LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Subaru >> 2015 >> WRX Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 149 (Body Control System (Diagnostics)) >> User Customizing >> Operation
April 5, 2026: LEMON Manuals is launched! Read the announcement.

User Customizing: Operation

WARNING: This page is about a different car, the 2016 Subaru Outback and 2016 Subaru Legacy. However, it is still accessible from the selected car via links, so may be relevant.
  1. On «Start» display, select «Diagnosis».
  2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».
  3. On «Main Menu» display, select «Each System».
  4. On «Select System» display, select «Body Control» and then select «Enter».
  5. On «Select Function» display, select «Customize».
    NOTE:
    • If not equipped (depending on destination area or vehicle equipment condition), customizing is not possible.
    • For detailed operation procedures, refer to "Application help".

    List of User Customizing item

    Item Initial setting value Setting value Note
    Off delay time 30 Sec OFF
    10 Sec
    20 Sec
    30 Sec    		 Room light off delay time can be selected.
    Auto Light Sensitivity Adjustment Sensitive Dull
    Normal
    Sensitive
    Very sensitive    		 Sensitivity of the automatic lighting can be adjusted.
    Lane change signal setting ON ON
    OFF    		 ON: One-touch blinker function operates.
    OFF: One-touch blinker function does not operate.
    Rear wiper auto setting OFF (U0, U4, U5 models)
    ON: (C0, C5 models)    		 ON
    OFF    		 ON: Rear wiper operates in sync with the reverse shift.
    OFF: Rear wiper does not operate in sync with the reverse shift.
    Driver's Door Unlock Setting Selection Selection ALL Selection: When the touch sensor (unlock) on the driver's side is touched, only the driver's door is unlocked. When the touch sensor (unlock) on the passenger's side is touched, all doors are unlocked.
    ALL: When the touch sensor (unlock) on the driver's side is touched, all doors are unlocked. When the touch sensor (unlock) on the passenger's side is touched, all doors are unlocked.
    Rear Gate Unlock Setting Selection Selection ALL Selection: When the rear gate opener button is pressed, only the rear gate is unlocked.
    ALL: When the rear gate opener button is pressed, all doors are unlocked.
    Wiper link Auto Light Setup ON ON
    OFF    		 ON: Wiper interlock auto light function is activated.
    OFF: Wiper interlock auto light function is deactivated.
    High Beam Assist Function - ((1)) ON
    OFF    		 Set to ON for models with high beam assist.
    Head Lamp Low Beam Specification - ((1)) Halogen
    HID
    LED    		 Set according to the headlight type.
    Head Lamp High Beam Specification - ((1)) Halogen
    HID
    LED    		 Set according to the headlight type.
    High Beam Assist Current Setting - ((1)) ON
    OFF    		 Set to ON for models with high beam.
    Rear defogger operation mode Normal Normal
    Continuous    		 Normal: Automatically stops in 15 minutes after the switch is turned to ON.
    Continuous: Repeats the cycle of 15-minute active condition and 2-minute inactive condition until the switch is turned to OFF.
    Security Alarm Setup ON ON
    OFF    		 ON: Warning function (hazard, horn) is activated.
    OFF: Warning function (hazard, horn) is deactivated.
    Impact Sensor Setup ON ON
    OFF    		 ON: Impact sensor is activated.
    OFF: Impact sensor is deactivated. (Set to "OFF" in models without the impact sensor.)
    Alarm delay setup ON ON
    OFF    		 ON: The alarm monitor starts 30 seconds after the keyless lock operation.
    OFF: The alarm monitor starts immediately after the keyless lock operation.
    Lockout prevention ON ON
    OFF    		 ON: Key lockout prevention function is activated. (The function does not operate if safety knob is locked by hand.)
    OFF: Key lockout prevention function is deactivated.
    Impact sensor OFF ON
    OFF    		 ON: Vehicle is controlled in impact sensor equipped mode. (Make sure to set to "OFF" for models without the impact sensor. When set to "ON", hazard, horn or siren become activated by keyless lock (alarm monitor start).)
    OFF: Vehicle is controlled in no impact sensor mode.
    Buzzer sounding setting ON ON
    OFF    		 ON: Buzzer sounds when lock/unlock is selected by keyless entry system.
    OFF: Buzzer does not sound when lock/unlock is selected by keyless entry system.
    Abnormal warning lamp flashing setting ON ON
    OFF    		 ON: Hazard blinks when lock/unlock is selected by keyless entry system.
    OFF: Hazard does not blink when lock/unlock is selected by keyless entry system.
    Initial keyless setting - -
    Execution    		 -
    Initial button setting - -
    Execution    		 -
    Initial Security setting - -
    Execution    		 -
    Door open warning ON ON
    OFF    		 ON: If a door stays half shut for 20 minutes, interior lighting linked with the door such as room light, map light, luggage room light, trunk room light and key ring illumination go off to prevent battery run-out.
    OFF: Room light, map light, luggage room light, trunk room light, key ring illumination and door warning light remain lit.
    Dome Light Alarm Setting OFF ON
    OFF    		 ON: Room light illumination is interlocked with the alarm.
    OFF: Room light illumination is not interlocked with the alarm.
    Welcome Light (Exit) 30 Sec OFF
    30 Sec
    60 Sec
    90 Sec    		 Lighting time length of the welcome lighting (exiting) function can be set.
    Welcome Light Off Delay Time (Approaching) 30 Sec OFF
    30 Sec
    60 Sec
    90 Sec    		 Lighting time length of the welcome lighting (approaching) function can be set.
    Keyless Buzzer Volume 5 1 - 7 Buzzer volume can be set.
    Auto Dimmer Cancel setting 3 0 (OFF)
    Least 2
    Normal 4
    Most    		 Auto dimmer cancel sensitivity can be set.
    NOTE:
    (1) Customization item according to the actual vehicle equipment
  6. When the setting is complete, see «Data monitor» to make sure that the alterations are consistent with the actual equipment on the vehicle.
    CAUTION:
    • The above settings must match the actual vehicle equipment.
    • Do not change settings except for setting above while setting the functions.
    • Be sure not to change Factory initial setting except when installing a new body integrated unit.
scientia non olet · About LEMON Manuals