Specifications Index
SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT OIL CAPACITIES | ||
| Torque | REFRIGERANT SYSTEM, FASTENER TIGHTENING SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | Twelve-point bolt with ribs is 70 Nm + an additional 90° (1/4) turn Twelve-point bolt without ribs is 200 Nm + an additional 180° (1/2) turn |
||
| Rear | 200 Nm + an additional 180° (1/2) turn | ||
| Battery | 27 BATTERY, STARTER, GENERATOR, CRUISE CONTROL | ||
| Brakes | |||
| Bleeding Sequence | HYDRAULIC SYSTEM, BLEEDING | ||
| Disc Brakes | |||
| Front | FRONT BRAKES | ||
| Rear | REAR BRAKES | ||
| Torque | |||
| Mechanical Components | FASTENER TIGHTENING SPECIFICATIONS | ||
| Hydraulic Components | FASTENER TIGHTENING SPECIFICATIONS | ||
| Anti-lock Brake System | FASTENER TIGHTENING SPECIFICATIONS | ||
| Charging | |||
| Generator | N/A | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | |||
| 2.0L | RIBBED BELT | ||
| 3.6L | RIBBED BELT, ENGINE CODE BLV RIBBED BELT, ENGINE CODE CNNA |
||
| Belt Routing | |||
| 2.0L | See fig. 26 under RIBBED BELT | ||
| 3.6L | See fig. 23 under RIBBED BELT, ENGINE CODE BLV See fig. 30 under RIBBED BELT, ENGINE CODE CNNA |
||
| Engine Cooling | |||
| General Service Specifications | Refer to the approrpiate FLUID CAPACITY TABLES information. | ||
| Radiator Cap Pressure | |||
| 2.0L | 1.4 to 1.6 bar | ||
| 3.6L | 1.4 to 1.6 bar | ||
| Thermostat R & I | |||
| 2.0L | COOLANT THERMOSTAT HOUSING | ||
| 3.6L | COOLANT THERMOSTAT | ||
| Water Pump R & I | |||
| 2.0L | COOLANT PUMP | ||
| 3.6L | COOLANT PUMP | ||
| Engine Mechanical | |||
| 2.0L | |||
| Compression | COMPRESSION TEST | ||
| Oil Pressure | Start the engine and increase the engine speed: The LED must illuminate at 1.2 to 1.6 bar Increase the engine speed further. At 2000 RPM and an oil temperature of 80 °C (176 °F), the oil pressure must be between 2.7 and 4.5 bar. At higher engine speeds the oil pressure must not exceed 7.0 bar |
||
| Overhaul | 10 ENGINE ASSEMBLY | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| 3.6L | |||
| Compression | COMPRESSION, CHECKING | ||
| Oil Pressure | 1500 RPM: at least 1.7 bar 2000 RPM: 3.0 to 5.5 bar Above 2000 RPM: maximum 7.0 bar |
||
| Overhaul | 10 ENGINE ASSEMBLY | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Flywheel/Flex Plate Torque | 60 Nm + an additional 90° (1/4) turn | ||
| Fuel System | |||
| Pressure Specification | |||
| 2.0L | The fuel injection system is separated into a high pressure side, where the pressure is a maximum of approximately 120 bar and a low pressure side, where the pressure is approximately 6 bar | ||
| 3.6L | The fuel injection system is separated into a high pressure side, where the pressure is a maximum of approximately 120 bar and a low pressure side, where the pressure is approximately 6 bar. | ||
| Fuel Pressure Test Procedure | |||
| 2.0L | FUEL PRESSURE SENSOR -G247-, CHECKING | ||
| 3.6L | FUEL PRESSURE SENSOR CHECKING | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil-On-Plug | ||
| Ignition Wires (Routing) | Coil-On-Plug | ||
| Spark Plug | |||
| 2.0L | TEST DATA AND SPARK PLUGS | ||
| 3.6L | TEST DATA AND SPARK PLUGS | ||
| Starting | |||
| Starter | N/A | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFIED VALUES | ||
| Torque | |||
| Front | FASTENER TIGHTENING SPECIFICATIONS | ||
| Rear | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 120 Nm | ||