Special Tool

WARNING: This page is about a different variant/trim than selected.

TOOL NUMBER	DESCRIPTION	REMARKS
498575400	OIL PRESSURE GAUGE ASSY	Used for measuring oil pressure.
498897200	OIL PRESSURE ADAPTER	Used together with oil pump cover installed on when measuring line pressure.
498897800	OIL PRESSURE ADAPTER SET	Used for measuring the transfer clutch pressure.
498277200	STOPPER SET	Used for removing and installing the automatic transmission assembly. Used for preventing the torque converter from dropping off.
398527700	PULLER ASSY	Used for removing the extension oil seal. Used for removing the front differential side retainer bearing outer race.
498057300	INSTALLER	Used for installing the extension oil seal.
498077000	REMOVER	Used for removing the front differential taper roller bearing. Used for installing the center differential ball bearing.
18658AA020	WRENCH COMPL RETAINER	Used for removing and installing the differential side retainer. WRENCH COMPL RETAINER (18630AA010) can also be used.
398487700	DRIFT	Used for installing the front differential taper roller bearing.
498255400	PLATE	Used for measuring the backlash of hypoid gear.
498247001	MAGNET BASE	Used for measuring the gear backlash. Used together with DIAL GAUGE (498247100).
498247100	DIAL GAUGE	Used for measuring the gear backlash. Used together with MAGNET BASE (498247001).
498517000	REPLACER	Used for removing the drive pinion shaft front roller bearing.
499787700	WRENCH	Used for removing and installing the drive pinion shaft lock nut. Used for adjusting the front differential hypoid gear backlash.
398643600	GAUGE	Used for measuring total end play, extension end play and drive pinion height.
398744300	PISTON GUIDE	Used for measuring height from mating surface of the main case to pressure plate.
499737100	PULLER SET	Used for removing the reduction driven gear assembly. Used together with GEAR HOLDER (18680AA010) and SUPPORT PULLER (18766AA000).
498077600	REMOVER	Used for removing the center differential ball bearing.
18667AA010	HOLDER	Used for removing and installing the drive pinion lock nut. Used as a handle to rotate gear when checking tooth contact. Used for adjusting preload on the front differential side bearing.
1B022XU0	SUBARU SELECT MONITOR III KIT	Used for troubleshooting the electrical system.
18675AA000	DIFFERENTIAL SIDE OIL SEAL INSTALLER	Used for installing the differential side retainer oil seal.
18654AA000	INSTALLER	Used for installing the reduction driven gear ball bearing.
28399SA010	OIL SEAL PROTECTOR	Used for protecting oil seal when installing front drive shaft.
18763AA000	COMPRESSOR SHAFT	Used for disassembling and assembling front brake clutch and reverse brake clutch.
18765AA000	COMPRESSOR SUPPORT	Used for disassembling and assembling front brake clutch and reverse brake clutch.
18676AA020	TORX® WRENCH	Used for removing and installing the torque converter case.
18854AA000	ANGLE GAUGE	Used for tightening parking support. Used for tightening the drive plate.
498497100	CRANKSHAFT STOPPER	Used for stopping the drive plate rotation when removing and installing the drive plate.
498077300	REMOVER	Used for removing ball bearing of reduction driven gear.
499587100	OIL SEAL INSTALLER	Used for installing the converter case oil seal.
499787500	ADAPTER	Used for installing and removing drive pinion shaft lock nut. Used for adjusting preload on the front differential side bearing.
499575400	GAUGE	Used for adjusting the total end play (selecting the reduction driven gear shim).
18762AA000	COMPRESSOR SPECIAL TOOL	Used for disassembling and assembling front brake clutch and reverse brake clutch. Used together with COMPRESSOR SHAFT (18763AA000) and COMPRESSOR SUPPORT (18765AA000).
499755602	PRESS	Used for installing the parking gear.
18680AA010	GEAR HOLDER	Used for removing the reduction driven gear assembly. (2-piece set)
18766AA000	SUPPORT PULLER	Used for removing the reduction driven gear assembly.
18767AA000	REMOVER	Used for removing the parking gear.
41099AJ010	SPECIAL TOOL H6	Used for removing and installing transmission. For H6 engine.
18360AA020	HANGER	Used for removing and installing transmission. For H6 engine.
99099AJ000	ENGINE HANGER	Used for removing and installing transmission. Used together with CHAIN BALANCER (99099AJ010) and sling chain (general tool).
99099AJ010	CHAIN BALANCER	Used for removing and installing transmission. Used together with ENGINE HANGER (99099AJ000) and sling chain (general tool). Used to hang the engine while balancing it with the sling chain inserted in this tool.