Front Axle Hub: Installation

INSTALL FRONT AXLE HUB BEARING
1. Using SST and a press, install a new front axle hub bearing to the steering knuckle.
  SST 09950-60020 (09951-00720), 09950-70010 (09951-07100)
INSTALL FRONT DISC BRAKE DUST COVER
1. Install the disc brake dust cover to the steering knuckle with the 3 bolts.
  Torque: 8.3 N*m (85 kgf*cm, 73 in.*lbf)
  
  Fig 1: Installing Front Axle Hub Bearing Using SST
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT AXLE HUB SUB-ASSEMBLY
1. Using SST and a press, install the front axle hub sub-assembly.
  SST 09608-32010, 09950-60010 (09951-00600), 09950-70010 (09951-07100)
  
  Fig 2: Installing Front Axle Hub Sub-Assembly Using SST And Press
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT AXLE HUB HOLE SNAP RING
1. Using snap ring pliers, install a new front axle hub hole snap ring.
INSTALL FRONT LOWER BALL JOINT (See INSTALLATION )

Fig 3: Removing/Installing Front Axle Hub Hole Snap Ring
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
INSTALL FRONT AXLE ASSEMBLY
1. Align the matchmarks and install the front drive shaft assembly to the front axle hub sub-assembly.
  
  Fig 4: Identifying Matchmarks On Front Drive Shaft Assembly And Front Axle Hub Sub-Assembly
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
2. Install the front axle assembly to the front shock absorber with the 2 bolts and 2 nuts.
  Torque: 240 N*m (2450 kgf*cm, 177 ft.*lbf)
  
  NOTE: Be careful not to damage the drive shaft boot or speed sensor rotor.
  
  Fig 5: Locating Front Axle Assembly Bolts And Nuts
  Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CONNECT FRONT LOWER SUSPENSION ARM (See INSTALLATION )
CONNECT TIE ROD END SUB-ASSEMBLY (for 2WD) (See INSTALLATION )
CONNECT TIE ROD END SUB-ASSEMBLY (for 4WD) (See INSTALLATION )
INSTALL FRONT DISC (See INSTALLATION )
INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY (See REPLACEMENT )
TEMPORARILY INSTALL FRONT AXLE SHAFT NUT
1. Clean the threaded parts on the drive shaft and axle hub nut using a non-residue solvent.
  NOTE:
  - Be sure to perform this work for a new drive shaft.
  - Keep the threaded parts free of oil and foreign objects.
2. Using a socket wrench (30 mm), while applying the brakes, temporarily install a new axle hub nut.
  Torque: 216 N*m (2203 kgf*cm, 159 ft.*lbf)
  
  HINT:
  - Stake the axle hub nut after inspecting for looseness and runout in the following steps.
  - Tighten the axle hub nut while the brakes are applied to prevent the front axle from rotating.
SEPARATE FRONT DISC BRAKE CALIPER ASSEMBLY (See REPLACEMENT )
REMOVE FRONT DISC (See REMOVAL )
INSPECT FRONT AXLE HUB BEARING LOOSENESS (See ON-VEHICLE INSPECTION )
INSPECT FRONT AXLE HUB RUNOUT (See ON-VEHICLE INSPECTION )
INSTALL FRONT DISC (See INSTALLATION )
INSTALL FRONT DISC BRAKE CALIPER ASSEMBLY (See REPLACEMENT )
CONNECT FRONT SPEED SENSOR (See INSTALLATION )
INSTALL FRONT AXLE SHAFT NUT
1. Using a chisel and hammer, stake the axle hub nut.
INSTALL FRONT WHEEL
Torque: 103 N*m (1050 kgf*cm, 76 ft.*lbf)
INSPECT AND ADJUST FRONT WHEEL ALIGNMENT
HINT:

(See FRONT WHEEL ALIGNMENT )

Fig 6: Staking Axle Hub Nut Using Chisel And Hammer
Courtesy of © TOYOTA, LICENSE AGREEMENT TMS1002
CHECK FOR SPEED SENSOR SIGNAL (w/ VSC)
HINT:

(See TEST MODE PROCEDURE )
CHECK FOR SPEED SENSOR SIGNAL (w/ ABS)
HINT:

(See TEST MODE PROCEDURE )