LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Subaru >> 2019 >> WRX Base >> Repair and Diagnosis >> Accessories & Equipment >> Communication Devices >> Body Control System (Diagnostics) >> User Customizing >> Operation
April 5, 2026: LEMON Manuals is launched! Read the announcement.

User Customizing: Operation

  1. On «Start» display, select «Diagnosis».
  2. On «Vehicle selection» display, input the target vehicle information and select «Confirmed».
  3. On «Main Menu» display, select «Each System».
  4. On «Select System» display, select «Body Control» and then select «Enter».
  5. On «Select Function» display, select «Customize».
    NOTE: For detailed operation procedures, refer to "Application help".
    USER CUSTOMIZING ITEM LIST

    Data Initial setting value Customize setting Remarks
    Off delay time 30 Seconds OFF Room light off delay time can be selected.
    10 Seconds
    20 Seconds
    30 Seconds
    Auto Light Sensitivity Adjustment Normal Dull Slow response
    Normal Standard
    Sensitive Quick response
    Very sensitive Fairly quick response
    Remote Trunk Open/Power Rear Gate Open Function (ON/OFF) ON ON Trunk/power rear gate open function is activated by operating the keyless transmitter.
    OFF Trunk/power rear gate open function is not activated by operating the keyless transmitter.
    Lane Change Signal Setting OFF ON One-touch blinker control is performed.
    OFF One-touch blinker control is not performed.
    Rear wiper auto setting OFF ON Existence of rear wiper linked with reverse operation can be set.
    OFF
    TPMS Setting - ((1)) TPMS Set to "ON" for model with TPMS.
    No TPMS
    Driver's Door Unlock Setting Select Select When the touch sensor (unlock) on the driver's side is touched, only the driver's door is unlocked. When the touch sensor (unlock) on the passenger's side is touched, all doors are unlocked.
    ALL When the touch sensor (unlock) on the driver's side is touched, all doors are unlocked. When the touch sensor (unlock) on the passenger's side is touched, all doors are unlocked.
    Rear Gate Unlock Setting Select Select When the rear gate opener button is pressed, only the rear gate is unlocked.
    ALL When the rear gate opener button is pressed, all doors are unlocked.
    Daytime Running Light (DRL) Setting for North America - ((1)) High Beam Dimming System Set according to the daytime running light source type.
    Alternate DRL System
    Wiper Link Auto Light Setup ON ON Wiper interlock auto light function is activated.
    OFF Wiper interlock auto light function is deactivated.
    Steering Responsive Fog Lamp Setting - ((1)) ON SRF control is performed.
    OFF SRF control is not performed.
    Head Lamp Low Beam Specification -((1)) Halogen Set according to the headlight type.
    HID
    LED
    Head Lamp High Beam Specification - ((1)) Halogen
    HID
    LED
    High Beam Assist Current Setting - ((1)) ON Set to ON for models with HBA.
    OFF
    High Beam Assist Function Setting (mirror/EyeSight) - ((1)) No HBA Set according to the HBA type.
    EyeSight HBA
    mirror HBA
    Rear defogger operation mode Normal Normal Automatically stops in 15 minutes after the switch is turned to ON.
    Continuous Repeats activated for 15 minutes and deactivated for 2 minutes until the switch is turned to OFF.
    Security Alarm Setup OFF ON Security alarm (hazard, horn or siren) becomes activated.
    OFF Security alarm becomes deactivated.
    Impact Sensor Setup OFF ON Workable when the Impact Sensor Setup is set to "ON". Impact sensor function becomes activated.
    OFF Impact sensor function becomes deactivated. (Be sure to set to "OFF" for models without sensors.)
    Alarm delay setup ON   After the keyless lock operation, the alarm monitor starts after the following delay time has passed.
    ON Delay time is 30 seconds.
    OFF Delay time is 0 seconds.
    Lockout prevention ON ON key lockout prevention function is activated. (The function does not operate if safety knob is locked by hand.)
    OFF Key lockout prevention function is deactivated.
    Impact sensor OFF ON Vehicle is controlled in impact sensor equipped mode. (Make sure to set to "OFF" for models without the impact sensor. When "ON", hazard, horn or siren become activated by keyless lock (alarm monitor start).)
    OFF Vehicle is controlled in impact sensor non-equipped mode.
    Buzzer sounding setting ON ON Buzzer operates when lock/unlock is selected by keyless entry system operation.
    OFF Buzzer does not operate when lock/unlock is selected by keyless entry system operation.
    Abnormal warning lamp flashing setting ON ON Hazard blinks when lock/unlock is selected by keyless entry system operation.
    OFF Hazard is not interlocked when lock/unlock is selected by keyless entry system operation.
    Initial keyless setting - - -
    Operate -
    Initial button setting - - -
    Operate -
    Passive Alarm OFF ON  
    OFF  
    Door open warning ON ON If a door stays half shut for 20 minutes, room light, map light, and key ring illumination related to doors are turned off to prevent battery run-out.
    OFF Room light, map light, key illumination and door warning light are not turned off.
    Dome Light Alarm Setting OFF ON Room light illuminates interlocking with alarm.
    OFF Room light does not illuminate interlocking with alarm.
    Welcome Light Off Delay Time (Exiting) 30 Seconds OFF/30 Sec/60 Sec/90 Sec Length of the lighting time can be set.
    Welcome Light Off Delay Time (Approaching) 30 Seconds OFF/30 Sec/60 Sec/90 Sec Length of the lighting time can be set.
    Keyless Buzzer Volume 5 1 - 7 Buzzer volume can be set.
    Auto Dimmer Cancel setting 3 OFF Auto dimmer cancel sensitivity can be set.
    Dull
    Less
    Normal
    More
    Most
    (1) Customization item according to the actual vehicle equipment
  6. When the setting is complete, see «Data monitor» to make sure that the alterations are consistent with the actual equipment on the vehicle.
    CAUTION:
    • the above settings must match the actual vehicle equipment.
    • Do not change settings except for setting above while setting the functions.
    • Be sure not to change the factory initial setting except when installing a new body integrated unit.
    NOTE: For detailed operation procedures, refer to "Application help".
scientia non olet · About LEMON Manuals