LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Subaru >> 2006 >> Forester XT Limited, Automatic >> Repair and Diagnosis >> Engine Performance >> System >> Engine Controls - Engine (Diagnostics) (H4DOTC) >> Compulsory Valve Operation Check Mode >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Compulsory Valve Operation Check Mode: Procedure

  1. Prepare the Subaru Select Monitor kit. <Ref. to PREPARATION TOOL , GENERAL DESCRIPTION. >
    Fig 1: Identifying Subaru Select Monitor Kit
    G04998013Courtesy of SUBARU OF AMERICA, INC.
  2. Connect the diagnosis cable to Subaru Select Monitor.
  3. Insert the cartridge to Subaru Select Monitor. <Ref. to PREPARATION TOOL , GENERAL DESCRIPTION. >
    Fig 2: Inserting Cartridge Into Subaru Select Monitor
    G04998014Courtesy of SUBARU OF AMERICA, INC.
  4. Connect the test mode connector (A) located at the lower portion of instrument panel (on the driver's side).
    Fig 3: Identifying Test Mode Connector
    G04999931Courtesy of SUBARU OF AMERICA, INC.
  5. Connect the Subaru Select Monitor to data link connector located in the lower portion of the instrument panel (on the driver's side).
    Fig 4: Locating Data Link Connector
    G05002012Courtesy of SUBARU OF AMERICA, INC.
    CAUTION: Do not connect any scan tools except the Subaru Select Monitor or the general scan tool.
  6. Turn the ignition switch to ON (engine OFF) and Subaru Select Monitor switch to ON.
    Fig 5: Identifying Subaru Select Monitor Switch
    G05002030Courtesy of SUBARU OF AMERICA, INC.
  7. On the «Main Menu» display screen, select {Each System Check} and press the [YES] key.
  8. On the «System Selection Menu» display screen, select {Engine Control System} and press the [YES] key.
  9. Press the [YES] key after the information of engine type has been displayed.
  10. On the «Engine Diagnosis» display screen, select {System Operation Check Mode} and press the [YES] key.
  11. On the «System Operation Check Mode» display screen, select {Actuator ON/OFF Operation} and press the [YES] key.
  12. Select the desired compulsory actuator on the «Actuator ON/OFF Operation» display screen and press the [YES] key.
  13. Pressing the [NO] key completes the compulsory operation check mode. The display will then return to the «Actuator ON/OFF Operation» screen.
    • A list of the support data is shown in the following table.
SUPPORT DATA

DESCRIPTION Display
Compulsory fuel pump relay operation check Fuel Pump
Compulsory radiator fan relay operation check Radiator Fan Relay
Compulsory air conditioning relay operation check A/C Compressor Relay
Compulsory purge control solenoid valve operation check CPC Solenoid
Compulsory pressure control solenoid valve operation check PCV Solenoid
Compulsory drain valve operation check Vent. Control Solenoid
Compulsory wastegate control solenoid valve operation check Wastegate control solenoid
Secondary air combination valve 1 compulsory operation check Secondary Air Combination Valve 1
Secondary air combination valve 2 compulsory operation check Secondary Air Combination Valve 2
Secondary air pump relay compulsory operation check Secondary air pump relay
NOTE:
  • The following parts will be displayed but not functional because they are not installed on the vehicle.
    DISPLAY

    Display
    EGR Solenoid
    ASV Solenoid
    FICD Solenoid
    Pressure Switching Sol.1
    Pressure Switching Sol.2
    AAI Solenoid
    Exhaust Bypass Valve Control Permit Flag
  • For detailed operation procedure, refer to the "SUBARU SELECT MONITOR OPERATION MANUAL".
scientia non olet · About LEMON Manuals