entered. |
| Fuel tank sensor control valve | Tank Sensor Cntl. Valve | ON or OFF | When fuel tank sensor control valve signal is entered. |
| Air assist injector solenoid valve signal | Assist Air Sol. Valve | ON or OFF | When air assist injector solenoid valve is activated. |
NOTE:
For detailed operation procedure, refer to the Subaru Select Monitor Operation Manual.