Common Specs & Procedures Index
COMMON SPECS & PROCEDURES
| SYSTEM | SPECIFICATION/PROCEDURE | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | Approximate Fluid Capacities | ||
| Torque | Fastener Specifications | ||
| Wheel Drive Shaft Nut | |||
| Rear | First Pass: 330 N.m (244 lb ft) Second Pass: loosen 45 degrees Final Pass: 270 N.m (199 lb ft) |
||
| Battery | Battery Electrical Drain/Parasitic Load Test | ||
| Brakes | |||
| Bleeding Sequence | J55 - RIGHT FRONT, LEFT FRONT, LEFT REAR, RIGHT REAR - See Hydraulic Brake System Bleeding (J55)
. JL9 - LEFT REAR, LEFT FRONT, RIGHT FRONT, RIGHT REAR - See Hydraulic Brake System Bleeding (JL9) . |
||
| Disc Brakes | |||
| Service Specifications | Disc Brake Component Specifications | ||
| Torque | Fastener Specifications | ||
| Charging | |||
| Generator | Charging System Test | ||
| Torque | Fastener Specifications | ||
| Drive Belts | |||
| Adjustment | Non-Adjustable Serpentine Belt | ||
| Drive Belt Routing | See the figure under: Water Pump and Generator Belt Replacement | ||
| Engine Cooling | |||
| General Service Specifications | Specifications | ||
| Radiator Cap Pressure | Radiator Surge Tank Cap Testing | ||
| Thermostat R & I | Engine Coolant Thermostat Replacement - At Engine Coolant Manifold or Engine Coolant Thermostat Replacement - Radiator Inlet Hose to Auxiliary Radiator Inlet Pipe (with V09) or Engine Coolant Thermostat Replacement - Auxiliary Radiator Inlet Hose to Auxiliary Radiator Inlet Hose | ||
| Water Pump R & I | Water Pump Replacement | ||
| Engine Mechanical | |||
| Compression | See Engine Compression Test | ||
| Oil Pressure - Minimum - Hot | @ 1000 RPM: 152 kPa (22 psi) @ 2000 RPM: 207 kPa (30 psi) @ 3000 RPM: 228 kPa (33 psi) |
||
| Overhaul | Engine Mechanical Specifications | ||
| Torque | Fastener Specifications | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate Torque | |||
| Flex Plate | First Pass: 22 lb ft (30 N.m) Final Pass: additional 45 degrees |
||
| Fuel System | |||
| Fuel Pressure Test Procedure | Circuit/System Verification | ||
| Fuel Filter Location | Fuel Filter is Part of the Fuel Tank Fuel Pump Module | ||
| Fuel Filter R & I | See Fuel Tank Fuel Pump Module Replacement | ||
| Ignition | |||
| Firing Order & Cylinder Identification | Firing Order & Cylinder Identification | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | Coil On Plug | ||
| Spark Plug | |||
| See Parts Catalog for Application | |||
| Gap | 0.95-1.10 mm (0.037-0.043 in) | ||
| Torque | 20 N.m (15 lb ft) | ||
| Starting | |||
| Starter R & I | Starter Replacement | ||
| Torque | Fastener Specifications | ||
| Wheel Alignment | |||
| Adjustment Specifications | Wheel Alignment Specifications | ||
| Torque | Fastener Specifications | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 140 lb ft (190 N.m) For Tightening Sequence, Please see the Figure Under Installation Procedure |
||