Common Specs & Procedures
SPECIFICATIONS INDEX
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | REFRIGERANT R134A CHARACTERISTICS | ||
| Torque | N/A | ||
| Axle Nut/Hub Nut | |||
| Front | 200 Nm +180° FWD 70 Nm + 90° AWD |
||
| Rear | 200 Nm +180° FWD 70 Nm + 90° AWD |
||
| Battery | 27 BATTERY, STARTER, GENERATOR, CRUISE CONTROL | ||
| Brakes | |||
| Bleeding Sequence | HYDRAULIC SYSTEM, PRE-BLEEDING HYDRAULIC SYSTEM, BLEEDING HYDRAULIC SYSTEM, POST-BLEEDING |
||
| Disc Brakes | FRONT BRAKES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS
Hydraulic Components FASTENER TIGHTENING SPECIFICATIONS Mechanical Components |
||
| Charging | |||
| Generator | N/A | ||
| Torque | N/A | ||
| Drive Belts | |||
| Adjustment | |||
| 2.0L | RIBBED BELT Engine Code: CBFA & CCTA | ||
| 3.6L | RIBBED BELT, ENGINE CODE BLV RIBBED BELT for Engine Code: CNNA |
||
| Belt Routing | |||
| 2.0L | See fig. 53 under Installing for Engine Code: CBFA & CCTA | ||
| 3.6L | See fig. 23 under RIBBED BELT, ENGINE CODE BLV See fig. 18 under RIBBED BELT for Engine Code: CNNA |
||
| Engine Cooling | |||
| General Service Specifications | Refer to the approrpiate FLUID CAPACITY TABLES information. | ||
| Radiator Cap Pressure | |||
| 2.0L | 1.4 to 1.6 bar | ||
| 3.6L | 1.4 to 1.6 bar | ||
| Thermostat R & I | |||
| 2.0L | COOLANT THERMOSTAT | ||
| 3.6L | COOLANT THERMOSTAT | ||
| Water Pump R & I | |||
| 2.0L | COOLANT PUMP | ||
| 3.6L | COOLANT PUMP
for Engine Code(s): BLV COOLANT PUMP for Engine Code(s): CNNA |
||
| Engine Mechanical | |||
| 2.0L | |||
| Compression | COMPRESSION PRESSURE, CHECKING | ||
| Oil Pressure | Oil pressure when the vehicle is idling: 1.2 to 2.1 bar Oil pressure at 2000 RPM: 1.6 to 2.1 bar. Oil pressure at 3700 RPM: 3.0 to 4.0 bar The oil pressure may be 3.0 to 4.0 bar at 2, 000 RPM during the first 1, 000 km. |
||
| Overhaul | 10 ENGINE ASSEMBLY | ||
| Torque | ENGINE, INSTALLING | ||
| 3.6L | |||
| Compression | COMPRESSION, CHECKING
for Engine Code(s): BLV COMPRESSION PRESSURE, CHECKING for Engine Code(s): CNNA |
||
| Oil Pressure | 1500 RPM: at least 1.7 bar (24.6 psi) 2000 RPM: 3.0 to 5.5 bar (43.5 to 79.8 psi) above 2000 RPM: maximum 7.0 bar (101.5 psi) |
||
| Overhaul | 10 ENGINE ASSEMBLY
for Engine Code(s): BLV 10 ENGINE ASSEMBLY for Engine Code(s): CNNA |
||
| Torque | SPECIFICATIONS
for Engine Code(s): BLV |
||
| Fluid Specifications | See FLUIDS under MAINTENANCE tab. | ||
| Flywheel/Flex Plate Torque | N/A | ||
| Fuel System | |||
| Pressure Specification | |||
| 2.0L | The fuel injection system is separated into a high-pressure section where the pressure is a maximum of approximately 120 bar (1740 psi) and a low-pressure section where the pressure is approximately 6 bar (87 psi). | ||
| 3.6L | The pressures may have a maximum difference of 5 bar | ||
| Fuel Pressure Test Procedure | |||
| 2.0L | Fuel Pressure Sensor -G247-, CHECKING | ||
| 3.6L | FUEL PRESSURE SENSOR CHECKING
for Engine Code(s): BLV Fuel Pressure Sensor - G247-, CHECKING for Engine Code(s): CNNA |
||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil-On-Plug | ||
| Ignition Wires (Routing) | Coil-On-Plug | ||
| Spark Plug | |||
| 2.0L | TEST DATA AND SPARK PLUGS | ||
| 3.6L | TEST DATA AND SPARK PLUGS
for Engine Code(s): BLV TEST DATA AND SPARK PLUGS for Engine Code(s): CNNA |
||
| Starting | |||
| Starter | STARTER, CHECKING | ||
| Torque | N/A | ||
| Wheel Alignment | |||
| Adjustment Specifications | WHEEL ALIGNMENT SPECIFIED VALUES | ||
| Torque | FASTENER TIGHTENING SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 120 Nm | ||