Common Specs & Procedures Index
KIZASHI COMMON SPECS & PROCEDURES
| System | Specification/Procedure | ||
|---|---|---|---|
| Air Conditioning | |||
| Service | A/C SYSTEM PERFORMANCE INSPECTION | ||
| Torque | SPECIFICATIONS | ||
| Axle Nut/Hub Nut | |||
| Front | 184.5 ft. lbs. (250 N.m) | ||
| Rear | 184.5 ft. lbs. (250 N.m) | ||
| Battery | CHARGING SYSTEM SPECIFICATIONS | ||
| Brakes | |||
| Bleeding Sequence | AIR BLEEDING OF BRAKE SYSTEM | ||
| Disc Brakes | |||
| Service Specifications | For front brakes, refer to appropriate component INSPECTION procedure under REPAIR INSTRUCTIONS . For rear brakes, refer to appropriate component INSPECTION procedure under REPAIR INSTRUCTIONS . Specifications are included in article text. | ||
| Torque | For front brakes, refer to SPECIFICATIONS . For rear brakes, refer to SPECIFICATIONS . For parking brake, refer to SPECIFICATIONS . For brake control system, refer to SPECIFICATIONS . For electronic stability control, refer to SPECIFICATIONS . | ||
| Drum Brakes | |||
| Service Specifications | N/A | ||
| Torque | N/A | ||
| Charging | |||
| Generator | CHARGING SYSTEM SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUE SPECIFICATIONS | ||
| Drive Belts | |||
| Adjustment | ACCESSORY DRIVE BELT TENSION INSPECTION | ||
| Drive Belt Routing | Refer to figure under ACCESSORY DRIVE BELT REMOVAL AND INSTALLATION . | ||
| Engine Cooling | |||
| General Service Specifications | COOLING SYSTEM REFILLING | ||
| Radiator Cap Pressure | 93 - 123 kPa (0.9 - 1.3 kgf/cm2 , 13.4 - 17.3 psi) | ||
| Thermostat R & I | THERMOSTAT REMOVAL AND INSTALLATION | ||
| Water Pump R & I | WATER PUMP REMOVAL AND INSTALLATION | ||
| Engine Mechanical | |||
| Compression | COMPRESSION CHECK | ||
| Oil Pressure | More than 300 - 550 kPa (3.1 - 5.6 kgf/cm2 , 43.5 - 79.8 psi) at 4, 000 RPM | ||
| Overhaul | Refer to appropriate component TABLE in ENGINE MECHANICAL article. | ||
| Torque | For engine component specifications, refer to SPECIFICATIONS . For lubrication component specifications, refer to SPECIFICATIONS . | ||
| Fluid Specifications | See FLUIDS under MAINTENANCE/FLUIDS tab. From within Manager or Service Writer, click the "30/60/90 Interval" or "Maint." button. | ||
| Flywheel/Flex Plate/Drive Plate Torque | 52 ft. lbs. (70 N.m) | ||
| Fuel System | |||
| Pressure Specification | Standard: 375 - 385 kPa (3.8 - 3.9 kgf/cm2 , 54.4 - 55.8 psi) (With fuel pump operating and engine stopped) | ||
| Fuel Pressure Test Procedure | FUEL PRESSURE CHECK | ||
| Fuel Filter Location | FUEL PUMP DESCRIPTION | ||
| Fuel Filter R & I | FUEL PUMP ASSEMBLY REMOVAL AND INSTALLATION | ||
| Ignition | |||
| Firing Order & Cylinder Identification | IDENTIFICATION OF CYLINDER | ||
| Ignition Wires (Resistance) | Coil On Plug | ||
| Ignition Wires (Routing) | N/A | ||
| Spark Plug | |||
| Type: | Iridium type: NGK SILFR6A11, Nickel type: DENSO K16HPR-U11 | ||
| Gap | Standard: 1.0 - 1.1 mm (0.039 - 0.043 in.) | ||
| Torque | 25 N.m (2.5 kg-m, 18.5 lbf-ft) | ||
| Starting | |||
| Starter | CRANKING SYSTEM SPECIFICATIONS | ||
| Torque | TIGHTENING TORQUE SPECIFICATIONS | ||
| Wheel Alignment | |||
| Adjustment Specifications | |||
| Front | FRONT WHEEL ALIGNMENT INSPECTION AND ADJUSTMENT | ||
| Rear | PREPARATION FOR INSPECTION AND ADJUSTMENT | ||
| Torque | For front suspension, refer to SPECIFICATIONS . For rear suspension, refer to SPECIFICATIONS | ||
| Wheel & Tire | |||
| Wheel Lug Nut Torque | 103.5 ft. lbs. (140 N.m) | ||