Data List/Active Test
- DATA LIST
HINT:
Using Techstream to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.
NOTE: In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.- Warm up the engine.
- Turn the ignition switch off.
- Connect Techstream to the DLC3.
- Turn the ignition switch on (IG).
- Turn Techstream on.
- Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
- According to the display on the tester, read the Data List.
ABS/VSC/TRAC:
DATA LIST - ABS/VSC/TRACTester Display Measurement Item/Range Normal Condition Diagnostic Note ABS Warning Light ABS warning light / ON or OFF ON Warning light ON
OFF Warning light OFF- VSC Warning Light VSC OFF indicator light / ON or OFF ON Indicator light ON
OFF. Indicator light OFF- Brake Warning Light Brake warning light / ON or OFF ON Warning light ON
OFF Warning light OFF- Slip Indicator Light Slip indicator light / ON or OFF ON Indicator light ON OFF
Indicator light OFF- Downhill Assist Control Light ((1)) Downhill assist control indicator light / ON or OFF ON. Indicator light ON
OFF Indicator light OFF- Buzzer Skid control buzzer / ON or OFF ON Buzzer ON
OFF Buzzer OFF- Stop Light SW Stop light switch / ON or OFF ON Brake pedal depressed
OFF. Brake pedal released- Parking Brake SW Parking brake switch / ON or OFF ON Parking brake applied
OFF Parking brake released- Main Idle SW Main idle switch / ON or OFF ON Accelerator pedal released
OFF Accelerator pedal depressed- Brake Pedal Load Sensing SW Brake pedal load sensing switch / ON or OFF ON Brake pedal depressed beyond the specified point
OFF Brake pedal not depressed beyond the specified point- Gear Position Gear position information / P/N, R, 1st-6th, FAIL, NOT R Actual gear position - Shift Lever Position Shift lever position information / P/N, R, D/M, 1st-8th/B, FAIL Actual shift lever position - Shift Information Shift information / ON or OFF ON During gear change - Inspection Mode Inspection mode / OTHER or INSPECT OTHER Normal mode
INSPECT Inspection mode- Number of IG ON (Inspection) Number of ignition switch being turned on (IG) after entering inspection mode / min 0, max 255 Min: 0
Max: 255- Downhill Assist Control SW ((1)) Downhill assist control switch / ON or OFF ON Switch ON
OFF Switch OFF- Master Cylinder Sensor Master cylinder pressure sensor / min 0 V, max 5 V When brake pedal is released
0.3 to 0.9 VReading increases when brake pedal is depressed Zero Point of M/C Memorized zero value / min. -12.5 MPa, max. 12.4 MPa Min. -12.5 MPa
Max. 12.4 MPa- Deceleration Sensor Acceleration sensor /min -18.52 m/s2 , max. 18.39 m/s2 Min: -18.52 m/s2
Max: 18.39 m/s2Reading changes when vehicle is bounced Zero Point of Decele Memorized zero value / min. -25.11 m/s2 , max. 24.91 m/s2 Min. -25.11 m/s2
Max. 24.91 m/s2- Deceleration Sensor 2 Acceleration sensor 2 / min. -18.52 m/s2 , max. 18.39 m/s2 Min. -18.52 m/s2
Max. 18.39 m/s2Reading changes when vehicle is bounced Zero Point of Decele 2 Memorized zero value / min. -25.11 m/s2 , max. 24.91 m/s2 Min. -25.11 m/s2
Max. 24.91 m/s2- Yaw Rate Sensor Yaw rate sensor / min. -128 deg/s, max. 127 deg/s Vehicle stationary 0 deg/s
Right turn -128 to 0 deg/s
Left turn 0 to 127 deg/s- Zero Point of Yaw Rate Memorized zero value / min -128 deg/s, max 127 deg/s Min. -128 deg/s
Max. 127 deg/s- Yaw Rate Sensor 2 Yaw rate sensor 2 / min -128 deg/s, max 127 deg/s Vehicle stationary 0 deg/s
Right turn -128 to 0 deg/s
Left turn 0 to 127 deg/s- Zero Point of Yaw Rate 2 Memorized zero value / min -128. deg/s, max. 127 deg/s Min. -128 deg/s
Max. 127 deg/s- Steering Angle Sensor Steering angle sensor/min. -3276.8 deg, max 3276.7 deg Left turn Increase
Right turn Decrease- Zero Point of Steering Angle Memorized zero value/min -3276.8 deg, max 3276.7 deg Min -3276.8 deg
Max 3276.7 deg- Lateral G Lateral G / min -25 11 m/s2 , max 24 91 m/s2 Min -25 11 m/s2
Max 24 91 m/s2- Forward and Rearward G Forward and backward G / min -25.11 m/s2 , max 24.91 m/s2 Min. -25.11 m/s2
Max. 24.91 m/s2- Yaw Rate Value Yaw rate value /min -128 deg/s, max 127 deg/s Min. -128 deg/s
Max. 127 deg/s- Steering Angle Value Steering angle value / min -3276.8 deg, max 3276.7 deg Min. -3276.8 deg
Max. 3276.7 deg- FR Wheel Speed FR wheel speed sensor reading / min 0 km/h (0 mph), max 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer Tester Display Measurement Item/Range Normal Condition Diagnostic Note FL Wheel Speed FL wheel speed sensor reading / min. 0 km/h (0 mph), max 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer RR Wheel Speed RR wheel speed sensor reading / min. 0 km/h (0 mph), max 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer RL Wheel Speed RL wheel speed sensor reading / min 0 km/h (0 mph), max 326 km/h (202 mph) Actual wheel speed Similar speed as indicated on speedometer Vehicle Speed Maximum wheel speed sensor reading / min 0 km/h (0 mph), max 326 km/h (202 mph) Actual vehicle speed Speed indicated on speedometer FR Wheel Acceleration FR wheel acceleration / min. -200.84 m/s2 , max. 199.27 m/s2 0 m/s2 - FL Wheel Acceleration FL wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 0 m/s2 - RR Wheel Acceleration RR wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 0 m/s2 - RL Wheel Acceleration RL wheel acceleration / min.: -200.84 m/s2 , max.: 199.27 m/s2 0 m/s2 - FR Wheel ABS Ctrl Status FRL wheel ABS control status / ON or OFF ON During control - FL Wheel ABS Ctrl Status FL wheel ABS control status / ON or OFF ON. During control - RR Wheel ABS Ctrl Status RR wheel ABS control status / ON or OFF ON During control - RL Wheel ABS Ctrl Status RL wheel ABS control status / ON or OFF ON During control - RR Wheel EBD Ctrl Status RR wheel EBD control status / ON or OFF ON During control - RL Wheel EBD Ctrl Status RL wheel EBD control status / ON or OFF ON. During control - BA Ctrl Status BA control status / ON or OFF ON During control - TRC (TRAC) Ctrl Status TRAC control status / ON or OFF ON. During control - TRC (TRAC) Engine Ctrl Status TRAC engine control status / ON or OFF ON During control - TRC (TRAC) Brake Ctrl Status TRAC brake control status / ON or OFF ON. During control - FR Wheel VSC Ctrl Status FR wheel VSC control status / ON or OFF ON During control - FL Wheel VSC Ctrl Status FL wheel VSC control status / ON or OFF ON During control - RR Wheel VSC Ctrl Status RR wheel VSC control status / ON or OFF ON. During control - RL Wheel VSC Ctrl Status RL wheel VSC control status / ON or OFF ON During control - Engine Revolutions Engine revolutions / min. 0 r/min, max: 65535 r/min Min: 0 r/min
Max: 65535 r/min- Real Engine Torque Real engine torque / min: -1024 N*m, max: 1023 N*m Min. -1024 N*m
Max. 1023 N*m- Accelerator Opening Angle % The difference of a present accelerator/min 0%, max 128% Min. 0%
Max 128%- Solenoid Relay ABS solenoid relay / ON or OFF ON. Solenoid relay ON
OFF. Solenoid relay OFF- ABS Motor Relay ABS motor relay / ON or OFF ON. Motor relay ON
OFF: Motor relay OFF- Fail Safe Motor Relay ABS motor fail safe relay / ON or OFF ON Motor relay ON
OFF Motor relay OFF- TR(A)C/VSC Solenoid (SM2) Master cut solenoid (SM2) / ON or OFF ON Operates - TR(A)C/VSC Solenoid (SM1) Master cut solenoid (SM1) / ON or OFF ON Operates - ABS Solenoid (SFRH) ABS solenoid (SFRH) / ON or OFF ON Operates - ABS Solenoid (SFRR) ABS solenoid (SFRR) / ON or OFF ON Operates - ABS Solenoid (SFLH) ABS solenoid (SFLH) / ON or OFF ON Operates - ABS Solenoid (SFLR) ABS solenoid (SFLR) / ON or OFF ON Operates - ABS Solenoid (SRRH) ABS solenoid (SRRH) / ON or OFF ON Operates - ABS Solenoid (SRRR) ABS solenoid (SRRR) / ON or OFF ON Operates - ABS Solenoid (SRLH) ABS solenoid (SRLH) / ON or OFF ON Operates - ABS Solenoid (SRLR) ABS solenoid (SRLR) / ON or OFF ON Operates - FR Speed Open FR speed sensor open detection / ERROR or NORMAL ERROR Momentary interruption
NORMAL Normal- FL Speed Open FL speed sensor open detection / ERROR or NORMAL ERROR Momentary interruption
NORMAL Normal- RR Speed Open RR speed sensor open detection / ERROR or NORMAL ERROR Momentary interruption
NORMAL Normal- RL Speed Open RL speed sensor open detection / ERROR or NORMAL ERROR Momentary interruption
NORMAL Normal- EFI Communication Open EFI communication open detection / ERROR or NORMAL ERROR Momentary interruption
NORMAL Normal- Yaw Rate Open Yaw rate sensor open detection / ERROR or NORMAL ERROR Momentary interruption
NORMAL Normal- Deceleration Open Acceleration sensor open detection / ERROR or NORMAL ERROR Momentary interruption
NORMAL Normal- Steering Open Steering angle sensor open detection / ERROR or NORMAL ERROR Momentary interruption
NORMAL Normal- Master Cylinder Open Master cylinder pressure sensor open detection / ERROR or NORMAL ERROR Momentary interruption
NORMAL Normal- MT Voltage Value Motor driving monitor voltage / min 0 V, max 255 V Min 0 V
Max 255 V- TRC/VSC Off Mode VSC OFF switch / NORMAL, TRC OFF or VSC OFF NORMAL Normal mode
TRC OFF TRAC off mode
VSC OFF VSC off mode- Number of DTC Number of DTC recorded / min 0, max 255 Min 0
Max 255- (1) for 4WD - ACTIVE TEST
HINT:
Using Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing any parts to operate without removing any parts. This non-intrusive functional inspection can be very useful because intermittent operation may be discovered before parts or wiring is disturbed. Performing Active Tests early in troubleshooting is one way to save diagnostic time. Data List information can be displayed while performing Active Tests.
- Warm up the engine.
- Turn the ignition switch off.
- Connect Techstream to the DLC3.
- Turn the ignition switch on (IG).
- Turn Techstream on.
- Enter the following menus: Chassis / ABS/VSC/ TRAC / Active Test.
- According to the display on the tester, perform the Active Test.
ABS / VSC / TRAC:
ACTIVE TEST - ABS/VSC/TRACTester Display Test Part Control Range Diagnostic Note ABS Warning Light ABS warning light Warning light ON / OFF Observe combination meter VSC Warning Light VSC OFF indicator light Indicator light ON / OFF Observe combination meter Brake Warning Light Brake warning light Warning light ON / OFF Observe combination meter Slip Indicator Light Slip indicator light Indicator light ON / OFF Observe combination meter Downhill Assist Control Light ((1)) Downhill assist control indicator light Indicator light ON / OFF Observe combination meter Buzzer Skid control buzzer Buzzer ON / OFF Buzzer can be heard Solenoid Relay ABS solenoid relay Relay ON / OFF - Motor Relay ABS motor relay Relay ON / OFF Operating sound of motor can be heard Stop Light Relay ((2)) Stop light control relay Relay ON / OFF Stop lights come on ABS Solenoid (SRLR) ABS solenoid (SRLR) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard ABS Solenoid (SRLH) ABS solenoid (SRLH) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard ABS Solenoid (SRRR) ABS solenoid (SRRR) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard ABS Solenoid (SRRH) ABS solenoid (SRRH) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard ABS Solenoid (SFLR) ABS solenoid (SFLR) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard ABS Solenoid (SFLH) ABS solenoid (SFLH) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard ABS Solenoid (SFRR) ABS solenoid (SFRR) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard ABS Solenoid (SFRH) ABS solenoid (SFRH) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard VSC/TRC Solenoid (SMR) Master cut solenoid (SM2) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard VSC/TRC Solenoid (SMF) Master cut solenoid (SM1) Solenoid ON / OFF Operating sound of solenoid (clicking sound) can be heard (1) for 4WD (2) with downhill assist control (for 4WD) or hill-start assist control