Common Specs & Procedures Index
SX4 SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Manual | |||
| Service | Refer to appropriate article text under REPAIR INSTRUCTIONS . | ||
| Torque | SPECIFICATIONS | ||
| Automatic | |||
| Service | GENERAL DESCRIPTION | ||
| Torque | Information is not available. | ||
| Axle Nut/Hub Nut | |||
| Front | 147.5 ft. lbs. (200 N.m) | ||
| Rear | 129 ft. lbs. (175 N.m) | ||
| Battery | CHARGING SYSTEM SPECIFICATIONS | ||
| Brakes | |||
| Bleeding Sequence | AIR BLEEDING OF BRAKE SYSTEM | ||
| Disc Brakes | For front brakes, refer to appropriate component INSPECTION procedure under REPAIR INSTRUCTIONS . For rear disc brakes, refer to appropriate component INSPECTION procedure under REPAIR INSTRUCTIONS . | ||
| Drum Brakes | For rear drum brakes, refer to appropriate component INSPECTION procedure under REPAIR INSTRUCTIONS . | ||
| Torque | For front brakes, refer to SPECIFICATIONS . For rear disc brakes, refer to SPECIFICATIONS . For rear drum brakes, refer to SPECIFICATIONS . For parking brake, refer to SPECIFICATIONS . For brake control system, refer to SPECIFICATIONS . For ABS, refer to SPECIFICATIONS . For electronic stability control, refer to SPECIFICATIONS . | ||
| Charging | |||
| Generator | CHARGING SYSTEM SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | ACCESSORY DRIVE BELT TENSION INSPECTION | ||
| Belt Routing | Refer to figure under ACCESSORY DRIVE BELT REMOVAL AND INSTALLATION . | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM REFILLING | ||
| Radiator Cap Pressure | 108 kPa (1.1 kgf/cm2 , 15.6 psi) | ||
| Thermostat R & I | THERMOSTAT REMOVAL AND INSTALLATION | ||
| Water Pump R & I | WATER PUMP REMOVAL AND INSTALLATION | ||
| Engine Mechanical | |||
| Compression | COMPRESSION CHECK | ||
| Oil Pressure | More than 300 - 500 kPa (3.1 - 5.1 kgf/cm2 , 43.5 - 72.5 psi) at 4,000 RPM | ||
| Overhaul | Refer to appropriate component TABLE in ENGINE MECHANICAL article. | ||
| Torque | For engine component specifications, refer to SPECIFICATIONS . For lubrication component specifications, refer to SPECIFICATIONS . | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flexplate Torque | 52 ft. lbs. (70 N.m) | ||
| Fuel System | |||
| Fuel Filter Location | FUEL PUMP DESCRIPTION | ||
| Pressure Specifications | Standard: 360 - 400 kPa (3.7 - 4.1 kgf/cm2 , 52.2 - 58.0 psi) (With fuel pump operating and engine stopped) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE CHECK | ||
| Fuel Pressure Release Procedure | FUEL PRESSURE RELIEF PROCEDURE | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | N/A | ||
| Spark Plugs | |||
| Type | Non-EVAP-leak-check model: DENSO K16HPR-U11 (Nickel): EVAP-leak-check model: NGK SILFR5A11 (Iridium) | ||
| Gap | Standard: 1.0 - 1.1 mm (0.040 - 0.043 in.) | ||
| Torque | 25 N.m (2.5 kg-m, 18.5 lb. ft.) | ||
| Starting | |||
| Starter | CRANKING SYSTEM SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | FRONT WHEEL ALIGNMENT INSPECTION AND ADJUSTMENT | ||
| Rear | REAR WHEEL ALIGNMENT INSPECTION | ||
| Torque | For front suspension, refer to SPECIFICATIONS . For rear suspension, refer to SPECIFICATIONS . | ||
| Wheel & Tire | |||
| Lug Nut Torque | 61.5 ft. lbs. (85 N.m) | ||