LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Subaru >> 2017 >> WRX Base >> Repair and Diagnosis >> External Pages >> Different car >> Section 17 (Brake System) >> Brake Pedal >> Installation >> Mt Model
April 5, 2026: LEMON Manuals is launched! Read the announcement.

Mt Model

WARNING: This page is about a different car, the 2022 Subaru WRX. However, it is still accessible from the selected car via links, so may be relevant.
CAUTION:

Before handling the airbag system components, refer to "CAUTION" of "General Description" in "AIRBAG SYSTEM". Ref. to  AIRBAG SYSTEM>GENERAL DESCRIPTION>CAUTION  . 

  1. Install the pedal assembly.

    Tightening torque: 

    18 N.m (1.8 kgf-m, 13.3 ft-lb)

  2. Install the operating rod to the pedal COMPL brake.
    1. Apply a thin coat of grease to the new clevis pin.

      Preparation items: 

      Grease: NIPPON GREASE NIGTIGHT LTS No. 2 or equivalent

      G14602272Courtesy of SUBARU OF AMERICA, INC.
    2. Using a clevis pin and a snap pin, install the operating rod to the pedal COMPL brake.
  3. Install the stop light switch assembly. Ref. to BRAKE>STOP LIGHT SWITCH>INSTALLATION .
  4. Connect each connector.
  5. Install the column assembly steering. Ref. to POWER ASSISTED SYSTEM (POWER STEERING)>STEERING COLUMN>INSTALLATION .
  6. Install the universal joint assembly steering. Ref. to POWER ASSISTED SYSTEM (POWER STEERING)>UNIVERSAL JOINT>INSTALLATION .
    CAUTION:
    • Always install the universal joint assembly steering after installing the steering column to avoid damage to the universal joint assembly steering. 
    • Be sure to follow the tightening order and tightening torque of the universal joint assembly steering to avoid the steering effort from becoming heavy. After confirming that the steering column position is in the neutral position, tighten the universal joint assembly steering. 
  7. Install the duct foot driver. Ref. to AIR CONDITIONER>AIR VENT DUCT>INSTALLATION>FOOT DUCT .
  8. Install the knee airbag module. Ref. to AIRBAG SYSTEM>KNEE AIRBAG MODULE>INSTALLATION .
  9. Install the cover LWR driver. Ref. to EXTERIOR/INTERIOR TRIM>INSTRUMENT PANEL LOWER COVER>INSTALLATION .
  10. Install the bolt and the clutch pipe B to the two-way connector.

    Tightening torque: 

    Flange bolt: 7.5 N.m (0.8 kgf-m, 5.5 ft-lb)

    Clutch pipe B: 15.5 N.m (1.6 kgf-m, 11.4 ft-lb)

  11. Install the reservoir hose assembly.
  12. Add the recommended brake fluid. Ref. to CLUTCH SYSTEM>CLUTCH FLUID .
  13. After bleeding air from the clutch system, ensure that no brake fluid leaks and the clutch operates properly. Ref. to CLUTCH SYSTEM>AIR BLEEDING>PROCEDURE .
  14. Adjust the clutch pedal. Ref. to CLUTCH SYSTEM>CLUTCH PEDAL>ADJUSTMENT .
  15. Install the intercooler. Ref. to INTAKE (INDUCTION) (H4DOTC)>INTERCOOLER>INSTALLATION .
  16. Connect the ground terminal to battery sensor. Ref. to REPAIR CONTENTS>NOTE>BATTERY .
  17. Check the clutch start system.
  18. Check that the brake light operate properly.
  19. Check the brake pedal. Ref. to BRAKE>BRAKE PEDAL>INSPECTION .
scientia non olet · About LEMON Manuals