Electrical Specification
- Models without EyeSightNOTE:
- Terminal numbers in VDC Control Module & H/U connector (on the control module side) are shown in the figure.
- When the connector is removed from the VDC Control Module & H/U, the brake warning light (EBD warning light), ABS warning light, VDC warning light & VDC indicator light, VDC OFF indicator light, and the hill start assist warning light illuminate.
Content Terminal No. (+) - (-) Input/Output signal Measured value and measuring conditions Power supply 6 - 13 10 - 15 V when the ignition switch is ON. ABS wheel speed sensor Front LH wheel Power supply 36 - 13 0 - 18 V when the ignition switch is ON. Signal 37 7 - 14 mA: Rectangle waveform Front RH wheel Power supply 27 - 13 0 - 18 V when the ignition switch is ON. Signal 26 7 - 14 mA: Rectangle waveform Rear LH wheel Power supply 29 - 13 0 - 18 V when the ignition switch is ON. Signal 30 7 - 14 mA: Rectangle waveform Rear RH wheel Power supply 34 - 13 0 - 18 V when the ignition switch is ON. Signal 33 7 - 14 mA: Rectangle waveform Valve relay power supply 25 - 13 10 - 15 V Motor relay power supply 1 - 13 10 - 15 V Stop light switch 2 - 13 1.5 V or less when the stop light is OFF; 10 - 15 V when the stop light is ON. Vehicle speed output signal 5 0 ←→ 12 V pulse VDC OFF switch 20 - 13 1 Ω or less when the OFF switch is "ON"; 1 MΩ or more when the switch is "OFF". CAN communication line (H) 11 Pulse signal CAN communication line (L) 10 Pulse signal Ground 13 - - Models with EyeSight
NOTE:
- Terminal numbers in VDC Control Module & H/U connector (on the control module side) are shown in the figure.
- When the connector is removed from the VDC Control Module & H/U, the brake warning light (EBD warning light), ABS warning light, VDC warning light & VDC operation indicator light and VDC OFF indicator light illuminate.
| Content | Terminal No. (+) - (-) | Input/Output signal | ||
|---|---|---|---|---|
| Measured value and measuring conditions | ||||
| Power supply | 35 - 14 | 10 - 15 V when the ignition switch is ON. | ||
| ABS wheel speed sensor | Front LH wheel | Power supply | 9 - 14 | 0 - 18 V when the ignition switch is ON. |
| Signal | 8 | 7 - 14 mA: Rectangle waveform | ||
| Front RH wheel | Power supply | 5 - 14 | 0 - 18 V when the ignition switch is ON. | |
| Signal | 4 | 7 - 14 mA: Rectangle waveform | ||
| Rear LH wheel | Power supply | 7 - 14 | 0 - 18 V when the ignition switch is ON. | |
| Signal | 6 | 7 - 14 mA: Rectangle waveform | ||
| Rear RH wheel | Power supply | 11 - 14 | 0 - 18 V when the ignition switch is ON. | |
| Signal | 10 | 7 - 14 mA: Rectangle waveform | ||
| Valve relay power supply | 30 - 14 | 10 - 15 V | ||
| Motor relay power supply | 1 - 14 | 10 - 15 V | ||
| Stop light switch | 15 - 14 | 1.5 V or less when the stop light is OFF; 10 - 15 V when the stop light is ON. | ||
| Stop light relay power supply | 25 - 14 | 10 - 15 V when the ignition switch is ON. | ||
| Vehicle speed output signal | 22 | 0 ←→ 12 V pulse | ||
| VDC OFF switch | 31 - 14 | 1 Ω or less when the OFF switch is "ON"; 1 MΩ or more when the switch is "OFF". | ||
| Parking brake switch | 17 | Pulse signal | ||
| Parking brake switch | 18 | Pulse signal | ||
| Parking brake switch | 19 | Pulse signal | ||
| Parking brake switch | 24 | Pulse signal | ||
| Rear brake caliper RH | 2 - 3 | Pulse signal | ||
| Rear brake caliper LH | 12 - 13 | Pulse signal | ||
| AVH switch | 36 - 14 | 10 - 15 V when the AVH switch is ON | ||
| Electronic parking brake operation indicator light | 33 - 14 | 0 V when the light is on; 10 - 15 V when the light is off. | ||
| CAN communication line (H) | 42 | Pulse signal | ||
| CAN communication line (L) | 43 | Pulse signal | ||
| Ground | 14 | - | ||