Overview - Control Module And Hydraulic Unit
WARNING: This page is about a different car, the 2023 Volkswagen Atlas. However, it is still accessible from the selected car via links, so may be relevant.
- ABS Control Module -J104-
- Removing and installing. Refer to ABS CONTROL MODULE AND ABS HYDRAULIC UNIT, REMOVING AND INSTALLING, GASOLINE ENGINE .
- ABS Hydraulic Unit -N55-
- Removing and installing. Refer to ABS CONTROL MODULE AND ABS HYDRAULIC UNIT, REMOVING AND INSTALLING, GASOLINE ENGINE .
- TORX®
Bolt
- Tighten the new TORX® bolts in two steps, switching back and forth.
- 1. Step: preliminary tightening specification: 1 Nm to 1.5 Nm (to position the seal)
- 2. Step: final tightening specification: 2.5 Nm
- Brake Line
- With standard tool: 14 Nm
- With special tools VAS6854 (Mini Torque Wrench), VAG1410/7 (Torque Wrench - Universal Joint) and VAG1410/6 (Open Ring Spanner Insert - AF 11mm): 12 Nm
- To the right rear brake caliper
- Identification: 5.25 mm diameter and tube fitting with a M12 x 1 thread
- Brake Line
- With standard tool: 14 Nm
- With special tools VAS6854 (Mini Torque Wrench), VAG1410/7 (Torque Wrench - Universal Joint) and VAG1410/6 (Open Ring Spanner Insert - AF 11mm): 12 Nm
- To the left front brake caliper
- Identification: 5.25 mm diameter and tube fitting with a M10 x 1 thread
- Brake Line
- With standard tool: 14 Nm
- With special tools VAS6854 (Mini Torque Wrench), VAG1410/7 (Torque Wrench - Universal Joint) and VAG1410/6 (Open Ring Spanner Insert - AF 11mm): 12 Nm
- To the right front brake caliper
- Identification: 5.25 mm diameter and tube fitting with a M12 x 1 thread
- Brake Line
- With standard tool: 14 Nm
- With special tools VAS6854 (Mini Torque Wrench), VAG1410/7 (Torque Wrench - Universal Joint) and VAG1410/6 (Open Ring Spanner Insert - AF 11mm): 12 Nm
- To the left rear brake caliper
- Identification: 5.25 mm diameter and tube fitting with a M10 x 1 thread
- Brake Line
- With standard tool: 14 Nm
- With special tools VAS6854 (Mini Torque Wrench), VAG1410/7 (Torque Wrench - Universal Joint) and VAG1410/6 (Open Ring Spanner Insert - AF 11mm): 12 Nm
- Brake master cylinder/primary piston circuit to hydraulic unit
- Identification: 6 mm diameter and pipe fitting with a M12 x 1 thread
- Brake Line
- With standard tool: 14 Nm
- With special tools VAS6854 (Mini Torque Wrench), VAG1410/7 (Torque Wrench - Universal Joint) and VAG1410/6 (Open Ring Spanner Insert - AF 11mm): 12 Nm
- Brake master cylinder/secondary piston circuit to hydraulic unit
- Identification: 6 mm diameter and pipe fitting with a M12 x 1 thread
- Brake Booster
- Overview - Brake Booster/Brake Master Cylinder. Refer to OVERVIEW - BRAKE BOOSTER/BRAKE MASTER CYLINDER .
- Bracket
- After installing, heck for secure fit
- TORX®
Bolt
- 8 Nm
- Rubber Bushing
- Heat Shield
Refer to the appropriate Electronic Parts Information for the allocation.
- Hex Nut
- 20 Nm
- Bracket
- Hex Nut
- 20 Nm