Specifications Index
AVEO, SWIFT+ (CANADIAN) & WAVE (CANADIAN) SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT SYSTEM CAPACITIES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 221 lb ft (300 N.m) | ||
| Battery | BATTERY USAGE | ||
| Brakes | |||
| Bleeding Sequence | HYDRAULIC BRAKE SYSTEM BLEEDING (MANUAL) | ||
| Disc Brakes | DISC BRAKE COMPONENT SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS |
||
| Drum Brakes | DRUM BRAKE COMPONENT SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS |
||
| Charging | |||
| Generator | GENERATOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Drive belt uses auto-tensioner | ||
| Belt Routing | See figure under REMOVAL PROCEDURE | ||
| Engine Cooling | |||
| General Service Specifications | NA | ||
| Radiator Cap Pressure | Pressure is stamped on pressure cap | ||
| Thermostat R & I | |||
| 1.4L & 1.6L (DOHC) | THERMOSTAT REPLACEMENT (1.4L/1.6L DOHC) | ||
| Water Pump R & I | NA | ||
| Engine Mechanical | |||
| 1.6L | |||
| Compression | ENGINE COMPRESSION TEST | ||
| Oil pressure | NA | ||
| Overhaul | ENGINE MECHANICAL SPECIFICATIONS | ||
| Torque | ENGINE MECHANICAL SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive PlateTorque | |||
| 1.5L & 1.6L | |||
| Flexplate | 44 ft. lbs. (60 N.m) | ||
| Flywheel | First Step 26 ft. lbs. (35 N.m) Second Step + an additional 30 degrees Final Step + an additional 15 degrees |
||
| Fuel System | |||
| Pressure Specification | 1.6L 55-62 psi (380-427 kPa) | ||
| Fuel Pressure Test Procedure | 1.6L See Fuel Pressure Gage Installation and Removal and FUEL SYSTEM DIAGNOSIS | ||
| Fuel Filter Location | 1.6L The fuel filter is contained in the fuel sender assembly inside the fuel tank | ||
| Fuel Filter R & I | 1.6L FUEL SENDER ASSEMBLY REPLACEMENT | ||
| Ignition | |||
| Firing Order & Cylinder Identification | |||
| All Engines | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | 1.6L 2,000-12,000 ohms | ||
| Ignition Wires (Routing) | |||
| 1.6L | NA | ||
| Spark Plug | |||
| 1.6L (Type Woojin - BKR6E-11) | |||
| Gap | 0.039-0.043 in (1.0-1.1 mm) | ||
| Torque | 18 lb ft (25 N.m) | ||
| Starting | |||
| Starter | STARTER MOTOR USAGE | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFICATIONS | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque (Steel & Aluminumn) | 88 ft. lbs. (120 N.m) | ||