Common Specs & Procedures
GIULIA COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | A/C SYSTEM | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | TORQUE SPECIFICATIONS | ||
| Rear | TORQUE SPECIFICATIONS | ||
| Battery | BATTERY | ||
| Brakes | |||
| Bleeding Sequence | STANDARD PROCEDURE | ||
| Disc Brakes | |||
| Service Specifications | TECHNICAL SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Charging | |||
| Generator | GENERATOR | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | Serpentine belt used, not adjustable. | ||
| Drive Belt Routing | |||
| 2.0L | Refer to appropriate "Belt Routing" figure under REMOVAL AND INSTALLATION | ||
| 2.9L | Refer to appropriate "Belt Routing" figure under REMOVAL AND INSTALLATION | ||
| Engine Cooling | |||
| General Service Specifications | |||
| 2.0L | DESCRIPTION AND OPERATION | ||
| 2.9L | DESCRIPTION AND OPERATION | ||
| Radiator Cap Pressure | 20 psi | ||
| Thermostat R & I | |||
| 2.0L | Information not available from manufacturer | ||
| 2.9L | REMOVAL AND INSTALLATION | ||
| Water Pump R & I | |||
| 2.0L | REMOVAL AND INSTALLATION | ||
| 2.9L | REMOVAL AND INSTALLATION | ||
| Engine Mechanical | |||
| 2.0L | |||
| Compression | Compression should not be less than 689 kPa (100 psi) and not vary more than 25 percent from cylinder to cylinder. | ||
| Oil Pressure | Refer to OIL PRESSURE tables under SPECIFICATIONS | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| 2.9L | |||
| Compression | Compression should not be less than 689 kPa (100 psi) and not vary more than 25 percent from cylinder to cylinder. | ||
| Oil pressure | Refer to OIL PRESSURE table under SPECIFICATIONS . | ||
| Overhaul | SPECIFICATIONS | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | |||
| 2.0L | 81 ft. lbs. (110 N.m). | ||
| 2.9L | 67 ft. lbs. (91 N.m). | ||
| Fuel System | |||
| Pressure Specification | |||
| 2.0L | CHECKING THE LOW PRESSURE FUEL DELIVERY SYSTEM | ||
| 2.9L | CHECKING THE LOW PRESSURE FUEL DELIVERY SYSTEM | ||
| Fuel Pressure Test Procedure | |||
| 2.0L | CHECKING THE LOW PRESSURE FUEL DELIVERY SYSTEM | ||
| 2.9L | CHECKING THE LOW PRESSURE FUEL DELIVERY SYSTEM | ||
| Fuel Filter Location | Fuel filters are integrated into the main fuel pump module. | ||
| Fuel Filter R & I | |||
| 2.0L | REMOVAL AND INSTALLATION | ||
| 2.9L | REMOVAL AND INSTALLATION | ||
| Ignition | |||
| Firing Order & Cylinder Identification | FIRING ORDER & CYLINDER IDENTIFICATION | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| 2.0L | |||
| Type | Recommended to use Mopar Spark Plugs | ||
| Gap | 0.024 in. (0.60 mm) | ||
| Torque | 168 In. Lbs. (19 N.m) | ||
| 2.9L | |||
| Type | Recommended to use Mopar Spark Plugs | ||
| Gap | Information not available from manufacturer | ||
| Torque | 159 In. Lbs. (18 N.m) | ||
| Starting | |||
| Starter | STARTER | ||
| Torque | TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | TECHNICAL SPECIFICATIONS | ||
| Torque | Front: TORQUE SPECIFICATIONS , Rear: TORQUE SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 89 ft. lbs. (120 N.m) | ||