Common Specifications & Procedures
BRZ COMMON SPECIFICATIONS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | SPECIFICATION | ||
| Torque | See Torque Specifications in applicable text under COMPONENTS WITH TORQUE SPECIFICATIONS | ||
| Axle Shaft Nut (Front) | N/A | ||
| Axle Shaft Nut (Rear) | 190 N.m (19.4 kgf-m, 140.1 ft-lb) | ||
| Battery | BATTERY | ||
| Brakes | |||
| Bleeding Sequence | AIR BLEEDING | ||
| Disc Brakes | |||
| Front | FRONT DISC BRAKE | ||
| Rear | REAR DISC BRAKE | ||
| Torque | See Torque Specifications in text under COMPONENTS WITH TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR | ||
| Torque | See Torque Specifications in text under COMPONENTS WITH TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | INSTALLATION | ||
| Belt Routing | INSTALLATION | ||
| Engine Cooling | |||
| General Service Specifications | SPECIFICATION | ||
| Radiator Cap Pressure | 14-18 psi (0.95-1.25 kg/cm2 ) | ||
| Thermostat R & I | THERMOSTAT | ||
| Water Pump R & I | WATER PUMP | ||
| Engine Mechanical | |||
| Compression | |||
| (at 200-300 RPM) | 1, 390 - 1, 735 kPa (14 - 18 kgf/cm2 , 202 - 252 psi) | ||
| Oil Pressure | |||
| While idling (AT model) | 44 kPa (0.4 kg/cm2 , 6 psi) or more | ||
| At 3, 000 RPM (AT model) | 234 kPa (2.4 kg/cm2 , 34 psi) or more | ||
| While idling (MT model) | 39 kPa (0.4 kg/cm2 , 6 psi) or more | ||
| At 3, 000 RPM (MT model) | 234 kPa (2.4 kg/cm2 , 34 psi) or more | ||
| Overhaul | SPECIFICATION | ||
| Torque | See Torque Specifications in text for appropriate items under COMPONENTS WITH TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE. | ||
| Flywheel/Flex Plate (Drive Plate) Torque | |||
| 4 Cylinder | 95 N.m (9.7 kgf-m, 70.1 ft-lb) | ||
| Fuel System | |||
| Fuel Pressure Test Procedure | INSPECTION | ||
| Fuel Filter Location | Fuel filter is attached to Fuel Pump Unit located in fuel tank. | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Engine is equipped with Coil-On-Plug ignition. | ||
| Ignition Wires (Routing) | Engine is equipped with Coil-On-Plug ignition. | ||
| Spark Plug | DENSO: ZXE27HBR8 / Gap: 0.7 - 0.8 mm (0.028 - 0.031 in.) / Tightening Torque: 17 N.m (1.7 kgf-m, 12.5 ft-lb) | ||
| Starting | |||
| Starter | STARTER | ||
| Torque | 50 N.m (5.1 kgf-m, 36.9 ft-lb) | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | WHEEL ALIGNMENT | ||
| Rear | WHEEL ALIGNMENT | ||
| Torque | |||
| Front | See Torque Specifications in text under COMPONENTS WITH TORQUE SPECIFICATIONS | ||
| Rear | See Torque Specifications in text under COMPONENTS WITH TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 120 N.m (12.2 kgf-m, 88.5 ft-lb) | ||