Wheel Alignment Specifications & Adjustment Procedures: Sienna: Specifications
Wheel Alignment Specifications (Sienna)
| Cold tire inflation pressure (Normal driving) | P205/70R1595S | Front, Rear | 240 kPa (2.4 kgf/cm2 , 35 bar or psi) | |||||||||
| P215/65R1595S | Front, Rear | 220 kPa (2.2 kgf/cm2
, 32 bar or psi)(1) 240 kPa (2.4 kgf/cm2 ,35 bar or psi)(2) |
||||||||||
| Cold tire inflation pressure (Trailer towing) | P205/70R1595S | Front, Rear | 240 kPa (2.4 kgf/cm2 ,35 bar or psi) | |||||||||
| P215/65R1595S | Front, Rear | 240 kPa (2.4 kgf/cm2 ,35 bar or psi) | ||||||||||
| Front wheel alignment | Vehicle height | 205/70R15 | Front(3) | 230 mm (9.06 in.) | ||||||||
| Rear(4) | 324 mm (12.76 in.) | |||||||||||
| 215/65R15 | Front(3) | 226 mm (8.90 in.) | ||||||||||
| Rear(4) | 320 mm (12.60 in.) | |||||||||||
| Camber | -0°32' ± 45' (-0.5° ± 0.75°) | |||||||||||
| Left - right error | 45' (0.75°) or less | |||||||||||
| Caster | 1°32' ± 45' (1.53° ± 0.75°) | |||||||||||
| Left-right error | 45' (0.75°) or less | |||||||||||
| Steering axis inclination | 12°35' ± 45' (12.58° ± 0.75°) | |||||||||||
| Toe-in (Total) | 0°16' ± 12' (0.27° ± 0.2°) 2.6 ± 2 mm (0.10 ± 0.08 in.) |
|||||||||||
| Rack end length difference | 1.5 mm (0.059 in.) or less | |||||||||||
| Wheel angle | Inside wheel | 34°19' ± 1° (34.32° ± 1°) | ||||||||||
| Outside wheel < Reference > | 30° 19' (30.32°) | |||||||||||
| Rear wheel alignment | Camber | -0°55' + 45' (-0.92° ± 0.75°) | ||||||||||
| Left-right error | 45' (0.75°) or less | |||||||||||
| Toe-in (Total) | 0°13' ± 18' (0.22° ± 0.30°) | |||||||||||
| 2.2 ± 3 mm (0.09 ± 0.12 in.) | ||||||||||||
| Front axle | Axle bearing backlash | Maximum | 0.05 mm (0.0020 in.) | |||||||||
| Axle hub deviation | Maximum | 0.05 mm (0.0020 in.) | ||||||||||
| Front drive shaft | Drive shaft standard length | LH | 586.0 ± 2.0 mm (23.071 ± 0.079 in.) | |||||||||
| RH | 881.6 ± 2.0 mm (34.709 ± 0.079 in.) | |||||||||||
| Front suspension | Lower ball joint turning torque | 1.0 - 3.4 N.m (10 - 35 kgf.cm, 8.7 - 30 in..lbf) | ||||||||||
| Stabilizer bar link turning torque | 0.05 -1.0 N.m (0.5-10 kgf.cm, 0.4 - 8.7 in..lbf) | |||||||||||
| Rear axle | Axle bearing backlash | Maximum | 0.05 mm (0.0020 in.) | |||||||||
| Axle hub deviation | Maximum | 0.07 mm (0.0028 in.) | ||||||||||
Measure from the ground to the center of the front side lower suspension arm mounting bolt.
Measure from the ground to the center of the axle beam bushing. |
||||||||||||