| Camshaft timing oil control valve assembly |
Resistance: |
1 - 2 |
6.9 to 7.9 Ω at 20 °C (68°F) |
| Throttle with motor body assembly |
Resistance |
1(M-) - 2(M+) |
0.3 to 100 Ω at 20 °C (68°F) |
| Accelerator pedal position No. 1 standard voltage |
Voltage |
Accelerator pedal released |
0.5 to 1.1 V |
| Accelerator pedal depressed |
2.6 to 4.5 V |
| Accelerator pedal position No. 2 standard voltage |
Voltage |
Accelerator pedal released |
1.2 to 2.0 V |
| Accelerator pedal depressed |
3.4 to 5.0 V |
| Mass air flow meter |
Resistance |
1(THA) - 2(E2) |
13.6 to 18.4 KΩ at -20 °C (4°F) |
| 2.21 to 2.69 KΩ at 20 °C (68°F) |
| 0.49 to 0.67 KΩ at 60 °C (140°F) |
| Crankshaft position sensor |
Resistance |
1 - 2 |
1850 to 2450 Ω at 20°C (68°F) |
| Engine coolant temperature sensor |
Resistance: |
1 - 2 |
2.32 to 2.59 Ω at 20 °C (68°F) |
| 1 - 2 |
0.310 to 0.326 Ω at 80°C (176°F) |
| Knock sensor |
Resistance |
1 - 2 |
120 to 280 Ω at 20 °C (68°F) |
| Air fuel ratio sensor (for Bank1) |
Resistance |
2(+B) - 1(HA1A) |
1.8 to 3.4 Ω at 20°C (68°F) |
| 1(HA1A) - 4(A1A-) |
10 kΩ or higher |
| Air fuel ratio sensor (for Bank2) |
Resistance |
2(+B) - 1(HA2A) |
1.8 to 3.4 Ω at 20°C (68°F) |
| 1(HA2A) - 4(A2A-) |
10 kΩ or higher |
| Heated oxygen sensor (for Bank1) |
Resistance |
1(HT1B) - 2 (+B) |
11 to 16 Ω at 20°C (68°F) |
| 1(HT1B) - 4 (E2) |
10 kΩ or higher |
| Heated oxygen sensor (for Bank2) |
Resistance |
1(HT2B) - 2 (+B) |
11 to 16 Ω at 20°C (68°F) |
| 1(HT2B) - 4 (E2) |
10 kΩ or higher |
| EFI relay |
Resistance |
3 - 5 |
10 kΩ or higher (Battery voltage not applied) |
| Below 1 Ω (Battery voltage applied to terminals 1 and 2) |
| Circuit opening relay |
Resistance |
3 - 5 |
10 kΩ or higher (Battery voltage not applied) |
| 1 - 2 |
Below 1 Ω (Battery voltage applied to terminals 1 and 2) |
| A/F sensor heater relay |
Resistance |
3 - 4 |
Below 1 Ω (Battery voltage not applied) |
| 10 kΩ or higher (Battery voltage applied to terminals 1 and 2) |
| 3 - 5 |
10 kΩ or higher (Battery voltage not applied) |
| Below 1 Ω (Battery voltage applied to terminals 1 and 2) |