Data List / Active Test

WARNING: This page is about a different car, the 2008 Toyota Camry Solara. However, it is still accessible from the selected car via links, so may be relevant.

READ DATA LIST

HINT:

Using Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

Connect Techstream to the DLC3.
Turn the ignition switch to the ON position.
Turn the Techstream main switch on.
Enter the following menu items: Powertrain / Cruise Control / Data List.
Read the Data List addording to the display on Techstream.

DATA LIST

Tester Display	Measurement Item/Range	Normal Condition	Diagnostic Note
CCS VEHICLE SPD	Vehicle speed / min.: 0 km/h (0mph), max.: 255 km/h (158 mph)	Actual vehicle speed	-
CCS MEM VEHICLE SPD	Memory vehicle speed / min.: 0 km/h (0 mph), max.: 200 km/h (125 mph)	Actual stored vehicle speed	-
THROTTLE OPENING ANGLE	Throttle opening angle / min.: 0°, max.: 125°	Actual required throttle opening	-
CRUISE CONTROL	Cruise control system active condition / ON or OFF	ON: Cruise control activated OFF: Cruise control inactivated	-
MAIN SW M-CPU	Main SW signal (Main CPU)/ ON or OFF	ON: Main SW ON (Pushed on) OFF: Main SW OFF (Pushed off)	"3"
CCS READY M-CPU	Cruise control system standby condition (Main CPU) / ON or OFF	ON/OFF: Change ON/OFF each time main switch is pushed in.	"1"
CCS INDICATOR M-CPU	Cruise indicator signal (Main CPU)/ON or OFF	ON: "CRUISE" ON OFF: "CRUISE" OFF	"2"
CANCEL SW	CANCEL SW signal / ON or OFF	ON: CANCEL SW ON OFF: CANCEL SW OFF	-
-/SET SW	-/SET SW signal / ON or OFF	ON: -/SET SW ON OFF: -/SET SW OFF	-
+/RES SW	+/RES SW signal / ON or OFF	ON: +/RES SW ON OFF: +/RES SW OFF	-
STP LIGHT SW2 M (STP)	Stop light SW signal (Main CPU) / ON or OFF	ON: Brake pedal depressed OFF: Brake pedal released	-
CCS OPER STATUS	PNP SW signal (D position)7 ON or OFF	ON: Shift D position OFF: Except shift D position	-
# CODES	Number of DTC recorded / 0 to 255	Min.:0 Max.:4	-

HINT:

"3" is OK but "1" is NG - ECM failure
"1" is OK but "2" is NG - DTC output or ECM failure
"3" is OK but the cruise indicator does not come on - CRUISE main indicator, wire harness or ECM failure

PERFORM ACTIVE TEST

HINT:
Using Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts. This non-intrusive function inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
1. Connect Techstream to the DLC3.
2. Turn the ignition switch to the ON position.
3. Turn the Techstream main switch on.
4. Enter the following menu items: Body Electrical / Combination Meter / Active Test.
5. Perform "Active Test" according to the display on the tester.
HINT:

The ignition switch must be turned on to proceed with the Active Test using Techstream.

ACTIVE TEST

Tester Display	Test Part	Control Range	Diagnostic Note
Indicat. Lamp Cruise	Cruise Main Indicator Light	BLINK / OFF	-