LEMON Manuals: Even more car manuals for everyone: 1960-2025
Home >> Toyota >> 2012 >> Prius V >> Repair and Diagnosis >> Engine Performance >> System >> Engine Control System [Diagnostic Codes & Circuit Tests] >> SFI System >> Circuit Tests >> VC Output Circuit >> Procedure
April 5, 2026: LEMON Manuals is launched! Read the announcement.

VC Output Circuit: Procedure

  1. CHECK MIL 
    1. Check that the Malfunction Indicator Lamp (MIL) illuminates when turning the power switch on (IG).

      OK

      MIL lights up.

    NG → See step   2 

    OK → See step   8 

  2. CHECK CONNECTION BETWEEN TECHSTREAM AND ECM 
    1. Connect the Techstream to the DLC3.
    2. Turn the power switch on (IG).
    3. Turn the Techstream on.
    4. Check the communication between the Techstream and ECM.
      RESULT

      Result Proceed to
      Communication is not possible A
      Communication is possible B

    B → See step   9 

    A: Go to next step 

  3. CHECK MIL (THROTTLE POSITION SENSOR) 
    1. Disconnect the throttle position sensor connector.
    2. Turn the power switch on (IG).
    3. Check the MIL.
      RESULT

      Result Proceed to
      MIL does not illuminate A
      MIL illuminates B

    B → See step   10 

    A: Go to next step 

  4. CHECK MIL (CAMSHAFT POSITION SENSOR) 
    1. Disconnect the camshaft position sensor connector.
    2. Turn the power switch on (IG).
    3. Check the MIL.
      RESULT

      Result Proceed to
      MIL does not illuminate A
      MIL illuminates B

    B → See step   11 

    A: Go to next step 

  5. CHECK MIL (MANIFOLD ABSOLUTE PRESSURE SENSOR) 
    1. Disconnect the manifold absolute pressure sensor connector.
    2. Turn the power switch on (IG).
    3. Check the MIL.
      RESULT

      Result Proceed to
      MIL does not illuminate A
      MIL illuminates B

    B → See step   12 

    A: Go to next step 

  6. CHECK MIL (CANISTER PUMP MODULE) 
    1. Disconnect the canister pump module connector.
    2. Turn the power switch on (IG).
    3. Check the MIL.
      RESULT

      Result Proceed to
      MIL does not illuminate A
      MIL illuminates B

    B → See step   13 

    A: Go to next step 

  7. CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) 
    1. Disconnect the throttle position sensor connector.
    2. Disconnect the camshaft position sensor connector.
    3. Disconnect the manifold absolute pressure sensor connector.
    4. Disconnect the canister pump module connector.
    5. Disconnect the ECM connector.
    6. Measure the resistance according to the value(s) in the table below.

      Standard Resistance

      Tester Connection Condition Specified Condition
      D4-5 (VC) or D28-88 (VCTA) - Body ground Always 10 kΩ or higher
      D18-3 (VC) or D28-99 (VCV1) - Body ground Always 10 kΩ or higher
      D3-3 (VC) or D28-72 (VCPM) - Body ground Always 10 kΩ or higher
      o1-6 (VCC) or D28-113 (VCPP) - Body ground Always 10 kΩ or higher

    NG → REPAIR OR REPLACE HARNESS OR CONNECTOR 

    OK → See step   14 

  8. PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE. Refer to  PROBLEM SYMPTOMS TABLE 
  9. GO TO MIL CIRCUIT. Refer to  MIL Circuit  
  10. REPLACE THROTTLE BODY ASSEMBLY. Refer to  REMOVAL 
  11. REPLACE CAMSHAFT POSITION SENSOR. Refer to  REMOVAL 
  12. REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR. Refer to  REMOVAL 
  13. REPLACE CANISTER PUMP MODULE. Refer to  REMOVAL - Step 2 
  14. REPLACE ECM. Refer to  REMOVAL 
scientia non olet · About LEMON Manuals