Read Current Data For Engine (OBD Mode)
- On the «Main Menu» display screen, select the {Each System Check} and press the [YES] key.
- On the «System Selection Menu» display screen, select the {Engine Control System} and press the [YES] key.
- Press the [YES] key after the information of engine type has been displayed.
- On the «Engine Diagnosis» display screen, select the {OBD System} and press the [YES] key.
- On the «OBD Menu» display screen, select the {Current Data Display/Save}, and then press the [YES] key.
- On the «Display Menu» screen, select the {Data Display} and press the [YES] key.
- Using the scroll key, scroll the display screen up or down until the desired data is shown.
- A list of the support data is shown in the following table.
SUPPORT DATA SPECIFICATION CHART
| Contents | Display | Unit of measure | Note (at idling) |
|---|---|---|---|
| Number of diagnosis code | Number of DTC | - | 0 |
| Condition of malfunction indicator light | Ml (MIL) | - | OFF |
| Misfire monitoring | Misfire monitoring | - | Complete |
| Fuel system monitoring | Fuel system monitoring | - | Complete |
| Component monitoring | Component monitoring | - | Complete |
| Catalyst diagnosis | Catalyst Diagnosis | - | Incomplete |
| Heated catalyst | Heated catalyst | - | No |
| Evaporative purge system | Evaporative purge system | - | Incomplete |
| Secondary air system | Secondary air system | - | No |
| A/C system refrigerant | A/C system refrigerant | - | No |
| Oxygen sensor | Oxygen sensor | - | Incomplete |
| O2 heater diagnosis | O2 Heater Diagnosis | - | Complete |
| Test of EGR system | EGR system | - | Incomplete |
| A/F control #1 | A/F Control #1 | - | Normal CLOSE |
| Load | Load | % | 23.0% |
| Engine coolant temperature signal | Coolant Temp. | °C or °F | 92°C or 198°F |
| A/F correction value #1 | A/F Correction Value #1 | % | -0.8% |
| A/F learning value #1 | A/F Learning Value #1 | % | +0.0% |
| Intake manifold absolute pressure | Mani. Absolute Pressure | mmHg, kPa, inHg or psig | 211 mmHg, 28.1 kPa, 8.31 inHg or 4.08 psig |
| Engine speed signal | Engine Speed | rpm | 700 rpm |
| Vehicle speed signal | Vehicle Speed | km/h or MPH | 0 km/h or 0 MPH |
| Ignition timing #1 | Ignition timing #1 | ° | +16.0° |
| Intake air temperature signal | Intake Air Temp. | °C or & deg;F | 36°C or 97°F |
| Intake air amount | Mass Air Flow | g/s or lb/m | 2.7 g/s or 0.36 lb/m |
| Throttle opening angle signal | Throttle Opening Angle | % | 13% |
| Oxygen sensor (Bank 1 Sensor 2) | Oxygen Sensor #12 | V | 0.7 V |
| A/F correction (Bank 1 Sensor 2) | A/F Correction #12 | % | 0.0% |
| OBD system | OBD system | - | CARB-OBD2 |
| Front oxygen (A/F) sensor (Bank 1 Sensor 1) | Oxygen Sensor #11 | - | Support |
| Oxygen sensor (Bank 1 Sensor 2) | Oxygen Sensor #12 | - | Support |
| Front oxygen (A/F) sensor (Bank 1 Sensor 1) | A/F sensor #11 | - | 1.001 |
| Front oxygen (A/F) sensor (Bank 1 Sensor 1) | A/F sensor #11 | V | 2.79 V |
| Front oxygen (A/F) sensor (Bank 1 Sensor 1) | A/F sensor #11 | - | 1.001 |
| Front oxygen (A/F) sensor (Bank 1 Sensor 1) | A/F sensor #11 | mA | 0.00 mA |
NOTE:
For detailed operation procedure, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL ".