Read Current Data: List
WARNING: This page is about a different car, the 2013 Subaru Forester. However, it is still accessible from the selected car via links, so may be relevant.
| Items to be displayed | Unit of measure | Remarks | Note |
|---|---|---|---|
| BATT voltage (control) | 9 - 16 V | Body integrated unit input value | Always |
| BATT voltage (BACKUP) | 9 - 16 V | Body integrated unit input value | Always |
| IG power supply voltage | 9 - 16 V | Body integrated unit input value | Ignition switch ON |
| ACC voltage | 9 - 16 V | Body integrated unit input value | Ignition switch ACC |
| Illumination VR Voltage | 0 - 5 V | Body integrated unit input value | Input value from illumination volume |
| Illumi. output d-ratio | 0 - 100% | Body integrated unit output value | Small light ON Illumination volume is other than bright. |
| Ambient Temperature | -40 - 87.5°C | CAN data input value | Ignition switch ON |
| Fuel level voltage | 0 - 10 V | Body integrated unit input value | Ignition switch ON |
| Fuel level resistance | 0 - 102.3 Ω | Body integrated unit input value | Ignition switch ON |
| key-lock solenoid V | 6 - 15 V | Body integrated unit output value | Key warning switch ON, other than parking range Ignition ON |
| number of regist. | 0 - 4 | Number of keyless key registered | Number of transmitter registered is displayed |
| Front Wheel Speed | km/h | CAN data input value | Reception from VDC module |
| VDC/ABS latest f-code | DTC display (Temporarily) | CAN data input value | It is normal when DTC is not been input even if this code is displayed. Received from VDC (displayed by hexadecimal number system) |
| Blower fan steps | 0 - 2 levels | CAN data input value | 0: OFF, 1: 1 level, 2: 2 levels or more Reception from air conditioner ECM |
| Fuel level resistance 2 | 0 - 102.3 Ω | CAN data output value | Reception from body integrated unit |
| Fuel consumption | cc/s | CAN data input value | Reception from ECM and transmission to center monitor |
| Coolant Temp. | -40 - 130°C | CAN data input value | Reception from ECM |
| Vehicle longitudinal G | m/s2 | CAN data input value | Reception from VDC module |
| SPORT Shift Stages | 0 - 7 levels | CAN data input value | (0: Light OFF; 1 - 5: Gear display; 6: Fail; 7: ATF temperature High/Low) Reception from TCM |
| Shift Position | 0 - 7 levels | CAN data input value | 0: 1, 1: 2, 2: 3, 3: 4, 4: D, 5: N, 6: R, 7: P shift position (8 indicates no input) 8 is displayed in manual mode Reception from TCM |
| VDC/ABS condition | 0 - 4 | CAN data input value | Reception from VDC module |
| Destination Code | 0 - 16 | CAN data input value | Reception from combination meter |
| Touch SW | 0 - 64 | CAN data input value | Reception from navigation module |
| key-lock warning SW | ON/OFF | Body integrated unit input value | ON when ignition key inserted |
| Stop Light Switch | ON/OFF | Body integrated unit input value | ON when brake pedal is depressed |
| Front fog lamp SW input | ON/OFF | Body integrated unit input value | When front fog light switch is ON |
| Driver's door SW input | ON/OFF | Body integrated unit input value | ON when driver's door is open |
| P-door SW input | ON/OFF | Body integrated unit input value | ON when passenger's door is open |
| Rear right door SW input | ON/OFF | Body integrated unit input value | ON when rear right door is open |
| Rear left door SW input | ON/OFF | Body integrated unit input value | ON when rear left door is open |
| R Gate SW input | ON/OFF | Body integrated unit input value | ON when rear gate/trunk open |
| Manual lock SW input | ON/OFF | Body integrated unit input value | Manual lock switch ON |
| Manual unlock SW input | ON/OFF | Body integrated unit input value | Manual unlock switch ON |
| Bright SW input | ON/OFF | Body integrated unit input value | ON when bright switch is ON |
| P SW | ON/OFF | Body integrated unit input value | ON when shift range is in parking Shift lever P switch signal |
| MT Reverse Switch | ON/OFF | Body integrated unit input value | Shift lever is at reverse position |
| R wiper ON SW input | ON/OFF | Body integrated unit input value | Rear wiper switch ON |
| R wiper INT SW input | ON/OFF | Body integrated unit input value | Rear wiper switch (INT ON) |
| R washer SW input | ON/OFF | Body integrated unit input value | Rear washer switch ON |
| wiper deicer SW input | ON/OFF | Body integrated unit input value | Rear defogger switch ON |
| Rear Defogger SW | ON/OFF | Body integrated unit input value | |
| Driver's Seat SW input | ON/OFF | Body integrated unit input value | Driver's seat buckle switch ON |
| P seatbelt SW input | ON/OFF | Body integrated unit input value | Passenger's seat occupied and buckle switch ON |
| Fr wiper input | ON/OFF | Body integrated unit input value | ON when front wiper is operating |
| Parking Brake Switch Input | ON/OFF | Body integrated unit input value | ON when parking brake locked |
| R gate lock status SW input | ON/OFF | Body integrated unit inner memory value | Displays door lock/unlock state, ON when locked |
| R Gate Release SW input | ON/OFF | Body integrated unit input value | When rear gate opener button is ON |
| Rr Defogger output | ON/OFF | Body integrated unit output value | ON when rear defogger relay is operating |
| lock actuat. LOCK output | ON/OFF | Body integrated unit output value | ON when LOCK signal is output |
| All seat UNLOCK output | ON/OFF | Body integrated unit output value | ON when unlock signal is output |
| D-seat UNLOCK output | ON/OFF | Body integrated unit output value | ON when unlock signal is output |
| R gate/trunk UNLK output | ON/OFF | Body integrated unit output value | ON when rear gate/trunk unlock signal is output |
| R wiper output | ON/OFF | Body integrated unit output value | ON when rear wiper motor is operating |
| Shift Lock Solenoid | ON/OFF | Body integrated unit output value | ON when shift lock solenoid is operating (only AT) |
| Key locking output | ON/OFF | Body integrated unit output value | With ignition switch ON and in other than the shift P range, with key in switch ON |
| wiper deicer output | ON/OFF | Body integrated unit output value | ON when wiper deicer relay is operating |
| Hazard Output | ON/OFF | Body integrated unit output value | ON when answer-back signal is received or when emergency light (answer-back) is operating |
| Keyless Buzzer Output | ON/OFF | Body integrated unit output value | ON when lock/unlock signal is received |
| Horn Output | ON/OFF | Body integrated unit output value | ON when security warning is operating |
| D-belt warning light O/P | ON/OFF | CAN data output value | ON when ignition switch is turned to ON, and buckle switch is turned off |
| P-belt warning light O/P | ON/OFF | Body integrated unit output value | ON when ignition switch is turned to ON, occupant is seated, and buckle switch is turned off |
| Illumination lamp O/P | ON/OFF | Body integrated unit output value | ON when illumination is illuminated |
| Room lamp output | ON/OFF | Body integrated unit output value | When one of the doors is open |
| key illumi. lamp o/p | ON/OFF | Body integrated unit output value | ON when key illumination light is illuminated |
| Immobilizer lamp output | ON/OFF | Body integrated unit output value | ON when immobilizer pilot light blinks |
| Keyless operation 1 | Regist./Normal | Body integrated unit input value | When keyless is registered |
| Keyless operation 2 | Deletion/Normal | Body integrated unit input value | When keyless registration is deleted |
| CC Main Lamp | ON/OFF | CAN data input value | Cruise control switch ON Reception from ECM and transmission to combination meter |
| CC Set Lamp | ON/OFF | CAN data input value | ON when cruise control vehicle speed is set Reception from ECM and transmission to combination meter |
| SPORT Lamp | ON/OFF | CAN data input value | SPORT mode switch ON Reception from TCM and transmission to combination meter (only AT) |
| SPORT Blink | Blink/OFF | CAN data input value | Blinks when there is an AT failure Reception from TCM and transmission to combination meter (only AT) |
| ATF Temperature Lamp | ON/OFF | CAN data input value | When ATF temperature rise (only AT) |
| ATF Blink | Blink/OFF | CAN data input value | Blinks when there is an AT failure Reception from TCM and transmission to combination meter (only AT) |
| ECO Lamp (AT) | ON/OFF | CAN data input value | Not applicable |
| ECO Lamp (MT) | ON/OFF | CAN data input value | Not applicable |
| Tire diameter abnormal 1 | ON/OFF | CAN data input value | Lit when FWD fuse is connected (4AT only) |
| Tire diameter abnormal 2 | Blink/OFF | CAN data input value | Blinks when the difference in rotation between front and rear wheels is 4% or more Reception from TCM and transmission to combination meter (only AT) |
| Shift Up Indication | UP/OFF | CAN data input value | ON when shift lever up-operation is possible (only AT) |
| Shift Down Indication | DOWN/OFF | CAN data input value | ON when shift lever down-operation is possible (only AT) |
| SPORT Shift (buzzer 1) | ON/OFF | CAN data input value | ON while the shift change prohibited warning buzzer is operating Reception from TCM and transmission to combination meter (only AT) |
| SPORT Shift (buzzer 2) | ON/OFF | CAN data input value | ON when the ATF high temperature warning buzzer is operating Reception from TCM and transmission to combination meter (only AT) |
| ABS/VDC Judging | ABS/VDC | CAN data input value | Transmission from vehicle dynamic control (VDC) to high speed control module |
| Small Light SW | ON/OFF | CAN data output value | ON when small light is illuminated |
| Headlamp | ON/OFF | CAN data output value | When headlight LO is ON |
| High Beam | ON/OFF | CAN data output value | When headlight HI is ON |
| km/mile display | mile/km | CAN data input value | Unit of distance received from meter |
| Large diameter tire | large Tire/Others | CAN data output value | Large tire when the standard tire is 18 in Reception from combination meter |
| Number of cylinders | 4 Cylinder/6 Cylinder | CAN data input value | Display engine equipped |
| Cam shaft specification | SOHC/DOHC | CAN data input value | Display engine equipped |
| Turbo | TURBO/Without turbo | CAN data input value | Display engine equipped |
| E/G displacement (2.5L) | 2.5 L/OFF | CAN data input value | Display engine equipped |
| E/G displacement (3.0L) | 3.0 L/OFF | CAN data input value | Display engine equipped |
| AT Vehicle ID Signal | ON/OFF | CAN data input value | Display transmission equipped |
| Blower fan information | ON/OFF | CAN data input value | ON when blower fan is operating (always OFF for auto A/C equipped models) |
| Smart judging flag | Smart System/Other than Smart System | CAN data output value | Smart when integrated unit judges as a model with Smart |
| Diesel judging flag | Diesel/Other than Diesel | CAN data output value | Display diesel/other than diesel |
| Turbo judging flag | Without turbo/TURBO | CAN data output value | Display engine equipped |
| AT type judging flag | 4AT/5AT | CAN data output value | Display transmission equipped |
| CVT judging flag | CVT/Other than CVT | CAN data output value | Display CVT judging |
| Center display failure | OK/NG | CAN data input value | NG when there is a center display failure Reception from center display (NAVI monitor) |
| NAVI Failure | OK/NG | CAN data input value | NG when there is a navigation system failure Reception from Center Display |
| IE Bus failure | Can not use | CAN data input value | Reception from Center Display |
| Auto A/C failure | OK/NG | CAN data input value | NG when there is a failure in auto air conditioning system Reception from auto A/C module |
| EBD Warning Light | ON/OFF | CAN data input value | OK when EBD warning light is illuminated Reception from VDC/ABS and transmission to combination meter |
| ABS Warning Light | ON/OFF | CAN data input value | OK when ABS warning light is illuminated Reception from VDC/ABS and transmission to combination meter |
| VDC OFF flag | ON/OFF | CAN data input value | Vehicle dynamics control OFF SW is ON Reception from VDC/ABS and transmission to combination meter |
| VDC/ABS OK B | OK/NG | CAN data input value | NG when there is an error in VDC/ABS system Reception from VDC/ABS |
| Lighting I Switch Input | ON/OFF | Body integrated unit input value | ON when lighting switch illumination is ON |
| Lighting II Switch Input | ON/OFF | Body integrated unit input value | ON when lighting switch headlight is ON |
| Dimmer Hi Switch Input | ON/OFF | Body integrated unit input value | ON when dimmer switch is Hi beam position |
| Dimmer Pass Switch Input | ON/OFF | Body integrated unit input value | ON when dimmer switch is passing position |
| Lighting I Lamp Output | ON/OFF | Body integrated unit output value | ON when small light is illuminated |
| Lighting II Lamp Output | ON/OFF | Body integrated unit output value | ON when headlight is illuminated |
| Lighting Hi Lamp Output | ON/OFF | Body integrated unit output value | ON when Hi beam is illuminated |
| Front Fog Lamp Output | ON/OFF | Body integrated unit output value | ON when front fog light is ON. |
| DRL Cancel Output | ON/OFF | Body integrated unit output value | ON when lighting switch is "Headlight ON" and dimmer switch is "Hi beam" or "Passing" position |
| Power Supply Tr | ON/OFF | Body integrated unit output value | ON when lighting switch is "Head" position without inserting key in key cylinder |
| Spot map lamp output | ON/OFF | Body integrated unit output value | ON when one of the doors is open (except for tail gate) |
| Eco switch information | ON/OFF | CAN data output value | Not applicable |
| Off delay time | OFF, Short, Normal, Long | Body integrated unit setting items | Customize setting |
| Check engine' warning lamp output | ON, OFF, Blink 1, Blink 2, Blink 3 | Body integrated unit output value | Warning light is activated |
| Rr defogger op. mode | Continuous/Normal | Body integrated unit setting items | Customize setting |
| Security Alarm Setup | ON/OFF | Body integrated unit setting items | Customize setting |
| Impact Sensor Setup | ON/OFF | Body integrated unit setting items | Customize setting |
| Alarm delay setup | ON/OFF | Body integrated unit setting items | Customize setting |
| Lockout prevention | ON/OFF | Body integrated unit setting items | Customize setting |
| Impact sensor | ON/OFF | Body integrated unit setting items | Customize setting |
| Buzzer beeping setup | ON/OFF | Body integrated unit setting items | Customize setting |
| Hazard light setup | ON/OFF | Body integrated unit setting items | Customize setting |
| Buzzer setting | ON/OFF | Body integrated unit setting items | Customize setting |
| Auto locking | ON/OFF | Body integrated unit setting items | Customize setting |
| Passive Alarm | ON/OFF | Body integrated unit setting items | Customize setting |
| Door open warning | ON/OFF | Body integrated unit setting items | Customize setting |
| Dome Light Alarm Setting | ON/OFF | Body integrated unit setting items | Customize setting |
| Map Light Setting | ON/OFF | Body integrated unit setting items | Customize setting |
| Belt Warning Switch | ON/OFF | Body integrated unit setting items | Customize setting |
| Map lamp 30 sec off record | ON/OFF | Body integrated unit setting items | Customize setting |
| A/C ECM setting | ON/OFF | Body integrated unit setting items | Customize setting |
| wiperdeicer | ON/OFF | Body integrated unit setting items | Customize setting |
| Sedan/Wagon Setting | Sedan/Wagon | Body integrated unit setting items | Customize setting |
| MT/AT Setting | MT/AT | Body integrated unit setting items | Customize setting |
| 6MT Setting 6MT/Other than | 6MT | Body integrated unit setting items | Customize setting |
| Destination Setting | 0 - 16 | Body integrated unit setting items | - |
| Factory initial setting | Factory/Market | Body integrated unit setting items | Customize setting |
NOTE:
For detailed operation procedures, refer to
"PC application help for Subaru Select Monitor".